Project: Water Cooling Turbine

[rendermandan]

Hi everybody!

My water cooling kit came in today.

Here are my ideas for the setup to house the radiator, fans and Resevoir.

My cooling system: the Swiftech H20-120 Premium Kit
http://www.swiftnets.com/assets/images/products/h20-120-premium/h2O-120-premium-res-micro.jpg

Fans: Thermaltake A1926 120mm Blue LED Case Fan
http://images10.newegg.com/NeweggImage/ProductImageCompressAll200/11-999-127-06.jpg

Resevoir: XSPC Passive 250mm Reservoir - SILVER
http://www.frozencpu.com/images/products/main/ex-res-87.jpg

Basically it will look like this:
http://i65.photobucket.com/albums/h205/rendermandan/1.jpg
Back exhaust:
http://i65.photobucket.com/albums/h205/rendermandan/3.jpg
Front looking down tube:
http://i65.photobucket.com/albums/h205/rendermandan/2.jpg
Here is a section cut from the top:
http://i65.photobucket.com/albums/h205/rendermandan/4.jpg


The unit will sit ontop of my computer and, the large tube will house the radiator in the center and air will flow over it to help cooling, then the tube will taper to meet the entering fan and be pushed thru the radiator. I'm going to add a second fan on the back side to help also.
Obviously I did not add any colors to anyting.
It will mostly be silver and black with Blue lights
I'm not sure how to "Dress up" the outside of it yet. but I"m working on it.

I have to order the resevoir yet, but I thought I'd see what you guys thought before I get too far into this.

So... What do you guys think?

[rendermandan]

wow, I'm really getting sucked into this. I just ordered the resevoir, some tubing clamps some steel blue non-conductive coolant and some EL wire. -I'm going to integrate that into the outside of the tube. Man the gears have really started turning on this. not to mention my pocket book is getting thinner by the minute!

[rendermandan]

ok, Here is what I got done over the weekend.

Here's a shot of the parts and the tube I purchased:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1855.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1856.jpg

I started by laying out where to cut the tube so the radiator and fans will slide down into it from the top:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1860.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1859-1.jpg

here are the holes i had to cut:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1871.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1872.jpg

And here is the radiator assembly in the tube:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1873.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1869.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1875.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1876.jpg

Next I cut a section of board to form the backing for the back of the tube.
I then cut the hole out of the middle for air.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1888.jpg

this piece will help me to mold and shape the exit of the tube.

And here it is glued into place:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1893.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1891.jpg

Thats it for now. :)

[rendermandan]

Hmmm... here are the specs posted on NewEggs website.
Model
Brand Thermaltake
Series Thunderblade
Model A1926
Spec
Type Case Fan
Compatibility Case
Fan Size 120mm
Bearing Type Sleeve
RPM 2000 RPM
Air Flow 78 CFM
Noise Level 21 dBA
Power Connector 4 Pin
Color Transparent
LED Blue


21 db doesn't seem that loud to me.
especially for 78 CFM. Most of the ones I've seen in that CFM range are around 30 db or more.

[rendermandan]

Here's my next update:

I left off with just one round form on the rear, so I made another for the front:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1896.jpg

Then added some bondo:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1897.jpg
and some more bondo:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1898.jpg
after some sanding I added some spot putty:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1899.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1900.jpg
here is the finished end.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1903.jpg
Up next was the front part. I first had to make a template to help shape the bondo as access to this area was kind of tight.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1905.jpg
Here is my first attempt. I think it turned out pretty good.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1906.jpg
and here is a shot after adding spot putty:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1915.jpg
While that was drying, I turned my attention to the base. I cut some plastic panel to shape:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1913.jpg
then I beveled the edges of the sides so they will fit better to the tube:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1912.jpg

Thats it. Next up is to cut a design in the sides of the bottoms, and sand the inside of the tube.

FYI, my resevoir, coolant and glow wire should be delivered tomorrow. YEAH!
Later!

[rendermandan]

Ask and ye shall receive:

Here is all the stuff I got from FrozenCpu:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1917.jpg

The resevoir next to a 12" ruler:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1922.jpg
The end. -Notice the small scratches, I could not see them untill the flash.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1918.jpg
The end with the cap off.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1927.jpg
The cap itself:


I got just a small amout done yesterday. I was way to busy with parties and family.

I laid out a pattern on the side of the bottom frame.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1931.jpg
Then I taped the two sides together
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1933.jpg

I have to go get my scroll saw from my Dads workshop to cut them out.

Later.

[rendermandan]

maybe you guys can help me decide on what shape hole to cut into the tube. here are some options I came up with:

Option 1: Just a large rectangular hole.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/holeoption1.jpg

Option 2: One small hole:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/holeoption2.jpg

Option 3: Two larger holes:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/holeoption3.jpg

Option 4: Irregular, geometric shape cut into tube:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/holeoption4.jpg

FYI the bottom panels will not have the holes on them as shown in the pictures. -This one actually matches the design of the bottom and panels that will be applied to the tube. so it fits the best with the overall design. but does it look good? this is what the bottom panels look like
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1931.jpg

Please any comments are welcome!

[rendermandan]

Here is an updated 3d model.

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/WC.jpg

[rendermandan]

I made it out to my dad's tonight.

here is a shot of how much sawdust was on my scroll saw. I haven't used it in a long time!
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1934.jpg

First i drilled the 1/2" hole for the tubing. and small holes for the blade to go through.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1935.jpg

Then cut out around the 1/2" hole
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1939.jpg

Then proceded to cut out the rest:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1945.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1947.jpg

Here is the finished cuts:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1948.jpg

obviously I have some filing and sanding to do, but it turned out pretty good.

[rendermandan]

Tonight I sat down and filed the plastic cutouts.

Now I have 2 identical, mirror image pieces. Isn't that lovely?

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1953.jpg

[rendermandan]

Well, here is tonight's update.

I stopped picked up some semi-translucent plastic as a backer for the bottom section,
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1956.jpg
I cut it to shape and set it aside.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1957.jpg

Then came the task of cutting all the small strips to add to the sides.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1963.jpg
Too bad half way thru, I almost sliced the end of my left middle finger off. I was holding a straight edge and pulled a razor blade right across the tip. -I didn't get any photos.

Then I glued the sides, front and back together and added some gussets for strength.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1958.jpg
Then I glued on the little strips:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1961.jpg

then I glued it to the tube:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1962.jpg

Then just for fun, I checked to see how the tubing would look:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1964.jpg

Thats it for now. Tomorrow I'm going to get working on the cover that goes over the radiator.

Later,

[rendermandan]

Thanks for everyones encouragment on this! I really appreciate it.

So, as promised, here is another update.

I had some blue CC tubes that I never turned on inside my case, so I took those out to use in the base. They will only light up the base area. with that Translucent plastic film I showed earlier.

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1967.jpg

Then I worked on the front and back of the cover for the radiator:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1970.jpg

Here is a shot installed on the tube.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1969-1.jpg

Then for grins, I hooked up the fans to test airflow. WOW does having two of those fans move a lot of air!!! It literlly felt like a vacume at the front of the tube. Here is a shot with the flash on:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1965.jpg
and with the flash off, The bright blue really washes out the image. I will have to play with the settings to try and get a better shot.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1966.jpg

Thats if for a few days, I am going on vacation tomorrow and won't be back untill this weekend, So everyone take care, Later!

[rendermandan]

Hi everybody, I'm back from our Vacation. Unfortunaly my wife's father passed away while we were gone, so we had to cut our trip short. I still managed to find a little time to get a little modding done, so here it goes.

Here is a shot of the sides attached to the radiator housing:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1984.jpg

and some braces on the bottom:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1985.jpg

Then I mocked up the removable top:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1987.jpg

and here it is all together:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_1986.jpg

Then I turned my attention to the 3 tapered rails that run along the tube.
I used a thin sheet of plexi sandwiched between two plate sheets.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2102.jpg

I left a recessed in the bottom edge of the rail:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2106.jpg\

The recess area is for the glow wire I purchased.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2108.jpg

Here are some shots of it lit up:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2109.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2110.jpg

And with the lights out:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2112.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2111.jpg

Then pictures really dont' do it justice. it is much brighter than shown in the pics and looks great!

One down, 2 more to make, then I can mount them on the tube.

[rendermandan]

Thanks everybody, dgrmkrp, You are right, there is a cap on both ends that does hinder the airflow into the fins. however after testing the airflow and feeling how much air moves thru the tube when both fans are running, I thing it will be ok. There is a ton of air moving.

as for how its going to tie into the case... I'm not really sure yet. I have some ideas for the case, but for now I'm just concentrating on the top. FYI, my current computer case is all aluminum silver and clear plexi with blue lights everwhere.
here is a shot:
http://i65.photobucket.com/albums/h205/rendermandan/100_1609.jpg
so obvously, that will be next. :)

[rendermandan]

I had some time to get some stuff done this afternoon. I ended up getting alot more done than I thought I would have.

I finished making the other two light rails.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2124.jpg

I got both sides of the back tube wraped in the trim.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2120.jpg

then before mounting the rails, I took a piece of plexi and melted it to match the ouside of the curve for the main window.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2115.jpg

as I heated it with a torch, I used tape to help pull it down to match the tube.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2117.jpg

This is the final shot with it all taped down ready to cool.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2119.jpg

Then it came time to fit the light rails.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2126.jpg

I had to add trim to the intake end of the tube:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2130.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2131.jpg

then I cut a slot for the wire to tranition from on rail to the next. the other transition happens inside the back box.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2135.jpg

here is a light rail attached to the side
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2128.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2138.jpg

with the lights off
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2139.jpg

so what do you guys think?

Up next comes some serious thought as to the size and shape of the window and how I will cover the edge to make it look good.
I know I have to order more glow wire so I might get some other goodies too.

untill next time,

[rendermandan]

Tonight I added a cover over the glow wire in the front, although its hard to see being white, the flash kind of washed it out.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2145.jpg

Then I laid out the shape of the tube window:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2147.jpg
and using a dremel, I cut it out:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2148.jpg

here is the final window:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2157.jpg

Here is the piece of plexi I heated and bent to match the tube:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2143.jpg

and here it is taped to the tube:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2161.jpg

Just for fun I installed the blue CC lights and tested the cover for the bottom.
I think it is alittle too bright. I might have to come up with something a little less intense for the bottom light.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2156.jpg

I then traced the shape of the window onto the plexi and covered it in tape to protect it.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2162.jpg
Cut it out:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2163.jpg

So my final thoughts on the window were to "MAYBE" laser etch something in the plexi. lets say TBCS? or logo or something. I'm not sure yet.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2167.jpg

happy modding, later!

[rendermandan]

well, to play off your idea of having it fade in and out, what about motion?

maybe I could use a pair of these:
http://www.xoxide.com/sunbeam-meteor-light-blue.html

that way I won't get the heat buildup with cc tubes.

[rendermandan]

You are correct, Spawn, I don't wan't to see any brown tubing. I'm trying to figure out how to install the window and still paint it. Like I said earlier, I may be forced into painting sooner than I had hoped.

Just as small update tonight.
I started to trim the underside of the front. You won't see it much, but in my opinion, attention to detail everwhere counts!

Here is what started with, I added a few trim pieces around the edges:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2177.jpg

Then I simply added a few layers of board down cut to random shapes. Note: this area will not have any glow wire.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2181.jpg

The only other thing I got done was to rough up the surface for the other side of the tube:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2183.jpg

Like I said, just a small update tonight, I'm waiting on the extra glow wire that should be here Thursday.
and an update on doing the laser etching. I will have to wait on that. they guy that I know that has access to it teaches at a local high school and he informed me that he won't have access untill school starts, which is at the end of august.

later,

[rendermandan]

jbdnsn, I agree, I have to find someting not so bright that does not give off much heat. I thought about wiring up some led's myself, not sure exactly what I'm going to do yet.

As for painting, thanks for pointing me toward Commando's tips, I have access to an airbrush, but I don't have an air compressor, so I have to figure that one out. But Yes, I will be air brushing it to make it look liked weathered metal. I really like the paint look on Crimson's Doom 3 case, but I dont' want to copy it exactly. and I want it to look more like the insides of a futuristick turbine.

Thanks again!

[rendermandan]

Here is tonights update. I started to layout the framework for the recessed glow wire lighting on the back side of the tube:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2184.jpg

Then I taped the glow wire along next to it just temporarily.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2185.jpg

Here is the framework all finished: -note: wire has been removed.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2186.jpg

and here it is at night:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2188.jpg

Then I proceded to layer the covers over the top of the wire:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2196.jpg

and her is the effect it gives. The picture really does not show how bright it its. you can see how the glow lights up the other "layers".
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2193.jpg

I am going to finish the covers and add more layers as I see fit. but the wire will be removed for painting. After its painted, I can run the wire back around the path and tuck it in between the tube and the first layer of cover. but the entire thing will be hidden. all you will see will be the glow radiating out from behind the multiple different layers.

What do you think?

[rendermandan]

ok, here we go...

I finished doing right side of the turbine tube:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2201.jpg

Here is a close up:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2199.jpg

Then I moved to the other side:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2204.jpg

Here it is finished.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2209.jpg

The glow wire on the window side will follow the shape of the window and be concealed by a trim ring. I still have to add a little detail to its surface and I can't install it untill I get it painted:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2212.jpg

Speaking of paint. I started to mask off the 3 light bars on the tube. I had to cut a long strip of masking tape to a very thin piece, so I used my stripe cutter from my Airplane modeling days.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2214.jpg

here is a piece of mask on the top section:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2213.jpg

I finished the other 2 sections with mask and now its ready for paint.
My son's birthday is tomorrow so I probably won't get anything done untill after he goes to bed, So I may or may not have another update tomorrow night.

Later,

[rendermandan]

NQ, thats ok, no offense taken. :)

Thanks for the reps and positive comments guys!

Here we go again,

Ask and you shall receive, you wanted to see it painted, here it is in black. BORING black base coat. I have a lot more air brushing to do, but for now I just applied the base coat.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2244.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2246.jpg

While the body was drying I turned my attention to the supports for the resevoir inside. I cut and glued up some strips of plastic.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2237.jpg

Then I used my dremel and a sanding drum to rough out the shape:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2240.jpg

The shape is meant to look kind of like an airplane wing so air will flow smoothly around them.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2242.jpg


I covered it in fine filler:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2249.jpg

Then I used my straight edge sanding block to smooth it out:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2243.jpg

here is the final piece:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2250.jpg

I have to cut it into 6 sections to use around the resevoir. I also have to figure out how I'm going to attach them to the resevoir. so for now, thats it.
Cheers!

[rendermandan]

Once again, here is the nightly update:

Tonight I decided to turn my attention to building the LED light bar for the "Fuel Tank". Here are the Leds and Resistors I got from LSDiodes.com
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2256.jpg

I started by cutting 2 strips and drilling small holes in them equally spaced for the leds.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2257.jpg

Then I added a thin plastic spacer to act as an insulator between the wires.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2258.jpg

Here it is with the led's in place.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2259.jpg

and here is the negative side wired together.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2261.jpg

Here is the positive side soldered together with the resistors.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2262.jpg

Here is a test. They all light up. Excellent the third one from the right on the bottom seems like its not as bright as the others. I might have to replace that one.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2264.jpg

I put it under the tube and put the translucent cover in place.
OH NO! it looks like ****! The led's have too great of a spot light effect and leave very distinct bright spots. I hate it!

Looks like I may be going back to the cold catholdes, they were a little bright, but atleast it was uniform light.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2269.jpg

What to do.....?

[rendermandan]

well, +rep to Sgtm for the first to suggest sanding the tops of the led's, that worked great! Thank you.

I tried it on the left one first.

Before:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2270.jpg

After: Very nice and diffused!
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2271.jpg

And here it is on the body: Much smoother glow, it still has a few "hot" spots but deffinetly not as bad. I can live with that.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2277.jpg

I added a little detail and rivits to the window trim and tube: -I know it looks like alot, but after airbrushing, they will fade away an be hardly noticed.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2285.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2287.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2292.jpg

I also painted the frame on the exhaust fan.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2293.jpg

Then I cut the supports for the resevoir to 3 equal lengths to fit inside the tube:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2301.jpg

here they are as a mock up holding the resevoir centered in a spare piece of the tube:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2298.jpg

I have to notch the end of each one to fit around the chrome mounting ring.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2302.jpg

One down, 5 more to go...

[rendermandan]

imagine if you transfer this genius onto a case

Actually I do have plans to continue this design into a case. Basically everything will be hidden behind panels that light up and be motorized to expose the case and inside. It will be crazy! Not to mention how much work it will be getting all the motorization working.

There are 4 seperate motorized items:
1. Doors that open to a blow hole in the front
2. A dvd burner that motorizes up from the top to expose the slot loading mechanism
3. Motorized flip over panel to acces the fan controller, memory card reader and light switches
4. Some type of covering over the side window to expose a side fan and inside of the case. (still working on the design for this)

But first things first. I have to finish the cooling system, then I can start on the case.

[rendermandan]

Like I said, its still in design phase. I only have a model to show the movable parts. so picture this case covered similar to the turbine only you won't be able to tell a difference between where the openings and movable parts are and the stationary sections are.

Here it is with everything closed.
http://i65.photobucket.com/albums/h205/rendermandan/case-1.jpg

And here it is open:
http://i65.photobucket.com/albums/h205/rendermandan/case-2.jpg

here is another angle to show the twin intake fans and the side fan.
The around the side fan will be clear plexi so you can see the inside of the case.

http://i65.photobucket.com/albums/h205/rendermandan/case-3.jpg

The pop-up slot load dvd player may interfere with the turbine on top (not shown obviously) -so I might have to move it.

Probably put some type of logo on the front of the case in that big blank area, but not sure what yet.

But that gives you guys something to "Drool" over. LOL

[rendermandan]

ok, the vicodin seems to help alot so I got alittle work done tonight.

here is a shot of the fan I painted: Not exactly thrilling, yet...
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2304.jpg

I figured I'd play around with the airbrush tonight so here is what I did.

I took the trim piece for the window and taped off a few areas and painted some rust color:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2305.jpg

then I added some silver and tan:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2306.jpg

Followed that up with a little back drybrushing:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2308.jpg

And here is the final piece:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2310.jpg

So what do you guys think? I still have to do soemthing with the rivits but I have to get a fine paint brush. I was just playing around so I'm not sure if I like the colors. I think it looks pretty good, just not sure If I will like it if the whole thing looks like this. But then again, I wanted a rustic, weathered look to a metal structure so I think I hit it pretty good. Comments?

[rendermandan]

I've been really busy the last few days and haven't had a chance to get much done, so just a small update for now.

I started to airbrush the main body. Here it is with some of tape for the different colors and pieces:

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2311.jpg

and here it is with the tape pulled off (Not Finished)
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2316.jpg

I went to remove some of the tape to get a feel for the whole thing (Not finished yet) and it started to remove some of the paint. looks like I will have to fix that.

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2317.jpg

I also got the other sections of the resevoir supports made. I forgot to take a picture though. Maybe tomorrow night I will get them mounted to the resevoir brackets and can test fit it in the tube. I noticed somethign else I completly forgot about while working. The led light bar I instaled on the bottom of the tube goes right thru where the tubes from the resevoir are supposed to come thru the bottom. Again, I'll have to redo this area somehow.

[rendermandan]

Hi everyone, Sorry its been a while, been busy going to the doctors but lastnight I got some more done.

I finished painting the main round part of the body. I still have to figure out the back half.


Unweathered:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2318.jpg

Weathered:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2322.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2323.jpg

Then I glued the window in place:

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2326.jpg

I also started to run the el wire around the window:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2327.jpg

I have an issue with the el wire for the other side, It has a bunch of dark spots in the wire. however when I bend the wire, they move. its like the el is not working correctly. Not sure what the problem is. I may have to replace this piece. good thing is its only tucked in behind the trim work.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2330.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2328.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2336.jpg

Some night shots:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2338.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2333.jpg

FYI there are 3 el wires all together.

I should be able to finish the el wire around the window and isnstall the trim ring next. After that, I can concentrate on getting the resevoir mounted.

LOL, looking at these pictures, I just realized that I forgot to paint the rivits. DUH.

TTFN

[rendermandan]

I told you guys I would not let you down.

Here's a shot with the window installed. it doesn't sit as flat as I'd like it to. this is mainly due to the curved surface. If I had it to do over again, I would have prebent the trim piece before installing it. Oh well, I think it still looks good:

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2341.jpg

I laid out 3 60 deg lines so I could mark the resevoir brackets:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2345.jpg

then I just drilled some holes and cut out the padding on the inside for the head of the screw:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2346.jpg

I painted the supports black for now:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2354.jpg

here are both supports with the factory mounts cut off:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2356.jpg

I then drilled and tapped each support:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2358.jpg

And here they are with the supports mounted and ready to go:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2360.jpg

Installed on the resevoir:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2361.jpg

then I slid it into the tube. Very tight fit. I will have to go back and do a little touchup paint when I'm done:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2362.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2363.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2364.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2368.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2369.jpg

Then I installed the translucent side panels on the bottom:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2372.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2373.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2376.jpg

I fixed the issue with the tubes that come out of the resevoir. I cut some holes and made it work: :)
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2371.jpg

Just so you guys can see, the back part is packed full of wiring, 3 transformers, 2 fans and the radiator. I still have more to go!
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2377.jpg

I'm getting to the point of forcing myself to decide what to do on the back half. I'm still not sure yet....

[rendermandan]

Here is just a small update tonight.

My dad was adding some gutter helmut to his house so I snagged a piece. here is a section of it.

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2379.jpg

I ran to the hobby store and bought some plastic modeling parts so I could start some "kit basing". not really though. I'm building most of it from scratch.

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2381.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2384.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2385.jpg
sorry, not very exciting.

[rendermandan]

I continued with the kit bashing tonight. here are some pics.

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2390.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2391.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2393.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2396.jpg

[rendermandan]

Ok, I'm close to being done with the kit bashing.

Here are some Chrome wheels from a car kit my friend gave me. I thought they would make the perfect "Intakes" for the vents on the back. What do you think?

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2400.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2398.jpg

Here are the ones in the back. they look like a fan blade. Infact I think the model of the wheel was for an old style mustang and it was called "Turbine". Ironic huh?

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2404.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2409.jpg

Here is the kit bashing I did tonight on the other side:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2407.jpg

By the way, I'm not sure if you realize this or not but the top of this whole back comes off to access the radiator, fans and transformers.

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2405.jpg

Lastly, here is a shot looking at the end of the resevoir inside the tube. you can see the two holes I cut for the tubing directly below the barbs on the resevoir.

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2411.jpg

I hope I have enough room to install the tubing and get the clamps tight when I get around to it. :)

Up next. More painting, masking, painting, more masking, painting some more, masking........... You get the idea.

Later,

[rendermandan]

well, after alot of work, here is where I'm at:

Final shots of the Kit bashing:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2414.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2415.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2416.jpg

Then I started to mask stuff off and do some painting:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2419.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2421.jpg

Some more masking and painting:

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2422.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2423.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2424.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2429.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2430.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2437.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2431.jpg

then after some weathering with the drybrush, here are the results:

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2433.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2440.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2444.jpg

What do you guys think?

I'm just about done with this part of the mod. I have to get all the wiring soldered up and in order, then I can permenantly mount the resevoir with the tubing and afterward do some final paint touchups. but overall construction is almost done. Now I have to start planning out the case for this...

[rendermandan]

OK, last night I got some wiring done.

Here are some shots.

I installed everyting into the back housing and cut the wires to clean things up.

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2462.jpg

Then I soldered and heat shrinked them together.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2463.jpg

Everything goes to 2 molex connectors. One for the fans, (12v) and one for the leds and glow wire. (5V) -I didn't use the same plug because I want to be able to remove the radiator and fan assembly without having to cut any wires.

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2464.jpg

And now the obligitory night shots with all the lights on. -Note, I still don't have the led for the resevoir installed as I"m waiting on my sleeving.

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2466.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2467.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2468.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2469.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2470.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2471.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2472.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2473.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2478.jpg

And here it is with the lights on, but still running.

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2481.jpg

My hope is that when the tubing is filled with blue liquid, that the led in the resevoir will light it up. right now I just cut a piece of tubing to show you what it will look like. That is all I can do untill my sleeving comes tomorrow. :( By the way, have I ever mentioned I HATE FEDEX!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!

Later!

[rendermandan]

Ok, here is the stuff that arrived today.
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2489.jpg

I proceded to sleeve the led wire. (The only wire that may be seen on this mod by the way).
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2490.jpg

here it is installed:
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2491.jpg

Thats it. ITS DONE!!!!!
-I'm not going to set it up just yet. I still have the case to make.

[rendermandan]

Water Cooled Turbine Closing Images:

I'll let the images speak for themselves:

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2501.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2504.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2505.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2506.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2507.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2509.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2510.jpg

http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2492.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2493.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2511.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2512.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2514.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2515.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2516.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2517.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2518.jpg
http://i65.photobucket.com/albums/h205/rendermandan/Water%20Cooled%20Turbine/100_2519.jpg




Link To Original Worklog (http://www.thebestcasescenario.com/forum/showthread.php?t=9129)