Water Alien Rebirth

[pedrofilho]

Worklog of case mod I’ve started December, 22.12.2006 wich I intend to subscribe on the 2007 international CM Contest.
22.12.2006

Name: Water Alien Rebirth (i'll redo the Leadership Alien 3 Gamer case from zero, implementing water cooling)

HARDWARE CONFIG

MOBO A8N-E (COOLER MODED)
2048 DDR (COOLER MODED)
Athlon 64 4600X2
MSI NX7900GTX 512 (CM AQUAGATE-VIVA)
Audigy 2 ZS
2HDs 80GB Sata2 em Raid 0 - Samsung
DVD 111D Pioneer - DVD GSAH10A LG (CM Rounded UV Cable - Blue)

Case:

http://img01.picoodle.com/img/img01/6/12/21/f_gameralii_8bb9m_358a595f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_gameralii_8bb9m_358a595f.jpg)

Some instrumentals, materials and work photos
http://img01.picoodle.com/img/img01/6/12/21/f_PC210001i_8bb9m_eab4ca84.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210001i_8bb9m_eab4ca84.jpg)

http://img01.picoodle.com/img/img01/6/12/21/f_PC210005i_8bb9m_4cd22a7c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210005i_8bb9m_4cd22a7c.jpg)

http://img01.picoodle.com/img/img01/6/12/21/f_PC210007i_8bb9m_3eaf354a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210007i_8bb9m_3eaf354a.jpg)

http://img01.picoodle.com/img/img01/6/12/21/f_PC210002i_8bb9m_69286cb4.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210002i_8bb9m_69286cb4.jpg)

http://img01.picoodle.com/img/img01/6/12/21/f_PC210003i_8bb9m_c2851fb6.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210003i_8bb9m_c2851fb6.jpg)

http://img01.picoodle.com/img/img01/6/12/21/f_PC210005i_8bb9m_45c99a10.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210005i_8bb9m_45c99a10.jpg)

http://img01.picoodle.com/img/img01/6/12/21/f_PC210004i_8bb9m_3f2d5089.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210004i_8bb9m_3f2d5089.jpg)

http://img01.picoodle.com/img/img01/6/12/21/f_PC210011i_8bb9m_e0c6c6a0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210011i_8bb9m_e0c6c6a0.jpg)

http://img01.picoodle.com/img/img01/6/12/21/f_PC210008i_8bb9m_aaee7202.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210008i_8bb9m_aaee7202.jpg)

http://img01.picoodle.com/img/img01/6/12/21/f_PC210010i_8bb9m_76b1e7ca.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210010i_8bb9m_76b1e7ca.jpg)

http://img01.picoodle.com/img/img01/6/12/21/f_PC210002i_8bb9m_36f40ead.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210002i_8bb9m_36f40ead.jpg)

http://img01.picoodle.com/img/img01/6/12/21/f_PC210005i_8bb9m_f5a8daac.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210005i_8bb9m_f5a8daac.jpg)

http://img01.picoodle.com/img/img01/6/12/21/f_PC210007i_8bb9m_5582a7fc.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210007i_8bb9m_5582a7fc.jpg)

http://img01.picoodle.com/img/img01/6/12/21/f_PC210009i_8bb9m_0dc0f818.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210009i_8bb9m_0dc0f818.jpg)

http://img01.picoodle.com/img/img01/6/12/21/f_PC210010i_8bb9m_0846d31c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210010i_8bb9m_0846d31c.jpg)

http://img01.picoodle.com/img/img01/6/12/21/f_PC210002i_8bb9m_83d9d572.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210002i_8bb9m_83d9d572.jpg)

My Herbalife tea"Gás"
http://img01.picoodle.com/img/img01/6/12/21/f_PC210004i_8bb9m_7cc22207.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210004i_8bb9m_7cc22207.jpg)

Dremel Saw in action
http://img01.picoodle.com/img/img01/6/12/21/f_PC210005i_8bb9m_df34269b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210005i_8bb9m_df34269b.jpg)

Improvisation
http://img01.picoodle.com/img/img01/6/12/21/f_PC210006i_8bb9m_014a05c1.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210006i_8bb9m_014a05c1.jpg)

[pedrofilho]

After a Dremel sanding
http://img01.picoodle.com/img/img01/6/12/21/f_PC210011i_8bb9m_0ef47a8f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210011i_8bb9m_0ef47a8f.jpg)

My worktable, almost there.
http://img01.picoodle.com/img/img01/6/12/21/f_PC210001i_8bb9m_204c76c2.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210001i_8bb9m_204c76c2.jpg)

Notebook for the next updates:

http://img01.picoodle.com/img/img01/6/12/21/f_PC210001i_8bb9m_6502207e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/21/f_PC210001i_8bb9m_6502207e.jpg)

23.12.2006
Some other pictures

The table as i left yesterday
http://img01.picoodle.com/img/img01/6/12/22/f_PC220001i_e551m_68cae9ae.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220001i_e551m_68cae9ae.jpg)

Replacing nails for screws
http://img01.picoodle.com/img/img01/6/12/22/f_PC220004i_e551m_8da7c086.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220004i_e551m_8da7c086.jpg)

Suporting big screws
http://img01.picoodle.com/img/img01/6/12/22/f_PC220005i_e551m_9898aead.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220005i_e551m_9898aead.jpg)

For internal reinforcement
http://img01.picoodle.com/img/img01/6/12/22/f_PC220006i_e551m_c41858df.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220006i_e551m_c41858df.jpg)

Sand it with Dremel
http://img01.picoodle.com/img/img01/6/12/22/f_PC220001i_e551m_b93b051c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220001i_e551m_b93b051c.jpg)

Cutting the suport screws
http://img01.picoodle.com/img/img01/6/12/22/f_PC220008i_e551m_9d92f0f6.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220008i_e551m_9d92f0f6.jpg)

Just ready for a cleanner job. A lot of dust has flooded my room
http://img01.picoodle.com/img/img01/6/12/22/f_PC220001i_e551m_f047af71.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220001i_e551m_f047af71.jpg)

Some materials over the table and other are coming soon from e-bay.

The real case:
http://img01.picoodle.com/img/img01/6/12/22/f_PC220001i_e551m_cfff8edf.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220001i_e551m_cfff8edf.jpg)

http://img01.picoodle.com/img/img01/6/12/22/f_PC220003i_e551m_bf5a203b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220003i_e551m_bf5a203b.jpg)

http://img01.picoodle.com/img/img01/6/12/22/f_PC220010i_e551m_ac5f2c73.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220010i_e551m_ac5f2c73.jpg)

Nice mousepad, fine for hard pc working for long periods of time.
http://img01.picoodle.com/img/img01/6/12/22/f_PC220008i_e551m_cd7b1405.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220008i_e551m_cd7b1405.jpg)

This dragon will take a 2-3 days of hard engraving work, but it have to be done.
http://img01.picoodle.com/img/img01/6/12/22/f_PC220007i_e551m_3412e5ba.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220007i_e551m_3412e5ba.jpg)

‘Here we go
http://img01.picoodle.com/img/img01/6/12/22/f_PC220005i_e551m_dfa9b523.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220005i_e551m_dfa9b523.jpg)

http://img01.picoodle.com/img/img01/6/12/22/f_PC220006i_e551m_5220e90d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220006i_e551m_5220e90d.jpg)

Closer
http://img01.picoodle.com/img/img01/6/12/22/f_PC220007i_e551m_dc49f2b3.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220007i_e551m_dc49f2b3.jpg)

http://img01.picoodle.com/img/img01/6/12/22/f_PC220008i_e551m_31bdf6f4.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220008i_e551m_31bdf6f4.jpg)

Oops...
http://img01.picoodle.com/img/img01/6/12/22/f_PC220009i_e551m_a64ec1ef.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220009i_e551m_a64ec1ef.jpg)

The base.
http://img01.picoodle.com/img/img01/6/12/22/f_PC220001i_e551m_5114e7de.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220001i_e551m_5114e7de.jpg)

Materials (epóxi, fiberglass, polyester, PVC glue)
http://img01.picoodle.com/img/img01/6/12/22/f_PC220002i_e551m_fbeed957.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220002i_e551m_fbeed957.jpg)

Paints
http://img01.picoodle.com/img/img01/6/12/22/f_PC220003i_e551m_195e3848.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220003i_e551m_195e3848.jpg)

Aliens...
http://img01.picoodle.com/img/img01/6/12/22/f_PC220004i_e551m_d84e8d08.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220004i_e551m_d84e8d08.jpg)

A baby et ...
http://img01.picoodle.com/img/img01/6/12/22/f_PC220005i_e551m_b16a104e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220005i_e551m_b16a104e.jpg)

[pedrofilho]

Huge CNPS9700LED bought on e-Bay to CPU, the VGA cooler will be the Cooler Master Aquagate-viva
http://img01.picoodle.com/img/img01/6/12/22/f_PC220007i_e551m_983e80a2.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220007i_e551m_983e80a2.jpg)

New stuff
http://img01.picoodle.com/img/img01/6/12/22/f_PC220009i_e551m_8b25f5ce.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220009i_e551m_8b25f5ce.jpg)

For a professional cable sleeving mod on ST550EAG:
http://img01.picoodle.com/img/img01/6/12/22/f_PC220010i_e551m_cc0b5cd5.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220010i_e551m_cc0b5cd5.jpg)

Plastics
http://img01.picoodle.com/img/img01/6/12/22/f_PC220001i_e551m_c553fa4a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220001i_e551m_c553fa4a.jpg)

More plastics, for texturing (I’ll try a new technic, pay attention)
http://img01.picoodle.com/img/img01/6/12/22/f_PC220004i_e551m_d1c1db44.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/22/f_PC220004i_e551m_d1c1db44.jpg)

23.12.2006

Updates
http://img01.picoodle.com/img/img01/6/12/23/f_PC230002i_1d4dm_142eae67.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230002i_1d4dm_142eae67.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230003i_1d4dm_ed4ee47d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230003i_1d4dm_ed4ee47d.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230005i_1d4dm_b9c9177f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230005i_1d4dm_b9c9177f.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230008i_1d4dm_96e77af9.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230008i_1d4dm_96e77af9.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230002i_1d4dm_3180c422.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230002i_1d4dm_3180c422.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230004i_1d4dm_0d94c95f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230004i_1d4dm_0d94c95f.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230006i_1d4dm_dd272c3e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230006i_1d4dm_dd272c3e.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230009i_1d4dm_4f793a2a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230009i_1d4dm_4f793a2a.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230010i_1d4dm_6c62de00.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230010i_1d4dm_6c62de00.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230001i_1d4dm_01801a3d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230001i_1d4dm_01801a3d.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230002i_1d4dm_70b9883c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230002i_1d4dm_70b9883c.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230003i_1d4dm_a58bd901.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230003i_1d4dm_a58bd901.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230005i_1d4dm_f8396468.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230005i_1d4dm_f8396468.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230008i_1d4dm_b2e128a9.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230008i_1d4dm_b2e128a9.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230009i_1d4dm_f26b1c80.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230009i_1d4dm_f26b1c80.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230001i_1d4dm_288a14ac.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230001i_1d4dm_288a14ac.jpg)

I am deciding to paint the original cables of my ST550EAG, its very nice worked out, doesn’t need the full mod, just a paint and molex replacement.
http://img01.picoodle.com/img/img01/6/12/23/f_PC230005i_1d4dm_91306c13.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230005i_1d4dm_91306c13.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230006i_1d4dm_59d03793.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230006i_1d4dm_59d03793.jpg)

A 360º view
http://img01.picoodle.com/img/img01/6/12/23/f_PC230007i_1d4dm_74af0417.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230007i_1d4dm_74af0417.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230008i_1d4dm_cf6c96ff.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230008i_1d4dm_cf6c96ff.jpg)

[pedrofilho]

http://img01.picoodle.com/img/img01/6/12/23/f_PC230009i_1d4dm_be407635.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230009i_1d4dm_be407635.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230010i_1d4dm_5ccb947f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230010i_1d4dm_5ccb947f.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230001i_1d4dm_c14bb23f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230001i_1d4dm_c14bb23f.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230002i_1d4dm_f6559ac6.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230002i_1d4dm_f6559ac6.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230003i_1d4dm_47bc39e7.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230003i_1d4dm_47bc39e7.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230006i_1d4dm_660d6f43.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230006i_1d4dm_660d6f43.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230007i_1d4dm_b5b70d9e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230007i_1d4dm_b5b70d9e.jpg)

I’ll move the HDs case.
http://img01.picoodle.com/img/img01/6/12/23/f_PC230008i_1d4dm_4b171ea5.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230008i_1d4dm_4b171ea5.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230009i_1d4dm_2ccc9d0c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230009i_1d4dm_2ccc9d0c.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230011i_1d4dm_4e13af85.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230011i_1d4dm_4e13af85.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230012i_1d4dm_8d77ccbd.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230012i_1d4dm_8d77ccbd.jpg)

Holy Dremel
http://img01.picoodle.com/img/img01/6/12/23/f_PC230002i_1d4dm_483063ea.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230002i_1d4dm_483063ea.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230003i_1d4dm_1e110d40.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230003i_1d4dm_1e110d40.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230005i_1d4dm_9f8a7b46.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230005i_1d4dm_9f8a7b46.jpg)

http://img01.picoodle.com/img/img01/6/12/23/f_PC230006i_1d4dm_b6b6a4b5.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/23/f_PC230006i_1d4dm_b6b6a4b5.jpg)

25.12.2006

A little update
http://img01.picoodle.com/img/img01/6/12/25/f_PC250009i_51d5m_535e51a4.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/25/f_PC250009i_51d5m_535e51a4.jpg)

http://img01.picoodle.com/img/img01/6/12/25/f_PC250001i_51d5m_9476b5fe.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/25/f_PC250001i_51d5m_9476b5fe.jpg)

http://img01.picoodle.com/img/img01/6/12/25/f_PC250010i_51d5m_77f6e0ad.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/25/f_PC250010i_51d5m_77f6e0ad.jpg)

http://img01.picoodle.com/img/img01/6/12/25/f_PC250002i_51d5m_cb7b6009.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/25/f_PC250002i_51d5m_cb7b6009.jpg)

http://img01.picoodle.com/img/img01/6/12/25/f_PC250003i_51d5m_6d12fd24.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/25/f_PC250003i_51d5m_6d12fd24.jpg)

http://img01.picoodle.com/img/img01/6/12/25/f_PC250004i_51d5m_23220cbc.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/25/f_PC250004i_51d5m_23220cbc.jpg)

http://img01.picoodle.com/img/img01/6/12/25/f_PC250005i_51d5m_a1005a57.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/25/f_PC250005i_51d5m_a1005a57.jpg)

http://img01.picoodle.com/img/img01/6/12/25/f_PC250006i_51d5m_330496de.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/25/f_PC250006i_51d5m_330496de.jpg)

http://img01.picoodle.com/img/img01/6/12/25/f_PC250007i_51d5m_c6675d5b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/25/f_PC250007i_51d5m_c6675d5b.jpg)

24.12.2006
Today updates:

A beautiful day...
http://img01.picoodle.com/img/img01/6/12/27/f_PC270006i_3aadm_bdb38c53.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270006i_3aadm_bdb38c53.jpg)

[pedrofilho]

Chipset cooler mod
http://img01.picoodle.com/img/img01/6/12/27/f_PC270005i_3aadm_41d402d1.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270005i_3aadm_41d402d1.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270007i_3aadm_313a3fe4.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270007i_3aadm_313a3fe4.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270008i_3aadm_73b5d6d8.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270008i_3aadm_73b5d6d8.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270009i_3aadm_7398af01.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270009i_3aadm_7398af01.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270010i_3aadm_9a90d6e8.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270010i_3aadm_9a90d6e8.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270012i_3aadm_f1d81f8f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270012i_3aadm_f1d81f8f.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270001i_3aadm_bc944384.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270001i_3aadm_bc944384.jpg)

After a lot of sanding...
http://img01.picoodle.com/img/img01/6/12/27/f_PC270002i_3aadm_b1ddac4c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270002i_3aadm_b1ddac4c.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270004i_3aadm_77a1539b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270004i_3aadm_77a1539b.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270009i_3aadm_098c6d3e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270009i_3aadm_098c6d3e.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270011i_3aadm_c52b9164.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270011i_3aadm_c52b9164.jpg)

Working on de case base:
http://img01.picoodle.com/img/img01/6/12/27/f_PC270007i_3aadm_b96fc739.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270007i_3aadm_b96fc739.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270008i_3aadm_1b7b4a68.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270008i_3aadm_1b7b4a68.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270009i_3aadm_58dff36f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270009i_3aadm_58dff36f.jpg)

Put into Coreldraw and printed on adesive tranparency paper:
http://img01.picoodle.com/img/img01/6/12/27/f_PESi_3aadm_fe7383cc.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PESi_3aadm_fe7383cc.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270010i_3aadm_8c1746a9.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270010i_3aadm_8c1746a9.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270011i_3aadm_c9738ae1.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270011i_3aadm_c9738ae1.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270013i_3aadm_b474dec1.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270013i_3aadm_b474dec1.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270015i_3aadm_d156e65e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270015i_3aadm_d156e65e.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270002i_3aadm_3c2f150e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270002i_3aadm_3c2f150e.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270003i_3aadm_f0f9e649.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270003i_3aadm_f0f9e649.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270005i_3aadm_290a0cdf.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270005i_3aadm_290a0cdf.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270007i_3aadm_8d153c9a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270007i_3aadm_8d153c9a.jpg)

Without an apropriated bit i've bought but still don't get it here, i used a wrong bit and screw it up everything, this is the results...
http://img01.picoodle.com/img/img01/6/12/27/f_PC270008i_3aadm_c6959c92.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270008i_3aadm_c6959c92.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270009i_3aadm_3197d90e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270009i_3aadm_3197d90e.jpg)

[pedrofilho]

http://img01.picoodle.com/img/img01/6/12/27/f_PC270010i_3aadm_9c5a232e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270010i_3aadm_9c5a232e.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270011i_3aadm_7c856be2.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270011i_3aadm_7c856be2.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270012i_3aadm_216691ca.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270012i_3aadm_216691ca.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270008i_3aadm_1c92522f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270008i_3aadm_1c92522f.jpg)

http://img01.picoodle.com/img/img01/6/12/27/f_PC270009i_3aadm_135cf22e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/27/f_PC270009i_3aadm_135cf22e.jpg)

26.12.2006

Today i started the ST-550EAG MOD, and just realize their coolers are soft to replace, so i decide to replace de 92mm for a 120mm.

It was a hard work today, cutting with dremel and soffering with Dremel Router, but i learned something today and tomorow i'll work better. (i hope)

Photos
http://img01.picoodle.com/img/img01/6/12/29/f_PC290006i_24b6m_c0d441df.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290006i_24b6m_c0d441df.jpg)

http://img01.picoodle.com/img/img01/6/12/29/f_PC290007i_24b6m_d89a726d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290007i_24b6m_d89a726d.jpg)

http://img01.picoodle.com/img/img01/6/12/29/f_PC290010i_24b6m_940a3eca.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290010i_24b6m_940a3eca.jpg)

Breaking news... really !
http://img01.picoodle.com/img/img01/6/12/29/f_PC290012i_24b6m_2f83ad46.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290012i_24b6m_2f83ad46.jpg)

Cooler i'll change.
http://img01.picoodle.com/img/img01/6/12/29/f_PC290014i_24b6m_d21cf1f5.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290014i_24b6m_d21cf1f5.jpg)

Easy
http://img01.picoodle.com/img/img01/6/12/29/f_PC290015i_24b6m_c046d4c1.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290015i_24b6m_c046d4c1.jpg)

http://img01.picoodle.com/img/img01/6/12/29/f_PC290003i_24b6m_0f367946.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290003i_24b6m_0f367946.jpg)

http://img01.picoodle.com/img/img01/6/12/29/f_PC290004i_24b6m_59ed2e99.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290004i_24b6m_59ed2e99.jpg)

'Gas'
http://img01.picoodle.com/img/img01/6/12/29/f_PC290006i_24b6m_883e2a6f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290006i_24b6m_883e2a6f.jpg)

CM 2007, Here we are :)
http://img01.picoodle.com/img/img01/6/12/29/f_PC290008i_24b6m_d12350e2.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290008i_24b6m_d12350e2.jpg)

chip :shock: with Dremel
http://img01.picoodle.com/img/img01/6/12/29/f_PC290011i_24b6m_b9206724.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290011i_24b6m_b9206724.jpg)

http://img01.picoodle.com/img/img01/6/12/29/f_PC290012i_24b6m_0145f7de.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290012i_24b6m_0145f7de.jpg)

Sanding
http://img01.picoodle.com/img/img01/6/12/29/f_PC290008i_24b6m_6f616062.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290008i_24b6m_6f616062.jpg)

Cut done !
http://img01.picoodle.com/img/img01/6/12/29/f_PC290013i_24b6m_18fea4cc.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290013i_24b6m_18fea4cc.jpg)

Cutting plex-glass with Dremel saw maybe not a good idea (i'll use apropriate bit with router to redo de cut tomorrow)
http://img01.picoodle.com/img/img01/6/12/29/f_PC290015i_24b6m_fc448510.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290015i_24b6m_fc448510.jpg)

Learning...
http://img01.picoodle.com/img/img01/6/12/29/f_PC290017i_24b6m_912ec5f5.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290017i_24b6m_912ec5f5.jpg)

http://img01.picoodle.com/img/img01/6/12/29/f_PC290021i_24b6m_ce632d65.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290021i_24b6m_ce632d65.jpg)

Piece of... cant say !
http://img01.picoodle.com/img/img01/6/12/29/f_PC290022i_24b6m_192a3395.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290022i_24b6m_192a3395.jpg)

Trying
http://img01.picoodle.com/img/img01/6/12/29/f_PC290023i_24b6m_d6edda7a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/29/f_PC290023i_24b6m_d6edda7a.jpg)

.

[pedrofilho]

31.12.2006 / 01.01.2007

I decided doing some tests with leds ligthing before going on with the project.
http://img01.picoodle.com/img/img01/6/12/30/f_PC300007i_1d02m_12abc1d5.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/30/f_PC300007i_1d02m_12abc1d5.jpg)

http://img01.picoodle.com/img/img01/6/12/30/f_PC300010i_1d02m_d31823ce.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/30/f_PC300010i_1d02m_d31823ce.jpg)

http://img01.picoodle.com/img/img01/6/12/30/f_PC300014i_1d02m_b725715d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/30/f_PC300014i_1d02m_b725715d.jpg)

These rivets are for tests purpose only.
http://img01.picoodle.com/img/img01/6/12/30/f_PC300016i_1d02m_8ec61ce3.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/30/f_PC300016i_1d02m_8ec61ce3.jpg)

Seems the idea works
http://img01.picoodle.com/img/img01/6/12/30/f_PC300017i_1d02m_d1989620.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/30/f_PC300017i_1d02m_d1989620.jpg)

http://img01.picoodle.com/img/img01/6/12/30/f_PC300018i_1d02m_651c20a2.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/30/f_PC300018i_1d02m_651c20a2.jpg)

I was running up to do some soldering works when the UPS arrived, damn ! For one second i thought the CM WC had arrived, but was another Dremel I've bought to do engraving jobs(this one is diferent of mine because it start at 5000 rpm and goes to 35000, the other one i have goes from 10k rpm to 33k rpm)
http://img01.picoodle.com/img/img01/6/12/30/f_PC300001i_1d02m_b26d9fe9.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/30/f_PC300001i_1d02m_b26d9fe9.jpg)

http://img01.picoodle.com/img/img01/6/12/30/f_PC300003i_1d02m_abb1b286.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/30/f_PC300003i_1d02m_abb1b286.jpg)

http://img01.picoodle.com/img/img01/6/12/30/f_PC300005i_1d02m_6782e4b0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/30/f_PC300005i_1d02m_6782e4b0.jpg)

http://img01.picoodle.com/img/img01/6/12/30/f_PC300006i_1d02m_a791b5fb.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/30/f_PC300006i_1d02m_a791b5fb.jpg)

http://img01.picoodle.com/img/img01/6/12/30/f_PC300009i_1d02m_67d24f03.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/30/f_PC300009i_1d02m_67d24f03.jpg)

http://img01.picoodle.com/img/img01/6/12/30/f_PC300012i_1d02m_f19ca092.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/30/f_PC300012i_1d02m_f19ca092.jpg)

http://img01.picoodle.com/img/img01/6/12/30/f_PC300013i_1d02m_f8d9cc0a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/30/f_PC300013i_1d02m_f8d9cc0a.jpg)

http://img01.picoodle.com/img/img01/6/12/30/f_PC300015i_1d02m_8b577507.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/30/f_PC300015i_1d02m_8b577507.jpg)

Dark photos are not what i can do best...
http://img01.picoodle.com/img/img01/6/12/30/f_PC300016i_1d02m_fe145563.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/30/f_PC300016i_1d02m_fe145563.jpg)

Some news at the font modding... (still leaning to use the Dremel router, if anyone knows where i can find any kind of tutorial, please, tell me where)
http://img01.picoodle.com/img/img01/6/12/31/f_PC310009i_a553m_93b7c348.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/31/f_PC310009i_a553m_93b7c348.jpg)

Doing these borders results in a very nice finishing.
http://img01.picoodle.com/img/img01/6/12/31/f_PC310001i_a553m_868f6ae8.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/31/f_PC310001i_a553m_868f6ae8.jpg)

http://img01.picoodle.com/img/img01/6/12/31/f_PC310002i_a553m_275a9b52.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/31/f_PC310002i_a553m_275a9b52.jpg)

I reached out a very nice fit on this piece
http://img01.picoodle.com/img/img01/6/12/31/f_PC310004i_a553m_6faf4dcf.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/31/f_PC310004i_a553m_6faf4dcf.jpg)

Some hand sanding with 360, 600 and 1200 sands, respectivelly, to acomplish the final results...
http://img01.picoodle.com/img/img01/6/12/31/f_PC310007i_a553m_d038ba62.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/31/f_PC310007i_a553m_d038ba62.jpg)

Dust, dust2 and dust2007... :)
http://img01.picoodle.com/img/img01/6/12/31/f_PC310011i_a553m_921afdc1.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/31/f_PC310011i_a553m_921afdc1.jpg)

The concept:
http://img01.picoodle.com/img/img01/6/12/31/f_PC310012i_a553m_5e11950c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/31/f_PC310012i_a553m_5e11950c.jpg)

Now i'll do a 120mm hole at center of the top and put an nice one cooler with leds on with. (i'm thinking put blue light inside to contrast with red lights an red UV reactives i'll use inside de case.
http://img01.picoodle.com/img/img01/6/12/31/f_PC310015i_a553m_464a7d62.jpg (http://www.picoodle.com/view.php?srv=img01&img=/6/12/31/f_PC310015i_a553m_464a7d62.jpg)

It's all for now, i'll put more soon...

Coments are very wellcome...

See you and happy new year for everybody !

Pedro Torres

[pedrofilho]

Hi everyone,

I am working on a new font cover, because, i want to put a 120mm fan and the cover i've made do not have left enough space for it. (it's a very small font, i coudn't believe)

Look at that:
http://img02.picoodle.com/img/img02/7/1/2/f_P1020005i_4d73m_8ea7007a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/2/f_P1020005i_4d73m_8ea7007a.jpg)

Alson, today i've ordered a CM Dual Storm fan for the VGA memory chipsets that will changed when the CM Aquagate-viva arrives.

I want thanks to all of you for the coments you've made, they're very wellcome and makes me very proud. This also lets me believe i am doing something nice here.


Wow. This is looking truly amazing, my hat goes off to you. Great job so far, I'm looking forward to seeing more.

Thank you tybrenis, i proud to accept your eulogious references to my work! :D


Awesome, Keep up the work!

Thank you, i will !


I agree. Great work! +rep.

Thank you, sgtm !


This is a fantastic worklog with a lot of effort and great photography. Keep up the good work!

+Rep!

-Dave

Thank you Dave, i'm loving doind this, including taking work pictures...


Very nice table, i spy a razer mousepad, but wheres the mouse? i <3 mine

Seems like one, but it's not a joke, 'the mouse is on the table' ?! :)


Very nice mod, love the feet!
Thank you, i've walking a lot by hardware store to another 'till find this one... It will win a texturized paintig later...

That it for now, see you later...

And, again, thank you and very happy new year to all of you !

Pedro Torres

PS-> Sorry any english mystakes.

[pedrofilho]

Nice work so far, I am monitoring this one. I like the creativity here!

BTW: I notice you have your refreshments handy, What are you drinking?

It's a delicious and energetic herbalife tea... Really nice. :)


Welcome Pedro,
I agree with everything above, great worklog!
Jon

Thank you !

Today i got an item wich is essencial for this project, and will define some of the next steps and was what i was wainting for. It was delayed about 20 days by brazilian aduana services...
http://img02.picoodle.com/img/img02/7/1/4/f_P1040003i_f084m_fe3470b1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/4/f_P1040003i_f084m_fe3470b1.jpg)

I consider it one of the bigger conquest to my project, because this is the most important reason i am doing the mod, to cool down the system and let it more stable, besides the beautifull look and fantastic performance of Zalman CNPS9700LED.

This cooler is very compact and many says it really works... bought it for a reasonable price but was hard to find it, so, i bought somehow at e-Bay and wait a lot 'till put my hands on it.

Some pictures:
http://img02.picoodle.com/img/img02/7/1/4/f_P1040006i_f084m_001aa079.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/4/f_P1040006i_f084m_001aa079.jpg)

http://img02.picoodle.com/img/img02/7/1/4/f_P1040009i_f084m_c968e3f0.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/4/f_P1040009i_f084m_c968e3f0.jpg)

http://img02.picoodle.com/img/img02/7/1/4/f_P1040011i_f084m_020ba29b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/4/f_P1040011i_f084m_020ba29b.jpg)

http://img02.picoodle.com/img/img02/7/1/4/f_P1040012i_f084m_17dc57c2.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/4/f_P1040012i_f084m_17dc57c2.jpg)

http://img02.picoodle.com/img/img02/7/1/4/f_P1040008i_f084m_73a5b23d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/4/f_P1040008i_f084m_73a5b23d.jpg)

http://img02.picoodle.com/img/img02/7/1/4/f_P1040013i_f084m_a242e577.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/4/f_P1040013i_f084m_a242e577.jpg)

http://img02.picoodle.com/img/img02/7/1/4/f_P1040014i_f084m_a04897d3.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/4/f_P1040014i_f084m_a04897d3.jpg)

Now, with theese CM WC in hands, i'll decide where to install it and will next it do some cuts in front panel and other parts of case.

I hope to rear some words of others owners of this WC, most of then, general tooks about it.

I found it absolutely amazing. Very well designed and finished, it is a small piece of art and technology, no doubts about... The only "to do" thing is, maybe, a lapping on block to add some shinny, what you folks think about it?!

Thank you for the coments, see you soon !

Pedro Torres.

[pedrofilho]

Today i removed the foots that will be fixed with screws later and did some cuts behind the case to do a small widows that allow light to pass by.

While cutting, i got these 2 smal tanks models that will be used in some exterior textures details. I am wainting the airbrush arrive here to start painting some exterior parts.

The tanks:
http://img02.picoodle.com/img/img02/7/1/5/f_P1050002i_27e3m_fd0b10c6.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/5/f_P1050002i_27e3m_fd0b10c6.jpg)

Pieces:
http://img02.picoodle.com/img/img02/7/1/5/f_P1050003i_27e3m_9b53e19a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/5/f_P1050003i_27e3m_9b53e19a.jpg)

Small window for light pass trought...
http://img02.picoodle.com/img/img02/7/1/5/f_P1050006i_27e3m_12700a1b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/5/f_P1050006i_27e3m_12700a1b.jpg)

Cuted:
http://img02.picoodle.com/img/img02/7/1/5/f_P1050007i_27e3m_15081e84.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/5/f_P1050007i_27e3m_15081e84.jpg)

Some sanding to revel the cut imperfections.
http://img02.picoodle.com/img/img02/7/1/5/f_P1050011i_27e3m_48d6b83a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/5/f_P1050011i_27e3m_48d6b83a.jpg)

After a hard sanding, this result:
http://img02.picoodle.com/img/img02/7/1/5/f_P1050013i_27e3m_313c78fa.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/5/f_P1050013i_27e3m_313c78fa.jpg)

As i spected the WC is small and will fit in that space left by HDs.

Tomorrow i'll do their cuts and for small ET instalation. Also, i'll start some fiberglass working...

Thank you for beeing here,

Pedro Torres.

[pedrofilho]

Today updates:
http://img02.picoodle.com/img/img02/7/1/6/f_P1060004i_c50bm_b6ad1e8d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060004i_c50bm_b6ad1e8d.jpg)

http://img02.picoodle.com/img/img02/7/1/6/f_P1060005i_c50bm_66d2d041.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060005i_c50bm_66d2d041.jpg)

http://img02.picoodle.com/img/img02/7/1/6/f_P1060006i_c50bm_dd4fb97f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060006i_c50bm_dd4fb97f.jpg)

http://img02.picoodle.com/img/img02/7/1/6/f_P1060007i_c50bm_8e12696a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060007i_c50bm_8e12696a.jpg)

After some sanding work...
http://img02.picoodle.com/img/img02/7/1/6/f_P1060010i_c50bm_6f1c4888.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060010i_c50bm_6f1c4888.jpg)

Testing...
http://img02.picoodle.com/img/img02/7/1/6/f_P1060013i_c50bm_2ddd3633.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060013i_c50bm_2ddd3633.jpg)

Plexi-glass work to back side window:
http://img02.picoodle.com/img/img02/7/1/6/f_P1060015i_c50bm_eaf7bf97.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060015i_c50bm_eaf7bf97.jpg)

Cut and borders made with Dremel router:
http://img02.picoodle.com/img/img02/7/1/6/f_P1060016i_c50bm_94525229.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060016i_c50bm_94525229.jpg)

After some sanding...
http://img02.picoodle.com/img/img02/7/1/6/f_P1060002i_c50bm_a0994cb0.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060002i_c50bm_a0994cb0.jpg)

I don't liked the result, then, tomorrow i'll do it again.
http://img02.picoodle.com/img/img02/7/1/6/f_P1060005i_c50bm_69c6bd04.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060005i_c50bm_69c6bd04.jpg)

Tomorrou i'll capture the ET form with fiberglass

Attempting Alfa 1.0
http://img02.picoodle.com/img/img02/7/1/6/f_P1060003i_a2a1m_c89a478f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060003i_a2a1m_c89a478f.jpg)

http://img02.picoodle.com/img/img02/7/1/6/f_P1060004i_a2a1m_0858336a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060004i_a2a1m_0858336a.jpg)

http://img02.picoodle.com/img/img02/7/1/6/f_P1060009i_a2a1m_3478d57a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060009i_a2a1m_3478d57a.jpg)

http://img02.picoodle.com/img/img02/7/1/6/f_P1060011i_a2a1m_0ac6872c.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060011i_a2a1m_0ac6872c.jpg)

http://img02.picoodle.com/img/img02/7/1/6/f_P1060013i_a2a1m_30bb859a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060013i_a2a1m_30bb859a.jpg)

http://img02.picoodle.com/img/img02/7/1/6/f_P1060014i_a2a1m_281b8b4f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060014i_a2a1m_281b8b4f.jpg)

http://img02.picoodle.com/img/img02/7/1/6/f_P1060015i_a2a1m_b6cc640f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060015i_a2a1m_b6cc640f.jpg)

http://img02.picoodle.com/img/img02/7/1/6/f_P1060016i_a2a1m_9125ff8d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060016i_a2a1m_9125ff8d.jpg)

Capturing the ET oval face form:
http://img02.picoodle.com/img/img02/7/1/6/f_P1060017i_a2a1m_376dca9b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060017i_a2a1m_376dca9b.jpg)

I dit it 3 times and put all together with soft tape.
http://img02.picoodle.com/img/img02/7/1/6/f_P1060018i_a2a1m_fbcbcfb2.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060018i_a2a1m_fbcbcfb2.jpg)

Exed...
http://img02.picoodle.com/img/img02/7/1/6/f_P1060001i_a2a1m_a4948df0.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060001i_a2a1m_a4948df0.jpg)

Now is to put the polyester resin and fiberglass tocapture the ET face form
http://img02.picoodle.com/img/img02/7/1/6/f_P1060002i_a2a1m_3d432f3c.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/6/f_P1060002i_a2a1m_3d432f3c.jpg)

See you tomorrow

Pedro Torres.
Tomorrow i'll really start that fiberglass work i told before.

Thank you for beeing here !

Pedro Torres.

[pedrofilho]

Can't wait for the fiberglass work.

Great worklog. Great pics.


Thank you Commando, casemoding is a very nice hobby i've start and i'm really loving to do it, but, every coments like this yours, makes me want do ever the best i can.

This was my first time with fiberglass and i learned a lot. I did this form capturing first because it doen't need best results, than, i made use of this moment to learn.

Thank you for your coment !

Today updates (A):

Finelly, some updates with fiberglass works, that i loved to working with:
http://img02.picoodle.com/img/img02/7/1/7/f_P1070006i_b64bm_172712e6.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070006i_b64bm_172712e6.jpg)

http://img02.picoodle.com/img/img02/7/1/7/f_P1070009i_b64bm_2ccf3b87.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070009i_b64bm_2ccf3b87.jpg)

http://img02.picoodle.com/img/img02/7/1/7/f_P1070012i_b64bm_1da8c7fc.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070012i_b64bm_1da8c7fc.jpg)

http://img02.picoodle.com/img/img02/7/1/7/f_P1070013i_b64bm_3a60f0b4.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070013i_b64bm_3a60f0b4.jpg)

http://img02.picoodle.com/img/img02/7/1/7/f_P1070015i_b64bm_67bab0d5.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070015i_b64bm_67bab0d5.jpg)

http://img02.picoodle.com/img/img02/7/1/7/f_P1070016i_b64bm_f5662454.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070016i_b64bm_f5662454.jpg)

http://img02.picoodle.com/img/img02/7/1/7/f_P1070017i_b64bm_64f6d174.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070017i_b64bm_64f6d174.jpg)

Did all work over a plastic and used dispendeable materials, making thiks easy to clean up after ;)
http://img02.picoodle.com/img/img02/7/1/7/f_P1070018i_b64bm_ae97091b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070018i_b64bm_ae97091b.jpg)

More important of all that, the apropriate mask ;)
http://img02.picoodle.com/img/img02/7/1/7/f_P1070002i_b64bm_f14e5b92.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070002i_b64bm_f14e5b92.jpg)

Touching test done, it's almost dry..
http://img02.picoodle.com/img/img02/7/1/7/f_P1070003i_b64bm_49098614.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070003i_b64bm_49098614.jpg)

Removing the piece, next time i work with fiberglass i'll use only tape instead using alumin laminate paper 'cause it's very easy to remove:
http://img02.picoodle.com/img/img02/7/1/7/f_P1070001i_86c2m_9a7f488c.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070001i_86c2m_9a7f488c.jpg)

As this is just for modeling the plexi-glass, i think it's enough, but, to for some detailed work, it is not apropriated. (first time i used fiberglass, what emotion... :D )
http://img02.picoodle.com/img/img02/7/1/7/f_P1070002i_86c2m_1be69026.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070002i_86c2m_1be69026.jpg)

Quite enough (just cut the borders to be nice and it's done):
http://img02.picoodle.com/img/img02/7/1/7/f_P1070005i_86c2m_da93ceb6.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070005i_86c2m_da93ceb6.jpg)

Thank you for beeing here.

Pedro Torres.

[pedrofilho]

Ooooo....fiberglass...
I've always wanted to learn how to build with that stuff, I have a subwoofer box built into my trunk with it that was custom made and I really wanted to stick around to see how it was done but had to work. Looks like you figured it out quite well, great job! This project is great reading!!!

I think this is the best think on casemoding, the learning... Glad you learned something with this worklog.

Thanks !


woooww damn nice work with the F/G
can't wayt to see what's next :D

+rep

This week i'll buy a thermal blower to print the ET figure on plexi-glass and give a 3d aspect to it.

Thanks !

The next pictures i've worked on photopaint to let it lighter to load... :)

Just cutted the borders:
http://img02.picoodle.com/img/img02/7/1/8/f_P1080020i_e795m_9e48e006.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/8/f_P1080020i_e795m_9e48e006.jpg)


Cut on front panel where i'll place de little ET.
http://img02.picoodle.com/img/img02/7/1/7/f_P1070006i_79dfm_4c4bc3d7.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070006i_79dfm_4c4bc3d7.jpg)

http://img02.picoodle.com/img/img02/7/1/7/f_P1070004i_79dfm_78881177.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070004i_79dfm_78881177.jpg)

http://img02.picoodle.com/img/img02/7/1/7/f_P1070002i_79dfm_84db11e3.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/7/f_P1070002i_79dfm_84db11e3.jpg)

Getting ready to fix the leds on base hexagons
http://img02.picoodle.com/img/img02/7/1/8/f_P1080018i_e795m_b6c13197.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/8/f_P1080018i_e795m_b6c13197.jpg)

Seems i'll make some money tomorrow at afternoon to buy the thermal blower i need to do some plexi-glass and other plastics works.

See you later,

Pedro Torres.

[pedrofilho]

Your fabrication skills are top notch! Also your attention to detail is a lesson for us all. Keep working and you will be sure to win the competition.


Thank you simon275,

Today i learned something else when tried to do a circular depression on foot bases, look:

I did this circular depression on hexagons to the leds lights go directly to the borders, increasing it's ligh efect.

Also, i got the airbrush, wich i'll use to paint the external textures.

Now, i am depending of thermal blower to start huges updates.

Today's some processed pictures (hope get ligther to load it):
http://img02.picoodle.com/img/img02/7/1/9/f_P1090002i_f198m_c0f49db6.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/9/f_P1090002i_f198m_c0f49db6.jpg)

S* happens... i've lost one of hexagons because used a wrong Dremel bit and solve this using correct tecnique, watch this: http://img02.picoodle.com/img/img02/7/1/9/f_P1090004i_f198m_f2d5109b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/9/f_P1090004i_f198m_f2d5109b.jpg)

http://img02.picoodle.com/img/img02/7/1/9/f_P1090005i_f198m_72107279.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/9/f_P1090005i_f198m_72107279.jpg)

http://img02.picoodle.com/img/img02/7/1/9/f_P1090006i_f198m_2a74d421.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/9/f_P1090006i_f198m_2a74d421.jpg)

http://img02.picoodle.com/img/img02/7/1/9/f_P1090007i_f198m_bb13a9fb.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/9/f_P1090007i_f198m_bb13a9fb.jpg)

http://img02.picoodle.com/img/img02/7/1/9/f_P1090008i_f198m_a69b4681.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/9/f_P1090008i_f198m_a69b4681.jpg)

http://img02.picoodle.com/img/img02/7/1/9/f_P1090009i_f198m_c9a58296.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/9/f_P1090009i_f198m_c9a58296.jpg)

http://img02.picoodle.com/img/img02/7/1/9/f_P1090010i_f198m_011b8320.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/9/f_P1090010i_f198m_011b8320.jpg)

One ready base to acomplish the leds:
http://img02.picoodle.com/img/img02/7/1/9/f_P1090006i_f198m_9dcf421c.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/9/f_P1090006i_f198m_9dcf421c.jpg)

The airbrush (it was the cheaper i've found, but, seems it will work just fine - at least, i've already crossed the fingers)
http://img02.picoodle.com/img/img02/7/1/9/f_P1090003i_f198m_c61a57f5.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/9/f_P1090003i_f198m_c61a57f5.jpg)

Thanks folks, i'll do an effort to get the thermal blower tomorrow to start a true job here.

See you,

Pedro Torres.

[pedrofilho]

Fantastic work log, Pedro!

How do you like the Dremel router? I've been trying to decide whether to get that or the Dremel router table (or a full sized router table). Also, were you using the Dremel saw to cut your plexi?

Again, great work.

Hello javafiend,

I think the router i have is easier to operate. It's easy to change the bits and is not fixed, so you can rotate it, instead rotatind the material you're working on it. (have i made myself clear?)

To cut the plexi i use the saw to do long cuts, because it's fast and do strait cuts. To do short cuts, i use the Dremel cut disk - the thin 409 piece, because it results in less dust, but, produces a toxic smoke, so i have to use a not confortable anti-organic mask.

This router, with the apropriate bit, can do fine works on plexi, wood, and a lot of materials, and you can define the deep of cut, for example, it's really an amazin stuff.

(*Dremel is not paying me to do this comercial :D) - yet !

Thank you for beeing here, hope i could help.

Some picts of a small update from today's work, including, the fabrication of 2 new hexagons that i've to cut again.
http://img02.picoodle.com/img/img02/7/1/10/f_P1100003i_a27cm_c7e2dc7a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/10/f_P1100003i_a27cm_c7e2dc7a.jpg)

Did a finishing job on back side window and other sanding works, nothing relevant work today. Tomorrow will have some significant updates, i hope.. :)
http://img02.picoodle.com/img/img02/7/1/10/f_P1100002i_a7cdm_6d875bea.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/10/f_P1100002i_a7cdm_6d875bea.jpg)

This will result in a better fit of plexi-glass:
http://img02.picoodle.com/img/img02/7/1/10/f_P1100006i_a7cdm_547cafc2.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/10/f_P1100006i_a7cdm_547cafc2.jpg)

See you people,

Pedro Torres.

[pedrofilho]

Brilliant Pedro. This worklog is wicked. Top pics and I can't wait to see more. Keep it up kiddo:up:

Thank you for your coment, tomorrow will have some hard work.

See you...


Wow man, excellent work. I love the case feet you made, and great job with the fiberglass! And I love all the pics! It gives great detail into what you're doing.

Thank you Maleficus, i've made a small update on lightning base feet hexagons.

Yor coments are aways very wellcome, thank you !

I got today the light efect i was looking for. To show it better i've to do a small movie of hexagons and leds it in action.

That is a lot of light and is exactly what i want, to give the impression that the case is floating over lights, like a spacecraft...

http://www.youtube.com/watch?v=wQA4FrEjaDM

Some pics:
http://img02.picoodle.com/img/img02/7/1/10/f_P1100002i_523fm_af00c7d9.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/10/f_P1100002i_523fm_af00c7d9.jpg)

http://img02.picoodle.com/img/img02/7/1/10/f_P1100004i_523fm_55e2a8d1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/10/f_P1100004i_523fm_55e2a8d1.jpg)

Indeed lights. It apears ever when flash is used, amazing look:
http://img02.picoodle.com/img/img02/7/1/10/f_P1100012i_523fm_56fed6b4.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/10/f_P1100012i_523fm_56fed6b4.jpg)

I am going to sleep, 'cause i'm very tired.

Thank you all !

Pedro Torres.

[pedrofilho]

I did a small back panel to mobo no plexiglass:
http://img02.picoodle.com/img/img02/7/1/11/f_P1110001i_4baem_fcf997ab.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/11/f_P1110001i_4baem_fcf997ab.jpg)

http://img02.picoodle.com/img/img02/7/1/11/f_P1110003i_4baem_aafbe895.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/11/f_P1110003i_4baem_aafbe895.jpg)

http://img02.picoodle.com/img/img02/7/1/11/f_P1110006i_4baem_da1d0dfd.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/11/f_P1110006i_4baem_da1d0dfd.jpg)

Received this P-72 plastic model for external texturing job:
http://img02.picoodle.com/img/img02/7/1/11/f_P1110007i_4baem_3ef870d9.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/11/f_P1110007i_4baem_3ef870d9.jpg)

http://img02.picoodle.com/img/img02/7/1/11/f_P1110008i_4baem_e88e56ff.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/11/f_P1110008i_4baem_e88e56ff.jpg)

And,

Finelly i've got that heatgun:
http://img02.picoodle.com/img/img02/7/1/12/f_P1120002i_b557m_d1db51e9.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/12/f_P1120002i_b557m_d1db51e9.jpg)

http://img02.picoodle.com/img/img02/7/1/12/f_P1120004i_b557m_25d7eaf3.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/12/f_P1120004i_b557m_25d7eaf3.jpg)

Things will happen
http://img02.picoodle.com/img/img02/7/1/12/f_P1120006i_b557m_45b131b2.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/12/f_P1120006i_b557m_45b131b2.jpg)

Thank you people,

See you soon, with big news !

Pedro Torres.

[pedrofilho]

First results. Tomorrow i'll do a finishing job on ET and bring new fotos at daylight, theese are not very well.
http://img02.picoodle.com/img/img02/7/1/12/f_P1120004i_4d91m_1bf7ae30.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/12/f_P1120004i_4d91m_1bf7ae30.jpg)

http://img02.picoodle.com/img/img02/7/1/12/f_P1130006i_4d91m_90e78431.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/12/f_P1130006i_4d91m_90e78431.jpg)

http://img02.picoodle.com/img/img02/7/1/12/f_P1130007i_4d91m_ecbcdfcb.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/12/f_P1130007i_4d91m_ecbcdfcb.jpg)

http://img02.picoodle.com/img/img02/7/1/12/f_P1130008i_4d91m_8867e085.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/12/f_P1130008i_4d91m_8867e085.jpg)

That's all for this moment !

Pedro Torres.

[pedrofilho]

window looks wery well man
great update


+rep

Thank you !

Today news:

I got a little busy this week and the project got a delay wich i hope to compensate it with a tomorrow big update i am working on.

Some pics of today work and some materials i bought:
http://img02.picoodle.com/img/img02/7/1/17/f_P1170001i_d2f3m_9eaa10b6.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/17/f_P1170001i_d2f3m_9eaa10b6.jpg)

http://img02.picoodle.com/img/img02/7/1/17/f_P1170002i_d2f3m_855df4db.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/17/f_P1170002i_d2f3m_855df4db.jpg)

http://img02.picoodle.com/img/img02/7/1/17/f_P1170009i_d2f3m_6ca9720a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/17/f_P1170009i_d2f3m_6ca9720a.jpg)

http://img02.picoodle.com/img/img02/7/1/17/f_P1170001i_d2f3m_f06e9667.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/17/f_P1170001i_d2f3m_f06e9667.jpg)

http://img02.picoodle.com/img/img02/7/1/17/f_P1170004i_d2f3m_84a885db.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/17/f_P1170004i_d2f3m_84a885db.jpg)

The ET face deep is just fine, tomorrow i'll do a little blondo job on it and will finelly print the ET face on 3mm UV plexiglass.
http://img02.picoodle.com/img/img02/7/1/17/f_P1170007i_d2f3m_32ebdd54.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/17/f_P1170007i_d2f3m_32ebdd54.jpg)

See you tomorrow with a really nice update,

Pedro Torres.

[pedrofilho]

I shudder to think that chloroform is still being used. nonetheless useful, just a little more toxic than most.

This material is sold under a rigorous control system at medical / surgery store. I am a lawer and also could buy it.

It's 'till better material to do plexiglass soldering works, as the plexi seller said.

I'll use it carefully, dressing gloves, gas mask and glasses.

Thank's for your advice.


This is a fantastic worklog Pedro. It is quite inspirational. Thanks and well done. Cant wait for the further updates!

Thank you Intrace. I really apreciate your coments, you're wellcome.


Cant wait, woke up earlier for it.... :D

Couldn't do it, but i am going to bed later too. :p

Thank you !

Finished something and started another one:
http://img02.picoodle.com/img/img02/7/1/18/f_P1180002i_4eddm_c33e851.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/18/f_P1180002i_4eddm_c33e851.jpg)

http://img02.picoodle.com/img/img02/7/1/18/f_P1180005i_4eddm_307aa3b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/18/f_P1180005i_4eddm_307aa3b.jpg)

http://img02.picoodle.com/img/img02/7/1/18/f_P1180011i_4eddm_aaf3b16.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/18/f_P1180011i_4eddm_aaf3b16.jpg)

http://img02.picoodle.com/img/img02/7/1/18/f_P1180012i_4eddm_98985cc.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/18/f_P1180012i_4eddm_98985cc.jpg)

http://img02.picoodle.com/img/img02/7/1/18/f_P1180002i_4eddm_05dfff7.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/18/f_P1180002i_4eddm_05dfff7.jpg)

http://img02.picoodle.com/img/img02/7/1/18/f_P1180004i_4eddm_3576d50.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/18/f_P1180004i_4eddm_3576d50.jpg)

http://img02.picoodle.com/img/img02/7/1/18/f_P1180006i_4eddm_fc288cc.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/18/f_P1180006i_4eddm_fc288cc.jpg)

New stuff (got amazing):
http://img02.picoodle.com/img/img02/7/1/18/f_P1180013i_4eddm_58d861d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/18/f_P1180013i_4eddm_58d861d.jpg)

http://img02.picoodle.com/img/img02/7/1/18/f_P1180014i_4eddm_12b724f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/18/f_P1180014i_4eddm_12b724f.jpg)

Font cover begins:
http://img02.picoodle.com/img/img02/7/1/18/f_P1190004i_4eddm_34fc01f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/18/f_P1190004i_4eddm_34fc01f.jpg)

http://img02.picoodle.com/img/img02/7/1/18/f_P1190007i_4eddm_04f5603.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/18/f_P1190007i_4eddm_04f5603.jpg)

Tomorrow i'll post more photos and do some coments of works. I am really tired now !

That's all folks !

Pedro Torres.

[pedrofilho]

First of all, sorry for delay on updates... I am a busy modder that become a lawer on free time :P


the plexi looks much better nice work.

This give-me a lot of work, but it worsth the effort (did it 3 times). I liked the result too.

Thank you !


Neat plexi work. I think something that would go neat would be a coolant reservoir in the plexi bubble on the side.

You give a shot really near the idea i have. I intend to put this reservoir on front panel, using the smal ET. I am having trouble finding the plexi tube to replace the original glass case of little ET.

The hole idea is seems like you told.

Thank you, for your suggestion !


to get the lighted ring you should use a hole saw and a drill press, without the guide bit.
Good luck!

I already thoke how do it and this you told is the way i found better, but, i'll do a first hole with a hole saw with his bit, than, use the first hole as a guide to others, withou de bit. When tried do directly, it 'dances' over hard plexi. :p

Thank you for this tip, really nice one.



That's a great piece of work on the plexi. Keep up the great worklog, this is really excellent.

-Dave

Thank you, i am doing the best i can. And sometimes, i have to do one piece, 2-3 times 'till get the result i spect. But the great deal is the learning process and friendship you conquest, it's the amazing thing.

Thank you !

This Weekend, i started some things on front panel and did the font case (it's almost finished).
http://img01.picoodle.com/img/img01/7/1/20/f_P1200001i_3c11m_986aafc.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/20/f_P1200001i_3c11m_986aafc.jpg)

http://img01.picoodle.com/img/img01/7/1/20/f_P1200004i_3c11m_b24b6a8.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/20/f_P1200004i_3c11m_b24b6a8.jpg)

http://img01.picoodle.com/img/img01/7/1/20/f_P1200007i_3c11m_d7310a0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/20/f_P1200007i_3c11m_d7310a0.jpg)

http://img02.picoodle.com/img/img02/7/1/20/f_P1200003i_3c11m_e10d64d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/20/f_P1200003i_3c11m_e10d64d.jpg)

http://img01.picoodle.com/img/img01/7/1/20/f_P1200001i_3c11m_83618d0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/20/f_P1200001i_3c11m_83618d0.jpg)

Really hard work sanding (hope win that simbol to hard work :P)
http://img01.picoodle.com/img/img01/7/1/20/f_P1200002i_3c11m_a457e33.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/20/f_P1200002i_3c11m_a457e33.jpg)

Results as expected, very nice:
http://img02.picoodle.com/img/img02/7/1/20/f_P1200006i_3c11m_9445ae4.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/20/f_P1200006i_3c11m_9445ae4.jpg)

Almost there, with motherboard screws to font don't touch plexi directly:
http://img02.picoodle.com/img/img02/7/1/22/f_P1210002i_3023m_5fd964e.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/22/f_P1210002i_3023m_5fd964e.jpg)

This was how i did the holes, but, i did it another time to get final shape:
http://img02.picoodle.com/img/img02/7/1/22/f_P1210004i_3023m_98d44f1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/22/f_P1210004i_3023m_98d44f1.jpg)

http://img01.picoodle.com/img/img01/7/1/22/f_P1220007i_3023m_111e42a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/22/f_P1220007i_3023m_111e42a.jpg)

Clorof&#243;rmio is really very easy to work, not so toxic as i imagine, and fix the plexi easly, fast and stronger, watch:
http://img01.picoodle.com/img/img01/7/1/22/f_novo1i_3023m_3a271e1.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/22/f_novo1i_3023m_3a271e1.jpg)

http://img02.picoodle.com/img/img02/7/1/22/f_P1220011i_3023m_202f333.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/22/f_P1220011i_3023m_202f333.jpg)

The back panel of font i told did it twice (final result):
http://img02.picoodle.com/img/img02/7/1/22/f_P1220004i_3023m_6dd2c69.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/22/f_P1220004i_3023m_6dd2c69.jpg)

The measurements was perfect, the fun fits very nice, about 3mm over the font components, really nice:
http://img02.picoodle.com/img/img02/7/1/22/f_P1220005i_3023m_924f5fb.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/22/f_P1220005i_3023m_924f5fb.jpg)

Tomorow i'll finish it.

See you and sorry about delay, i am a modder that become a lawer at free time :D

Thank you !

Pedro Torres.

[pedrofilho]

More font case work photos :
http://img02.picoodle.com/img/img02/7/1/22/f_P1210002i_3023m_5fd964e.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/22/f_P1210002i_3023m_5fd964e.jpg)

Some materials...
http://img02.picoodle.com/img/img02/7/1/24/f_P1230001i_436cm_70bd8ea.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/24/f_P1230001i_436cm_70bd8ea.jpg)

To VGA WC reservoir i'll do with little ET on tube:
http://img01.picoodle.com/img/img01/7/1/24/f_P1240002i_436cm_230822e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/24/f_P1240002i_436cm_230822e.jpg)

Lots of work, just to fit the on/off key for the outside:
http://img02.picoodle.com/img/img02/7/1/24/f_P1240003i_436cm_b8ba75f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/24/f_P1240003i_436cm_b8ba75f.jpg)

http://img02.picoodle.com/img/img02/7/1/24/f_P1240002i_436cm_39aa331.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/24/f_P1240002i_436cm_39aa331.jpg)

http://img02.picoodle.com/img/img02/7/1/24/f_P1240003i_436cm_5eaa561.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/24/f_P1240003i_436cm_5eaa561.jpg)

http://img01.picoodle.com/img/img01/7/1/24/f_P1240005i_436cm_a6f3465.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/24/f_P1240005i_436cm_a6f3465.jpg)

Some work before finish the mounting process
http://img02.picoodle.com/img/img02/7/1/24/f_P1240004i_436cm_99edd87.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/24/f_P1240004i_436cm_99edd87.jpg)

Dremel router at work...
http://img01.picoodle.com/img/img01/7/1/24/f_P1240007i_436cm_0e53300.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/24/f_P1240007i_436cm_0e53300.jpg)

http://img01.picoodle.com/img/img01/7/1/24/f_P1240008i_436cm_584df66.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/24/f_P1240008i_436cm_584df66.jpg)

http://img02.picoodle.com/img/img02/7/1/24/f_P1240009i_436cm_5f3b116.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/24/f_P1240009i_436cm_5f3b116.jpg)

http://img01.picoodle.com/img/img01/7/1/24/f_P1240010i_436cm_da9d972.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/24/f_P1240010i_436cm_da9d972.jpg)

Done:
http://img02.picoodle.com/img/img02/7/1/24/f_P1240011i_436cm_8ed1fa1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/24/f_P1240011i_436cm_8ed1fa1.jpg)

Changing the internal cooler conector...
http://img02.picoodle.com/img/img02/7/1/24/f_P1240005i_436cm_f26d9b5.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/24/f_P1240005i_436cm_f26d9b5.jpg)

http://img01.picoodle.com/img/img01/7/1/24/f_P1240006i_436cm_155cded.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/24/f_P1240006i_436cm_155cded.jpg)

http://img02.picoodle.com/img/img02/7/1/24/f_P1240009i_436cm_85a93ff.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/24/f_P1240009i_436cm_85a93ff.jpg)

http://img02.picoodle.com/img/img02/7/1/24/f_P1240010i_436cm_4153cb8.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/24/f_P1240010i_436cm_4153cb8.jpg)

http://img01.picoodle.com/img/img01/7/1/24/f_P1240011i_436cm_47b40f1.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/24/f_P1240011i_436cm_47b40f1.jpg)

Done:
http://img02.picoodle.com/img/img02/7/1/24/f_P1240001i_436cm_dc1e89d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/24/f_P1240001i_436cm_dc1e89d.jpg)

http://img02.picoodle.com/img/img02/7/1/24/f_P1240001i_436cm_264fa0e.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/24/f_P1240001i_436cm_264fa0e.jpg)

Disapointed with an anoying protuberance wich don't let's me close the front panel correctly, so, i did a hole another font, just more longer than first:
http://img02.picoodle.com/img/img02/7/1/24/f_P1240002i_436cm_aeba899.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/24/f_P1240002i_436cm_aeba899.jpg)

Keep the front panel and did all the rest again (waste a lot of expensive plexi)...
http://img01.picoodle.com/img/img01/7/1/24/f_P1240003i_436cm_935764d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/24/f_P1240003i_436cm_935764d.jpg)

And, finelly:
http://img01.picoodle.com/img/img01/7/1/25/f_P1250004i_47bbm_400d660.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/25/f_P1250004i_47bbm_400d660.jpg)

http://img01.picoodle.com/img/img01/7/1/25/f_P1250005i_47bbm_12441b2.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/25/f_P1250005i_47bbm_12441b2.jpg)

http://img01.picoodle.com/img/img01/7/1/25/f_P1250006i_47bbm_b4319dd.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/25/f_P1250006i_47bbm_b4319dd.jpg)

[pedrofilho]

http://img01.picoodle.com/img/img01/7/1/25/f_P1250009i_47bbm_570476b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/25/f_P1250009i_47bbm_570476b.jpg)

Tomorrow i'll post some news about the HDs and WC suport i'll fabricate in 2.4mm cristal plexiglass.

See you !

Pedro Torres.

[pedrofilho]

Because of you, I must now go buy that router attachment.

Hope it do for you the same things it did for me... It's an amazing tool.


i love the power supply pedro +rep wait wat is the non medical use for chlorophrom???

Thank you armadilloben. The nom medical use i think is this i did, using it to work as a soldering glue. What i really don't know is how toxic this thing really is, but, i bought it in a medical center store and had to fill a form with a lot of data about myself to register the buy.

The seller told me to use a mask becouse it's toxic. So i did it. On clorophomio recipient, also, have the information that the substance inside is toxical if in contact with eyes, skin or ingested, smelled, etecetera... So, i really protected myself because of those informations. Used a gas mask, work glasses and gloves.

I used it without any of the protection i told before (except mask and glasses) and have no problems touching it, nothing happens to my skin. But, it was an excepction.

Take care if you intend to use it. Really don't know what exactly is it's toxicity, but, is better it prevented than remedied, don't you think?

Thanks for your observation !


How much money do you have??
every page you buy a new powertool u brazilians most have money trees..

Yeah, and the huge one is rigth on my backyard... lol Or, as Carmen Miranda used to say: Yes we have bananas... :banana:

In fact, i spend a lot of saved money on this project as an anti-stress terapy. As i am saying this days, i am a modder that become an atourney in free time... :D

BTW-> I accept intl donations if you wish... :P

See you !

Pedro Torres.

[pedrofilho]

Nice work and great pics!!! I appreciate all the hard work and attention to detail you are putting into this mod. Thanks for sharing,

Agnat

You're wellcome, Thank you !

Photos of tests i did on new font case:
http://img01.picoodle.com/img/img01/7/1/28/f_P1280001i_16b1m_35b2c16.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/28/f_P1280001i_16b1m_35b2c16.jpg)

Closer:
http://img02.picoodle.com/img/img02/7/1/28/f_P1280002i_16b1m_0301599.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/28/f_P1280002i_16b1m_0301599.jpg)

A small video:
http://www.youtube.com/watch?v=kUZ-9VQcZz0

Slient and beautifull, loved it...
http://img02.picoodle.com/img/img02/7/1/28/f_P1280007i_16b1m_b775f72.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/28/f_P1280007i_16b1m_b775f72.jpg)

What about the font case, what you think? Coments, please! :D
http://img01.picoodle.com/img/img01/7/1/28/f_P1280009i_16b1m_ea135b3.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/28/f_P1280009i_16b1m_ea135b3.jpg)

Some news will arrive tomorrow !

Thank you.

Pedro Torres.

[pedrofilho]

Spent a lot of time today to find all these things:
http://img01.picoodle.com/img/img01/7/1/29/f_P1290001i_b193m_50d0d13.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/29/f_P1290001i_b193m_50d0d13.jpg)

http://img01.picoodle.com/img/img01/7/1/29/f_P1290005i_b193m_b6a727d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/29/f_P1290005i_b193m_b6a727d.jpg)

http://img02.picoodle.com/img/img02/7/1/29/f_P1290006i_b193m_0eeda40.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/29/f_P1290006i_b193m_0eeda40.jpg)

This Dremel bit will do a V cut on acrylic to make easy to blend it.
http://img02.picoodle.com/img/img02/7/1/29/f_P1290008i_b193m_4f2fcb6.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/29/f_P1290008i_b193m_4f2fcb6.jpg)

Maybe, i would bring some news later today...

Pedro Torres.

[pedrofilho]

hey pedro in that pic of the stuff u found i see there is a zieneir diode, some resistors some possibly 100uF capictors but what are those green things on the right??

This is a fantastic eletromagnetic key. I 'till don't know how to put it on schema, but i know it shifts poles (on/off function) when some eletromagnect power pass trought or next to it.

The seller call it of 'red switch' or 'head switch', doesn't understand him after 3 attempts. :D

Tomorrow i'll do a video with an magnet and a multimeter to show it working... Maybe someone can help me doing the power switch i want to, using this thing...

Today i've removed the painting to start exterior works...
http://img02.picoodle.com/img/img02/7/1/30/f_P1300004i_7819m_f60dfd2.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/30/f_P1300004i_7819m_f60dfd2.jpg)

http://img01.picoodle.com/img/img01/7/1/30/f_P1300007i_7819m_8483a52.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/30/f_P1300007i_7819m_8483a52.jpg)

http://img01.picoodle.com/img/img01/7/1/30/f_P1300001i_7819m_0f1fbe6.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/30/f_P1300001i_7819m_0f1fbe6.jpg)

After about 10 minutes the paint was floppy and was easily removed...
http://img01.picoodle.com/img/img01/7/1/30/f_P1300008i_7819m_5424578.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/30/f_P1300008i_7819m_5424578.jpg)

Some water sanding...
http://img02.picoodle.com/img/img02/7/1/30/f_P1300004i_7819m_b485669.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/30/f_P1300004i_7819m_b485669.jpg)

First piece to get sanded
http://img01.picoodle.com/img/img01/7/1/30/f_P1300007i_7819m_772b12b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/30/f_P1300007i_7819m_772b12b.jpg)

Just ready for a cleaner job... :D
http://img02.picoodle.com/img/img02/7/1/30/f_P1300010i_7819m_8552aa3.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/30/f_P1300010i_7819m_8552aa3.jpg)

I'll eat something, blend some plexi and come back here with news, maybe today yet
http://img02.picoodle.com/img/img02/7/1/30/f_P1300001i_7819m_610814b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/30/f_P1300001i_7819m_610814b.jpg)

Thank you !

Pedro Torres.

[pedrofilho]

...That PSU Cover looks amazing.

Great job, and keep it up, once agian.

Glade you like it.

Thank you !

Some material i'll use to mod the CM aquagate-viva. I'll replace the CM black hose for this transparent and add an UV reactive liquid inside the cooler to get some extra lightning effects.

The fluid will travel trought the ET as a flux indicator. The little ET will move when fluid pass trought it's recipient, that will be yet iluminated with leds that oscilate lights witch HDD activity !http://img01.picoodle.com/img/img01/7/1/31/f_P1310007i_61c2m_ca8ba4f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/31/f_P1310007i_61c2m_ca8ba4f.jpg)

Small ET temporary home...
http://img02.picoodle.com/img/img02/7/1/31/f_P1310009i_61c2m_a4ea5d3.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/31/f_P1310009i_61c2m_a4ea5d3.jpg)

These bits are for doing a scretch on plexi to plait it. The first one is for 90 degree or more angle, the second is for 30-45 angles. And third is for borders..
http://img01.picoodle.com/img/img01/7/1/31/f_P1310012i_61c2m_97697a4.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/31/f_P1310012i_61c2m_97697a4.jpg)

http://img01.picoodle.com/img/img01/7/1/31/f_P1310014i_61c2m_65e3052.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/31/f_P1310014i_61c2m_65e3052.jpg)

http://img02.picoodle.com/img/img02/7/1/31/f_P1310018i_61c2m_3a31ddc.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/31/f_P1310018i_61c2m_3a31ddc.jpg)

Plexi bent using the two bits... steps:
http://img01.picoodle.com/img/img01/7/1/31/f_P1310001i_a10dm_233f9a2.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/31/f_P1310001i_a10dm_233f9a2.jpg)

About 45 degree:
http://img02.picoodle.com/img/img02/7/1/31/f_P1310005i_a10dm_7bbe471.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/31/f_P1310005i_a10dm_7bbe471.jpg)

Very inovative and expensive plaiting system... :D (surely it's not)
http://img02.picoodle.com/img/img02/7/1/31/f_P1310006i_a10dm_ceb4ff1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/1/31/f_P1310006i_a10dm_ceb4ff1.jpg)

http://img01.picoodle.com/img/img01/7/1/31/f_P1310010i_a10dm_87cc2a3.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/31/f_P1310010i_a10dm_87cc2a3.jpg)

Details, a clean plait:
http://img01.picoodle.com/img/img01/7/1/31/f_P1310011i_a10dm_ea3ccf9.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/1/31/f_P1310011i_a10dm_ea3ccf9.jpg)

Tomorrow i'll use this tecnique on front panel and, maybe, start the CM cooler mod. Friday will arrive the colldrive 5 and 6 i've bought.

Thank you !

Pedro Torres.

[pedrofilho]

Thanks to folks of www.lasershape.com.br i'll need a fifty bay on case to install a small toy they'll send to me.

Tomorrow i'll put body filler and do some finishing job...

I've started the 5 bay job and did a small plexi window where i intendo do engrave Cooler Master name on front, at side of switches mnptech.com sent to me...
http://img02.picoodle.com/img/img02/7/2/2/f_P2010004i_ba33m_0dd8210.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/2/f_P2010004i_ba33m_0dd8210.jpg)

http://img02.picoodle.com/img/img02/7/2/2/f_P2010007i_ba33m_9bae878.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/2/f_P2010007i_ba33m_9bae878.jpg)

http://img02.picoodle.com/img/img02/7/2/2/f_P2010011i_ba33m_0384078.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/2/f_P2010011i_ba33m_0384078.jpg)

http://img01.picoodle.com/img/img01/7/2/2/f_P2020002i_ba33m_8c1e1d8.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/2/f_P2020002i_ba33m_8c1e1d8.jpg)

Every day i love it more, holy Dremel saw, it's really amazing with plexi, lets dust all together, ease to clean (love it)http://img02.picoodle.com/img/img02/7/2/2/f_P2020004i_ba33m_a9600bf.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/2/f_P2020004i_ba33m_a9600bf.jpg)

A clean and precise cut:
http://img01.picoodle.com/img/img01/7/2/2/f_P2020005i_ba33m_b931b30.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/2/f_P2020005i_ba33m_b931b30.jpg)

Borderes of plexi piece wictch will abrigate de swtiches mnptech.com sent to me and CM logo...
http://img01.picoodle.com/img/img01/7/2/2/f_P2020008i_ba33m_18fe628.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/2/f_P2020008i_ba33m_18fe628.jpg)

Fits perfectly, at first attempt
http://img02.picoodle.com/img/img02/7/2/2/f_P2020009i_ba33m_57e452a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/2/f_P2020009i_ba33m_57e452a.jpg)

Arrived the UV cooler to Aguagate Viva i'll mod, replacing black hoses for transparente and for the ET reservoir i won from www.neptuno.com.br, nice...
http://img01.picoodle.com/img/img01/7/2/2/f_P2020003i_ba33m_b282be1.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/2/f_P2020003i_ba33m_b282be1.jpg)

Keep going...
http://img01.picoodle.com/img/img01/7/2/2/f_P2020001i_ba33m_0d0bb33.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/2/f_P2020001i_ba33m_0d0bb33.jpg)

de_dust2
http://img01.picoodle.com/img/img01/7/2/2/f_P2020002i_ba33m_2565102.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/2/f_P2020002i_ba33m_2565102.jpg)

http://img02.picoodle.com/img/img02/7/2/2/f_P2020009i_ba33m_3c43977.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/2/f_P2020009i_ba33m_3c43977.jpg)

Piece as i left it some time ago, now it's fixed with epoxi and washed, tomorrow i'll do a finish job and sand it. Also will do a plexi panel and prepare to receive new ET reservoir... Maybe start CM WC mod also.http://img01.picoodle.com/img/img01/7/2/2/f_P2020011i_ba33m_f20e384.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/2/f_P2020011i_ba33m_f20e384.jpg)

This today job seems easy, but, give-me a lot of work on detais of this piece. It's importanto to the project, because will carry on a lot of beautifull things, including the CM aquagate-viva reservoir ET, fans and a lot of lights.

See you soon with nice mods...

Thank you !

Pedro Torres.

[pedrofilho]

man, you shure got stady hands, those are some of the cleanest cuts i ever seen

Really got a nice cut this time...

Apreciate your coment, Thank you !

Fall from bed today and started working on front panel. After dry i'll sand it, cut the roof and put some plexi. Also, i'll do the front panel plexi window.

Photos:
http://img01.picoodle.com/img/img01/7/2/3/f_P2030001i_d572m_7f5ac17.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/3/f_P2030001i_d572m_7f5ac17.jpg)

http://img01.picoodle.com/img/img01/7/2/3/f_P2030002i_d572m_e78b083.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/3/f_P2030002i_d572m_e78b083.jpg)

It's almost ready to sanding...

See you soon !

Pedro Torres.

[pedrofilho]

The project is going faster now. This week i'll finish the front panel and do some paint and mounting works.

Today most updates:

To fill...
http://img02.picoodle.com/img/img02/7/2/3/f_P2030004i_539am_5d1d6fb.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/3/f_P2030004i_539am_5d1d6fb.jpg)

To cut...
http://img01.picoodle.com/img/img01/7/2/3/f_P2030005i_539am_c0da55b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/3/f_P2030005i_539am_c0da55b.jpg)

To measurements and suport...
http://img01.picoodle.com/img/img01/7/2/3/f_P2030009i_539am_6e43fd9.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/3/f_P2030009i_539am_6e43fd9.jpg)

Plexi to front panel
http://img01.picoodle.com/img/img01/7/2/3/f_P2030013i_539am_0e7740b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/3/f_P2030013i_539am_0e7740b.jpg)

Piece cuted and marked
http://img02.picoodle.com/img/img02/7/2/3/f_P2030016i_539am_9013a14.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/3/f_P2030016i_539am_9013a14.jpg)

Frontal panel works:
http://img01.picoodle.com/img/img01/7/2/3/f_P2030006i_539am_d8e15be.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/3/f_P2030006i_539am_d8e15be.jpg)

Screcth on V to makes easly de folding it...
http://img01.picoodle.com/img/img01/7/2/3/f_P2030007i_539am_192fd5f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/3/f_P2030007i_539am_192fd5f.jpg)

To cut the groove
http://img02.picoodle.com/img/img02/7/2/3/f_P2030011i_539am_ff1a07e.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/3/f_P2030011i_539am_ff1a07e.jpg)

The roof will act with front panel, so i've to cut and do a small test. rs. before cutting the front panel...
http://img01.picoodle.com/img/img01/7/2/3/f_P2030013i_539am_ad8d360.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/3/f_P2030013i_539am_ad8d360.jpg)

After this cut i tested the idea and works, so, keep cuting the front panel...
http://img02.picoodle.com/img/img02/7/2/3/f_P2030017i_539am_7a72d9f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/3/f_P2030017i_539am_7a72d9f.jpg)

It's expensive, must use all that...
http://img02.picoodle.com/img/img02/7/2/3/f_P2030002i_539am_d65d151.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/3/f_P2030002i_539am_d65d151.jpg)

Groove cuted, it works..
http://img02.picoodle.com/img/img02/7/2/3/f_P2030008i_539am_d4f998d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/3/f_P2030008i_539am_d4f998d.jpg)

Tomorrow i'll do a finishing job on this, fits perfectly, loved it...
http://img01.picoodle.com/img/img01/7/2/3/f_P2030014i_539am_3d23224.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/3/f_P2030014i_539am_3d23224.jpg)

Tomorrow i'll finish this and do other things.
http://img01.picoodle.com/img/img01/7/2/3/f_P2030015i_539am_22d7931.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/3/f_P2030015i_539am_22d7931.jpg)

I am really tired, have not to say, started to soon today and don't stop until now.

See you tomorrow, i'm exausted... Today was a great day, did a lot of advances, tomorrow i'll do more... Hope !

Thank you,

Pedro Torres.

[pedrofilho]

great work pedro, I realy like what you are doing with the front panel

I brought some news about that, right now...

Thanks


Nice man i Really like it. I spent about 20 minutes reading the whole thread lol.

It's really have a lot of posts already... Nice reading.

Be wellcome !

Firsts results with front panel:
http://img01.picoodle.com/img/img01/7/2/4/f_P2040001i_852cm_62c3f7b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/4/f_P2040001i_852cm_62c3f7b.jpg)

Have a Dremel nylon disk that may work to do a polishing job on corners, to get a better tranparency...
http://img02.picoodle.com/img/img02/7/2/4/f_P2040003i_852cm_496c6a7.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/4/f_P2040003i_852cm_496c6a7.jpg)

Will close up and down with plexi and put a hinge pair in left side:
http://img01.picoodle.com/img/img01/7/2/4/f_P2040005i_852cm_4ecada3.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/4/f_P2040005i_852cm_4ecada3.jpg)

See you later !

Pedro Torres.

[pedrofilho]

very nice update pedro, i rely love this work log!

+REP

Thank you GT40_GearHead,

Today i did some modifications on original idea to front panel, because i do not like the visual that came out before. So, i did it another time, and, now it pop up as i expected... Liked it !

Thanks for beeing here, you're wellcome !


You are doing some awesome work Pedro, keep it up dude!

Thank you jbdnsn, be sure i am trying to do always the best i can, to share with friends like you.

Thanks.

Now the news...

I did another front panel to show better the hot stuff i'll put on 5 1/4 bays. Two of then are CM stuff, a cooldrive 6 and a cooldrive 5, and a vantec nexus to cpu, with usb e firewire conectors... Beautifull... Also, it will show the 3 vandal switch when i install it...

Let's go to photos..
http://img02.picoodle.com/img/img02/7/2/5/f_P2050002i_1a85m_75206bd.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/5/f_P2050002i_1a85m_75206bd.jpg)

http://img01.picoodle.com/img/img01/7/2/5/f_P2050003i_1a85m_3e6ccb9.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/5/f_P2050003i_1a85m_3e6ccb9.jpg)

The metod
http://img01.picoodle.com/img/img01/7/2/5/f_P2050005i_1a85m_0038998.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/5/f_P2050005i_1a85m_0038998.jpg)

Have to use gloves, so you don't get burned... ouch ! :D
http://img02.picoodle.com/img/img02/7/2/5/f_P2050007i_1a85m_82f7fcd.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/5/f_P2050007i_1a85m_82f7fcd.jpg)

http://img02.picoodle.com/img/img02/7/2/5/f_P2050009i_1a85m_d546f51.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/5/f_P2050009i_1a85m_d546f51.jpg)

http://img02.picoodle.com/img/img02/7/2/5/f_P2050011i_1a85m_d3a3dbc.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/5/f_P2050011i_1a85m_d3a3dbc.jpg)

Anoying white stuff...
http://img01.picoodle.com/img/img01/7/2/5/f_P2050012i_1a85m_033629f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/5/f_P2050012i_1a85m_033629f.jpg)

Now what?! I really like as this come out this time ! Clean and precise. Tomorrow i'll do a finishing job...
http://img02.picoodle.com/img/img02/7/2/5/f_P2050015i_1a85m_b8db267.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/5/f_P2050015i_1a85m_b8db267.jpg)

I'll do all i can to mount the case until 17.02.2007 because there is another contest i want to participate. And until the end of the year it will got some improvements to CM 2007 WW contest, the final goal of this Expensive, hardwork and delicious project...

See you tomorrow with more pretty news, until thursday some pieces will arrive here... Nice stuff... :)

Pedro Torres.

[pedrofilho]

Today i got my Dremel D-Vise from the customs. They stay with it since december and set it free just yesterday... I really miss this tool, but, now i got it !
http://img02.picoodle.com/img/img02/7/2/6/f_P2060002m_f04e426.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/6/f_P2060002m_f04e426.jpg)

http://img01.picoodle.com/img/img01/7/2/6/f_P2060003m_78ce4df.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/6/f_P2060003m_78ce4df.jpg)

http://img02.picoodle.com/img/img02/7/2/6/f_P2060004m_e2e0d02.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/6/f_P2060004m_e2e0d02.jpg)

http://img02.picoodle.com/img/img02/7/2/6/f_P2060005m_b7b4c8d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/6/f_P2060005m_b7b4c8d.jpg)

http://img01.picoodle.com/img/img01/7/2/6/f_P2060006m_d0243f6.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/6/f_P2060006m_d0243f6.jpg)

http://img01.picoodle.com/img/img01/7/2/6/f_P2060009m_a9a681a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/6/f_P2060009m_a9a681a.jpg)

See you later with today's mods.

Thank you !

Pedro Torres.

[pedrofilho]

Looking great Pedro. Really can't wait to see this mod running. Crackin!! :banana:

Soon as february 17. this day is the last day to subscrive on a Dremel contest here... After that i'll do some finishings, until the CM WW contest on the end of the year ;)

Thank you !


Wow. Can't wait to see the end result!

It's near, hold on... I want it mounted february 17 and tomorrow i'll do a hard sanding job to paint all internal pieces until the weekend when i'll start some exterior textures.

Thank you !

Some work i did today is preparation to others.

This is how i intend to mount the Alien vs. Predator playset, over a iluminated black plaxi plate engraved... (wow)
http://img01.picoodle.com/img/img01/7/2/6/f_P2060001m_391e5d1.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/6/f_P2060001m_391e5d1.jpg)

This is the cut i'll use as the playset base:
http://img01.picoodle.com/img/img01/7/2/6/f_P2060004m_a6c1f96.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/6/f_P2060004m_a6c1f96.jpg)

As i intent to engrave over black paint, i did it today, to do the engraving job on next week, when the paint will be totaly dry to suport the work with minimal secondary damages.
http://img02.picoodle.com/img/img02/7/2/6/f_P2060007m_9df318a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/6/f_P2060007m_9df318a.jpg)

Well, tomorrow i'll sand some pieces, so, i prepared some parts to do an one time job...
http://img02.picoodle.com/img/img02/7/2/6/f_P2060009m_162ddf6.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/6/f_P2060009m_162ddf6.jpg)

See you folks.

Pedro Torres.

[pedrofilho]

Do not resist, this is the way it will be on case. With a small elevation. The paint job pop up explendid. I'll wait it dry completly next week to do the engraving work.

http://img01.picoodle.com/img/img01/7/2/6/f_P2060004m_a0f7b27.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/6/f_P2060004m_a0f7b27.jpg)

See you tomorrow,

Pedro Torres.

BTW-> I'll apreciate sugestions about the figure i must engrave on this alien vs. predator base. Anything like an alien texture or hierogliplhos, things like that... Thanks.

[pedrofilho]

Just started the sanding job and those toys arrived to stop the works...
http://img01.picoodle.com/img/img01/7/2/7/f_P2070003m_e6ff6e4.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/7/f_P2070003m_e6ff6e4.jpg)

http://img02.picoodle.com/img/img02/7/2/7/f_P2070004m_58c44ce.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070004m_58c44ce.jpg)

http://img01.picoodle.com/img/img01/7/2/7/f_P2070005m_784416a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/7/f_P2070005m_784416a.jpg)

Later i'll put some photos e also when mount then.
http://img02.picoodle.com/img/img02/7/2/7/f_P2070006m_7554263.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070006m_7554263.jpg)

http://img01.picoodle.com/img/img01/7/2/7/f_P2070010m_0a9935a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/7/f_P2070010m_0a9935a.jpg)

http://img02.picoodle.com/img/img02/7/2/7/f_P2070007m_823aa01.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070007m_823aa01.jpg)

http://img02.picoodle.com/img/img02/7/2/7/f_P2070012m_ddf110e.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070012m_ddf110e.jpg)

This Cooldrive 5 is a beautifull dream... Amazing...
http://img01.picoodle.com/img/img01/7/2/7/f_P2070009m_16bbec3.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/7/f_P2070009m_16bbec3.jpg)

http://img02.picoodle.com/img/img02/7/2/7/f_P2070011m_fc6348b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070011m_fc6348b.jpg)

This items are the reason to transparent front panel, i could't hide this things, they're really nice.

See you later,

Pedro Torres.

[pedrofilho]

Noice.
/subscribed
+rep

Thank you for your support.

As i promess, more work and a lot of photos:

Side windows ready for texturing:
http://img01.picoodle.com/img/img01/7/2/7/f_P2070001m_8dc9da2.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/7/f_P2070001m_8dc9da2.jpg)

Powerfull 10mm UV Leds to case feet:
http://img02.picoodle.com/img/img02/7/2/7/f_P2070006m_f3af34f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070006m_f3af34f.jpg)

I'll sand more tomorrow, the base is not good:
http://img02.picoodle.com/img/img02/7/2/7/f_P2070007m_5e32d4d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070007m_5e32d4d.jpg)

Have to do some finishing works with Dremel before sanding...
http://img02.picoodle.com/img/img02/7/2/7/f_P2070010m_1c95b53.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070010m_1c95b53.jpg)

Front panel is ready for paint:
http://img02.picoodle.com/img/img02/7/2/7/f_P2070011m_7231d5b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070011m_7231d5b.jpg)

Toys:
http://img02.picoodle.com/img/img02/7/2/7/f_P2070012m_24aa990.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070012m_24aa990.jpg)

http://img02.picoodle.com/img/img02/7/2/7/f_P2070015m_c70ee29.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070015m_c70ee29.jpg)

http://img02.picoodle.com/img/img02/7/2/7/f_P2070016m_b678d8b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070016m_b678d8b.jpg)

http://img02.picoodle.com/img/img02/7/2/7/f_P2070008m_3cd32a3.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070008m_3cd32a3.jpg)

http://img02.picoodle.com/img/img02/7/2/7/f_P2070009m_bf49fe6.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070009m_bf49fe6.jpg)

http://img01.picoodle.com/img/img01/7/2/7/f_P2070017m_330064c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/7/f_P2070017m_330064c.jpg)

http://img01.picoodle.com/img/img01/7/2/7/f_P2070011m_29b95bc.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/7/f_P2070011m_29b95bc.jpg)

http://img02.picoodle.com/img/img02/7/2/7/f_P2070013m_2771461.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070013m_2771461.jpg)

http://img02.picoodle.com/img/img02/7/2/7/f_P2070015m_42dfe25.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070015m_42dfe25.jpg)

http://img02.picoodle.com/img/img02/7/2/7/f_P2070017m_d60cd74.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070017m_d60cd74.jpg)

http://img02.picoodle.com/img/img02/7/2/7/f_P2070018m_db94554.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070018m_db94554.jpg)

http://img01.picoodle.com/img/img01/7/2/7/f_P2070002Bm_ddd0de9.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/7/f_P2070002Bm_ddd0de9.jpg)

http://img01.picoodle.com/img/img01/7/2/7/f_P2070001m_12fdd85.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/7/f_P2070001m_12fdd85.jpg)

A lot of acessories and extras
http://img02.picoodle.com/img/img02/7/2/7/f_P2070011m_6c29b6a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/7/f_P2070011m_6c29b6a.jpg)

Really nice extra fronts i won as gift from a brazilian casemod store!
http://img01.picoodle.com/img/img01/7/2/7/f_P2070004m_6599657.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/7/f_P2070004m_6599657.jpg)

The photos do not reveal all the colors and bright of these items, they're really beautifull stuff ! Hope get better photos when mount the case at daylight !

Thank You !

Pedro Torres.

[pedrofilho]

pedro if ure looking for 470ohm resistors i just bought about 1k of em from best hong kong ill be more then willing to ship em to ya if u pay for shipping
btw what are the specs on the 10mm's u got i got 10 prewired 12v uv leds as well except they dont excite the uv paint:down:

overall this thing is comin out wonderfully gj man


-ben

Ben,

I really apreciate your offer, but, i've already bought all resistors i'll need to leds.

Thank you very much !

Most of today's work was sanding and polishing job...

http://img01.picoodle.com/img/img01/7/2/8/f_P2080001m_54fe1e0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/8/f_P2080001m_54fe1e0.jpg)

http://img02.picoodle.com/img/img02/7/2/8/f_P2080002m_e4a6ca1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/8/f_P2080002m_e4a6ca1.jpg)

http://img02.picoodle.com/img/img02/7/2/8/f_P2080003m_b477877.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/8/f_P2080003m_b477877.jpg)

http://img02.picoodle.com/img/img02/7/2/8/f_P2080004m_663baa8.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/8/f_P2080004m_663baa8.jpg)

http://img01.picoodle.com/img/img01/7/2/8/f_P2080005m_ce3830c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/8/f_P2080005m_ce3830c.jpg)

Paint to see all defective points
http://img02.picoodle.com/img/img02/7/2/8/f_P2080006m_9b9f44a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/8/f_P2080006m_9b9f44a.jpg)

http://img01.picoodle.com/img/img01/7/2/8/f_P2080007m_885d1d1.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/8/f_P2080007m_885d1d1.jpg)

And i locate a lot of them
http://img02.picoodle.com/img/img02/7/2/8/f_P2080008m_3778e07.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/8/f_P2080008m_3778e07.jpg)

Got a hard work today and tomorrow i'll do a paint job on this case !

Thank you !

Pedro Torres.

[pedrofilho]

Fall from bed...

Could't resist to bring the news about front panel paintings....

It's pop up fantastic, trully amazing... Now i fully believe on spray paints, whata !

Those fotos i've got last night and still are not good enough. When sun come out i'll take better shots...

http://img02.picoodle.com/img/img02/7/2/9/f_P2080006m_45c57ed.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/9/f_P2080006m_45c57ed.jpg)

http://img02.picoodle.com/img/img02/7/2/9/f_P2080008m_31febc6.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/9/f_P2080008m_31febc6.jpg)

Now i'm going to do a paint job on that case. Whe stores open around here, i'll buy more sands...

See you later with big huge news...

Pedro Torres.

[pedrofilho]

Your attention to detail Pedro is fantastic. Thank you for showing us what you are doing and the great pics. Keep up the good work!

Agnat

Your's friednship is what really matter here. I'll do everything i can to do my best.

Again, thank you Agnat !


Excellent work as always Pedro. I always look forward to your updates. By the way, where did you find those HUGE LED's? They look like you could use them on your car.

Hello sgtm,

I bought it at brasilian e-Bay affiliated called mercadolivre.com. They are 10mm Leds and really brights the way. Today, at night, i'll post some photos of one of this leds conected on a 12V power source with a 370ohms resistor, since the leds are 3.5~3.8V

Thank you for your visit !

Bring some photos of front panel painting first results (at daylight):
http://img02.picoodle.com/img/img02/7/2/9/f_P2090004m_37abde4.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/9/f_P2090004m_37abde4.jpg)

http://img01.picoodle.com/img/img01/7/2/9/f_P2090007m_5046d62.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/9/f_P2090007m_5046d62.jpg)

Upside down...
http://img02.picoodle.com/img/img02/7/2/9/f_P2090009m_9c11295.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/9/f_P2090009m_9c11295.jpg)

On case:
http://img01.picoodle.com/img/img01/7/2/9/f_P2090001m_7a29d3c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/9/f_P2090001m_7a29d3c.jpg)

More water sands, i think it's enought now !
http://img01.picoodle.com/img/img01/7/2/9/f_P2090011m_c67e796.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/9/f_P2090011m_c67e796.jpg)

I'll try to fabricate this thing on plexi, if unsucessfull i'll use it directly and mount it onto the front panel left side:
http://img02.picoodle.com/img/img02/7/2/9/f_P2090012m_a839c78.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/9/f_P2090012m_a839c78.jpg)

Later i'll post some photos of 10mm leds on action and finish the sand job, now, i'm going to a law meeting... As atourney sure... :d

Thank you for your visit !

Pedro Torres.

[pedrofilho]

Folks, look what i got with those huge leds, they're really show stunting lights !

Impressive, now i decide replace all 5mm leds for those 10mm. It is trully amazing, whatch this:
http://img02.picoodle.com/img/img02/7/2/9/f_P2090003m_7a6b4cd.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/9/f_P2090003m_7a6b4cd.jpg)

http://img02.picoodle.com/img/img02/7/2/9/f_P2090005m_2e19ea3.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/9/f_P2090005m_2e19ea3.jpg)

They have a very long range and a great ilumination capacity:
http://img01.picoodle.com/img/img01/7/2/9/f_P2090002m_8dddc7f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/9/f_P2090002m_8dddc7f.jpg)

I beeing imagining this thing with some lens and other direcional gears. It pumps light everywhere, front, sides and back... I am impressed !
http://img02.picoodle.com/img/img02/7/2/9/f_P2090012m_205997d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/9/f_P2090012m_205997d.jpg)

See you tomorrow fellows, a law meeting today take all my day and i couldn't work more on case, tomorrow i'll do that case paint ! I promiss that ! You have my word i'll paint the case !

Pedro Torres.

[pedrofilho]

Damn! Those things are bright!!!

A true inspiration...now if only the weather would cooperate I'd start cracking on the mod I'm gonna do for my parents.

If I could give ya more rep, I would. You've sure earned it!

Is the snow storm that you are talking about? Is cold there? Come to Brazil ! Here is summer and next week is carnaval on Rio, Recife, Olinda e Salvador ! Hot stuff ! :P

Thank you for visiting me !


**** pedro those lights are really bright my 10mm blues and the 5mm piranhas are about the same brightness keep up the sick work my friend:up:

Hi Ben, It's really bright and range of light is really amazing...

Thank you !

Worked hard today on paint preparation and found some mistakes on preparation steps and had to do some extra sanding job... Let the case sanded, mounted and washed, so, tomorrow is just paint it all.

Got an exceptional news today, the small ET reservoir is done and tuersday it'll arrive here.

The pretty stuff from sponsor neptuno.com.br:
http://img01.picoodle.com/img/img01/7/2/10/f_S2020336m_9be6751.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/10/f_S2020336m_9be6751.jpg)

http://img02.picoodle.com/img/img02/7/2/10/f_S2020337m_218d074.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/10/f_S2020337m_218d074.jpg)

http://img01.picoodle.com/img/img01/7/2/10/f_P2100001m_e6d76ae.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/10/f_P2100001m_e6d76ae.jpg)

http://img02.picoodle.com/img/img02/7/2/10/f_P2100011m_20c5a3e.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/10/f_P2100011m_20c5a3e.jpg)

http://img01.picoodle.com/img/img01/7/2/10/f_P2100013m_f4bdb3d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/10/f_P2100013m_f4bdb3d.jpg)

http://img01.picoodle.com/img/img01/7/2/10/f_P2100015m_d758ee8.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/10/f_P2100015m_d758ee8.jpg)

http://img01.picoodle.com/img/img01/7/2/10/f_P2100016m_b9bde5b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/10/f_P2100016m_b9bde5b.jpg)

http://img02.picoodle.com/img/img02/7/2/10/f_P2100001m_5fddcd2.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/10/f_P2100001m_5fddcd2.jpg)

http://img01.picoodle.com/img/img01/7/2/10/f_P2100002m_7317158.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/10/f_P2100002m_7317158.jpg)

http://img02.picoodle.com/img/img02/7/2/10/f_P2100004m_bc86704.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/10/f_P2100004m_bc86704.jpg)

http://img01.picoodle.com/img/img01/7/2/10/f_P2100010m_d0dcf00.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/10/f_P2100010m_d0dcf00.jpg)

http://img01.picoodle.com/img/img01/7/2/10/f_P2100014m_c6feffd.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/10/f_P2100014m_c6feffd.jpg)

http://img01.picoodle.com/img/img01/7/2/10/f_P2100015m_825a1da.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/10/f_P2100015m_825a1da.jpg)

http://img01.picoodle.com/img/img01/7/2/10/f_P2100016m_371d22d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/10/f_P2100016m_371d22d.jpg)

http://img02.picoodle.com/img/img02/7/2/10/f_P2100017m_8dc3dd8.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/10/f_P2100017m_8dc3dd8.jpg)

I am done for today, tomorrow i've a paint to do !

Hold on,

Pedro Torres.

[pedrofilho]

I've liked your mod so much, that I featured you and your Brazilian neighbor on the front page. Great work Pedro!
http://www.thebestcasescenario.com

Thank you jdbnsn, you makes me really proud. TBCS is one of the place that keeps the most impressive cases i ever seen and to figure out on front page is a big honour to me.

Again,

Thank you very much !


Excellent work Pedro. Congrats on the front page spot! +rep

Thank you sgtm, it lets me very happy and proud !

I apreciate your constant support and coments you always lets here.

Nice to see you !


Yeah, we are getting some snow in Montana, but nothing like New York!

Winters here can be rough at times, but the last few have been tolerable.

Grade A work all the way, keep up the good work! +Rep!

Dude, look the sun of those photos below and you'll see what you are missing here... :D

To makes thinks still more attractive is carnaval time in Brazil.

Thanks for your suport, as it is here, i hope the weather gets better on you beautiful country too...

And, as i promised, the paint job:
http://img01.picoodle.com/img/img01/7/2/11/f_P2110001m_c42332f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/11/f_P2110001m_c42332f.jpg)

http://img02.picoodle.com/img/img02/7/2/11/f_P2110002m_88396b6.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/11/f_P2110002m_88396b6.jpg)

http://img02.picoodle.com/img/img02/7/2/11/f_P2110003m_aac5084.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/11/f_P2110003m_aac5084.jpg)

http://img02.picoodle.com/img/img02/7/2/11/f_P2110006m_56c26f3.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/11/f_P2110006m_56c26f3.jpg)

http://img01.picoodle.com/img/img01/7/2/11/f_P2110008m_d9a516c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/11/f_P2110008m_d9a516c.jpg)

http://img02.picoodle.com/img/img02/7/2/11/f_P2110009m_59dad26.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/11/f_P2110009m_59dad26.jpg)

http://img01.picoodle.com/img/img01/7/2/11/f_P2110010m_617adfb.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/11/f_P2110010m_617adfb.jpg)

http://img02.picoodle.com/img/img02/7/2/11/f_P2110011m_15a804c.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/11/f_P2110011m_15a804c.jpg)

http://img01.picoodle.com/img/img01/7/2/11/f_P2110013m_8c3d737.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/11/f_P2110013m_8c3d737.jpg)

http://img02.picoodle.com/img/img02/7/2/11/f_P2110012m_f8f6eef.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/11/f_P2110012m_f8f6eef.jpg)

http://img02.picoodle.com/img/img02/7/2/11/f_P2110004m_25c820b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/11/f_P2110004m_25c820b.jpg)

http://img01.picoodle.com/img/img01/7/2/11/f_P2110006m_2e02f07.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/11/f_P2110006m_2e02f07.jpg)

http://img02.picoodle.com/img/img02/7/2/11/f_P2110009m_914ffc9.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/11/f_P2110009m_914ffc9.jpg)

http://img02.picoodle.com/img/img02/7/2/11/f_P2110010m_e1a0ca6.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/11/f_P2110010m_e1a0ca6.jpg)

I'll need two half screws and the Dremel vise started to work, very nice:
http://img02.picoodle.com/img/img02/7/2/11/f_P2110003m_6342641.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/11/f_P2110003m_6342641.jpg)

http://img02.picoodle.com/img/img02/7/2/11/f_P2110006m_e5c73b8.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/11/f_P2110006m_e5c73b8.jpg)

http://img02.picoodle.com/img/img02/7/2/11/f_P2110008m_4bf1ce0.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/11/f_P2110008m_4bf1ce0.jpg)

http://img01.picoodle.com/img/img01/7/2/11/f_P2110011m_9aa4dc9.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/11/f_P2110011m_9aa4dc9.jpg)

See you soon with more news...

Pedro Torres

[pedrofilho]

Excellent work my friend. I would have never thought of hanging the case with string--damn now I see even more fabrication work in my immediate future!

This thread delivers!

+rep

It's nice with strings because you can put the case on the height you want to work and becomes very confortable the painting job.

Let me know when you start your case, i'll like to see it.

Thanks for visiting,

Pedro Torres.

[pedrofilho]

I'm shooting for starting in mid March--getting all my supplies together right now.

It is a good idea to do a scketh of your project and organize supplies to the job. Do not forget to buy tape of many kinds, you'll need it ! ;)

See you !

Well, i do not resist and did a small test with some light to see if the paint really works and, look at that thing:
http://img02.picoodle.com/img/img02/7/2/11/f_P2110003m_e40c51f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/11/f_P2110003m_e40c51f.jpg)

http://img01.picoodle.com/img/img01/7/2/11/f_P2110009m_39d9cb4.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/11/f_P2110009m_39d9cb4.jpg)

http://img02.picoodle.com/img/img02/7/2/11/f_P2110010m_17a5328.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/11/f_P2110010m_17a5328.jpg)

http://img02.picoodle.com/img/img02/7/2/11/f_P2110011m_ebd33aa.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/11/f_P2110011m_ebd33aa.jpg)

http://img01.picoodle.com/img/img01/7/2/11/f_P2110013m_846e1e7.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/11/f_P2110013m_846e1e7.jpg)

I am really impressed, it pumps lights everywhere and it's just 2 CC and i'll use 4 UV CC...

See you soon with more nice updates,

Pedro Torres.

[pedrofilho]

Great colors!

I love colors, and i'll use a lot. On second chapter of this mod í'll do some changes on colores. I just have to mount it on friday to a contest subscription, but, i'll do a larger finishing job on it.

But, you're right. The colors are stunt yeah !

Thank You jdbnsn !


I look from my desolate wasteland in Wisconsin (where the temps are still near zero F) to your lush jungle backdrop, and i think. How big are the mosquitoes? They die every year up here, but Manny, Manny. they could probably eat a cat down by you.

This mod is frickin' ridiculous!
i wan't to but i cant even give you +rep anymore.
Just consider it a Preemptive +rep

They are not bigger than me and my skin is covered by paint, plexi, and other chemical they do not like... :p

Thank you for your support, you're wellcome always..



Maz, I feel your pain. -6 F here right now, and the wind is blowing something fierce (which isn't anything new). Dunno about your neck of the woods, but we're supposed to be around 40 above by the weekend.

And I also agree with you 100% on this mod. Very inspiring!

Thanks again drumthumper, i hope the weather gets better, until there, stay in home and drink some hot chocolate.

Peace, see you...

Folks,

Try watching this case tomorrow, i'll post the bigger update before the first chapter ends friday. Yeah, that's right, will be a second chapter on this. I already order a lot of news to do other larger update on this case. I really want to do the best case i can to participate on 2007 CM WW contest at the end of the year.

The second part starts 18.02.2007 and consists on repaint the case, add some news and do a professional job on font, includind removing this temporary paint and, also, doing a lot of finishings works.

Tomorrow i'll post the biggest update since the beggining of this project, before the D day.

First the photos...

http://img01.picoodle.com/img/img01/7/2/13/f_P2130001m_f76ccdc.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/13/f_P2130001m_f76ccdc.jpg)

http://img01.picoodle.com/img/img01/7/2/13/f_P2130002m_21185af.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/13/f_P2130002m_21185af.jpg)

http://img01.picoodle.com/img/img01/7/2/13/f_P2130006m_27e0045.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/13/f_P2130006m_27e0045.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130008m_cb90973.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130008m_cb90973.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130009m_02affbc.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130009m_02affbc.jpg)

http://img01.picoodle.com/img/img01/7/2/13/f_P2130010m_a84f72f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/13/f_P2130010m_a84f72f.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130012m_abe003f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130012m_abe003f.jpg)

http://img01.picoodle.com/img/img01/7/2/13/f_P2130001m_f184207.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/13/f_P2130001m_f184207.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130005m_57e5210.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130005m_57e5210.jpg)

http://img01.picoodle.com/img/img01/7/2/13/f_P2130006m_3a7abfd.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/13/f_P2130006m_3a7abfd.jpg)

http://img01.picoodle.com/img/img01/7/2/13/f_P2130014m_2499ef3.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/13/f_P2130014m_2499ef3.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130001m_953e87a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130001m_953e87a.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130003m_2d2d134.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130003m_2d2d134.jpg)

http://img01.picoodle.com/img/img01/7/2/13/f_P2130005m_9aa44ab.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/13/f_P2130005m_9aa44ab.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130007m_d675b56.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130007m_d675b56.jpg)

http://img01.picoodle.com/img/img01/7/2/13/f_P2130012m_cf71d13.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/13/f_P2130012m_cf71d13.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130014m_3cf5140.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130014m_3cf5140.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130016m_bdbfafd.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130016m_bdbfafd.jpg)

http://img01.picoodle.com/img/img01/7/2/13/f_P2130017m_49de774.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/13/f_P2130017m_49de774.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130018m_2f3f50c.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130018m_2f3f50c.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130002m_c7adbf5.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130002m_c7adbf5.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130003m_32d4c35.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130003m_32d4c35.jpg)

http://img01.picoodle.com/img/img01/7/2/13/f_P2130004m_ffa8fe8.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/13/f_P2130004m_ffa8fe8.jpg)

http://img01.picoodle.com/img/img01/7/2/13/f_P2130005m_12e8c32.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/13/f_P2130005m_12e8c32.jpg)

[pedrofilho]

http://img02.picoodle.com/img/img02/7/2/13/f_P2130008m_f44170d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130008m_f44170d.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130009m_2b05bc1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130009m_2b05bc1.jpg)

http://img01.picoodle.com/img/img01/7/2/13/f_P2130011m_b5fdb00.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/13/f_P2130011m_b5fdb00.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130012m_3305abe.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130012m_3305abe.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130001m_c771b1e.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130001m_c771b1e.jpg)

http://img01.picoodle.com/img/img01/7/2/13/f_P2130002m_8b49a2f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/13/f_P2130002m_8b49a2f.jpg)

http://img02.picoodle.com/img/img02/7/2/13/f_P2130009m_a52a26f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/13/f_P2130009m_a52a26f.jpg)

1. The case will be mounted friday.

2. This will be the end of first chapter, because, i've decided to do another part giving this case a professional look and finishing job.

3. I won a really nice sponsor reservoir from neptuno.com.br and other from an american strore that will figurate on this case on chapter two.

4. Today i've some problems with reservoir conector and tomorrow i'll do the WC aquagate-viva mod and mount the ET on it's new home.

5. I've soft sanded the case to apply another paint coat and will polish it to give an extra bright tomorrow too.

6. Put the holder on top panel and tomorrow i'll do an texture painting, fix it and iluinate the Et over the case.

7. I'll do a temporary switch while those bulgin ones do not arrives here...

8. The font wins a analog termometer display i''ll put it on and remove the paint i did on font in the second chapter of this mod.

9. Also, all the case will get a professional cable sleeving, including font and all his conectors.

9. Did some screws and other works preparing for tomorrow jobs...

10. I'll work on lights when go mount the case friday.

11. I'll redo the 3D plexi ET face on transparent plexi to do not interfere on inside colors i got to case. It's really nice.

I have a lawer work tomorrow but i'll finish it at noon,

See you tomorrow witch the bigger update since begining...

Pedro Torres.

[pedrofilho]

Folks,

I am incredible tired and did an video of the first time i turned on the pc after first part of mod.

That's it for now, tomorrow i'll do another post with all photos and coment all of your posts.

Now i'm going to bed, so tired...

Enjoy,

Pedro Torres.

PS-> http://www.youtube.com/watch?v=UKTqlqdtuRY
UKTqlqdtuRY

[pedrofilho]

This post is the final of first part of the mod. Second part is already started and soon as i get some stuff i've ordered i'll bring the news...

First a lot of photos and two videos, after that, the coments...

http://www.youtube.com/watch?v=UKTqlqdtuRY
http://www.youtube.com/watch?v=aIe4SUu62l0
UKTqlqdtuRY
aIe4SUu62l0


http://img02.picoodle.com/img/img02/7/2/20/f_P2140001m_7c2260d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2140001m_7c2260d.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2140002m_4084f5e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2140002m_4084f5e.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2140004m_84c6128.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2140004m_84c6128.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2140007m_0fc9ab5.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2140007m_0fc9ab5.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2140001m_32664ce.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2140001m_32664ce.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2140002m_1f36903.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2140002m_1f36903.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2140007m_98c09e6.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2140007m_98c09e6.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2140010m_b33db0d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2140010m_b33db0d.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2140011m_3baa6d3.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2140011m_3baa6d3.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2140014m_9154fd2.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2140014m_9154fd2.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2140016m_a41e377.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2140016m_a41e377.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2140017m_a85e4a3.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2140017m_a85e4a3.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2150013m_0c6225e.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2150013m_0c6225e.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160005m_4637258.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160005m_4637258.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160001m_753c4bf.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160001m_753c4bf.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160002m_744417c.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160002m_744417c.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160003m_2c4350c.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160003m_2c4350c.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2160004m_b47e2e5.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2160004m_b47e2e5.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160004m_1c03304.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160004m_1c03304.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160005m_c0cbeb8.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160005m_c0cbeb8.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160008m_131e701.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160008m_131e701.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160010m_65115c7.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160010m_65115c7.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160011m_924ef96.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160011m_924ef96.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2160012m_3fc6539.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2160012m_3fc6539.jpg)

[pedrofilho]

http://img02.picoodle.com/img/img02/7/2/20/f_P2160001m_56df666.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160001m_56df666.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160002m_09abfce.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160002m_09abfce.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2160007m_6f2c747.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2160007m_6f2c747.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2160008m_7441aa8.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2160008m_7441aa8.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160009m_73efe76.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160009m_73efe76.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160010m_08aa971.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160010m_08aa971.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160011m_8bcbd4d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160011m_8bcbd4d.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160002m_939a8cf.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160002m_939a8cf.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160003m_dff9f7f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160003m_dff9f7f.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160005m_802c185.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160005m_802c185.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160007m_82ec10d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160007m_82ec10d.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160012m_8f27737.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160012m_8f27737.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160013m_ac8d33f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160013m_ac8d33f.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2160014m_6f03c62.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2160014m_6f03c62.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160015m_b2c1096.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160015m_b2c1096.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160016m_127b623.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160016m_127b623.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160017m_bcc0f20.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160017m_bcc0f20.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160002m_ba7025c.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160002m_ba7025c.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160003m_e536431.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160003m_e536431.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2160004m_ca820b9.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2160004m_ca820b9.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160005m_1f82f72.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160005m_1f82f72.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160006m_a910b90.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160006m_a910b90.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160007m_e16cb53.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160007m_e16cb53.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160008m_b2a9759.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160008m_b2a9759.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160009m_f981692.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160009m_f981692.jpg)

[pedrofilho]

http://img02.picoodle.com/img/img02/7/2/20/f_P2160009m_0085841.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160009m_0085841.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2160011m_a78c93d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2160011m_a78c93d.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2160012m_d2a171b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2160012m_d2a171b.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160003m_ca7ec53.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160003m_ca7ec53.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160004m_2d9bf04.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160004m_2d9bf04.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160005m_a60d2fc.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160005m_a60d2fc.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160008m_9d70df9.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160008m_9d70df9.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2160009m_3742d8c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2160009m_3742d8c.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2160010m_f6edbb4.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2160010m_f6edbb4.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160012m_1b8ed78.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160012m_1b8ed78.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160013m_abb76d2.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160013m_abb76d2.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2160014m_da8413b.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2160014m_da8413b.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2160001m_ae9f9cc.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2160001m_ae9f9cc.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2160003m_189f623.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2160003m_189f623.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2170005m_64238a2.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2170005m_64238a2.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2170007m_136b377.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2170007m_136b377.jpg)
http://img01.picoodle.com/img/img01/7/2/20/t_P2170008m_ec65bd5.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2170008m_ec65bd5.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2170009m_7f3c839.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2170009m_7f3c839.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2170010m_716cb04.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2170010m_716cb04.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2170011m_14e992f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2170011m_14e992f.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2170012m_4a9f96d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2170012m_4a9f96d.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2170002m_e28c50c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2170002m_e28c50c.jpg)

[pedrofilho]

http://img03.picoodle.com/img/img03/7/2/20/f_P2170005m_9a68a2e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2170005m_9a68a2e.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2170008m_99eba54.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2170008m_99eba54.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2170010m_5b2b521.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2170010m_5b2b521.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2170011m_fe9b085.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2170011m_fe9b085.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2170003m_6cd2304.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2170003m_6cd2304.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2170006m_ae4b97e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2170006m_ae4b97e.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2170013m_11a2742.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2170013m_11a2742.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2170014m_7cdcca6.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2170014m_7cdcca6.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2170015m_8eeb0d4.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2170015m_8eeb0d4.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2170016m_cdd229f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2170016m_cdd229f.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2170018m_aaa24c9.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2170018m_aaa24c9.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2170019m_9e7d2ee.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2170019m_9e7d2ee.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2170002m_cd459af.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2170002m_cd459af.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2170009m_03a4854.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2170009m_03a4854.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2170012m_0bd7e6b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2170012m_0bd7e6b.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2170014m_e2d93b9.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2170014m_e2d93b9.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2170016m_bd2b9f4.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2170016m_bd2b9f4.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2170018m_5c3ca68.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2170018m_5c3ca68.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2170021m_7350ffa.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2170021m_7350ffa.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2170022m_0d2d45f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2170022m_0d2d45f.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2170001m_b607ee6.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2170001m_b607ee6.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2170002m_f5aa38e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2170002m_f5aa38e.jpg)

[pedrofilho]

http://img01.picoodle.com/img/img01/7/2/20/f_P2170003m_3e6376a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2170003m_3e6376a.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2170004m_3f8a6f1.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2170004m_3f8a6f1.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2180008m_89617bc.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2180008m_89617bc.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2180009m_50519dd.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2180009m_50519dd.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2180010m_d45d5bf.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2180010m_d45d5bf.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2180011m_d5242c6.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2180011m_d5242c6.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2180001m_94c0d56.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2180001m_94c0d56.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2180006m_a5fc0d7.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2180006m_a5fc0d7.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2180007m_d49ba99.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2180007m_d49ba99.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2180008m_b3afddd.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2180008m_b3afddd.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2180009m_c234333.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2180009m_c234333.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2180010m_9106d6b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2180010m_9106d6b.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2180011m_146867d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2180011m_146867d.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2180013m_e523f1d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2180013m_e523f1d.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2180014m_d6ef06b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2180014m_d6ef06b.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2180003m_6190814.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2180003m_6190814.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2180004m_a37e4f3.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2180004m_a37e4f3.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2180005m_28d32ca.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2180005m_28d32ca.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2180006m_165f3d5.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2180006m_165f3d5.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2180007m_7c50c74.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2180007m_7c50c74.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2180008m_a63f9cc.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2180008m_a63f9cc.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2180009m_a3d6b3a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2180009m_a3d6b3a.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2180011m_32a7c17.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2180011m_32a7c17.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2180012m_0fb720a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2180012m_0fb720a.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2180001m_0149dbe.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2180001m_0149dbe.jpg)

[pedrofilho]

http://img03.picoodle.com/img/img03/7/2/20/f_P2180002m_ac40f4e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2180002m_ac40f4e.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2180004m_f98c32f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2180004m_f98c32f.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2180005m_2622cc3.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2180005m_2622cc3.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2180007m_982e2ac.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2180007m_982e2ac.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2180010m_1a2d6ec.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2180010m_1a2d6ec.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2180001m_10c0070.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2180001m_10c0070.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2180002m_34a7934.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2180002m_34a7934.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2180002m_449beb5.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2180002m_449beb5.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2180003m_100c5b8.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2180003m_100c5b8.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2190005m_fd4579e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2190005m_fd4579e.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2190008m_9a1f35f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2190008m_9a1f35f.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2190009m_c615b34.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2190009m_c615b34.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2190012m_7bbb86f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2190012m_7bbb86f.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2190003m_cbd8047.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2190003m_cbd8047.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2190004m_26ac14f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2190004m_26ac14f.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2190005m_3c973ab.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2190005m_3c973ab.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2190009m_e6be2f4.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2190009m_e6be2f4.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2190010m_24072fe.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2190010m_24072fe.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2190012m_b780589.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2190012m_b780589.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2190002m_fa86c91.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2190002m_fa86c91.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2190006m_a4ad8b7.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2190006m_a4ad8b7.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2190007m_b4bcd6b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2190007m_b4bcd6b.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2190010m_e3ffa33.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2190010m_e3ffa33.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2190014m_9d73a3f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2190014m_9d73a3f.jpg)

[pedrofilho]

http://img02.picoodle.com/img/img02/7/2/20/f_P2190016m_66f2092.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2190016m_66f2092.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2190002m_d769a76.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2190002m_d769a76.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2190003m_f48159b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2190003m_f48159b.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2190004m_3ec3806.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2190004m_3ec3806.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2190005m_41c16cd.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2190005m_41c16cd.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2190008m_6b56eb5.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2190008m_6b56eb5.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2190010m_a468d0f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2190010m_a468d0f.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2190012m_00c028c.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2190012m_00c028c.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2190013m_fc0d379.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2190013m_fc0d379.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2190014m_851b577.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2190014m_851b577.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2190001m_965770a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2190001m_965770a.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2190002m_9cdec7e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2190002m_9cdec7e.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2190004m_1579c54.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2190004m_1579c54.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2190007m_eeeb477.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2190007m_eeeb477.jpg)
http://img01.picoodle.com/img/img01/7/2/20/f_P2190008m_62dc32e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/2/20/f_P2190008m_62dc32e.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2190009m_92a2dca.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2190009m_92a2dca.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2190001m_41883d5.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2190001m_41883d5.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2190003m_5812258.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2190003m_5812258.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2190004m_da5fba2.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2190004m_da5fba2.jpg)
http://img03.picoodle.com/img/img03/7/2/20/f_P2190005m_96a375f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/2/20/f_P2190005m_96a375f.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2190007m_1f0f26a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2190007m_1f0f26a.jpg)
http://img02.picoodle.com/img/img02/7/2/20/f_P2190008m_aafe9ef.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/2/20/f_P2190008m_aafe9ef.jpg)

See you soon !

Pedro Torres.

[pedrofilho]

I've said it before, and I'll say it again.. Awesome work Pedro!

Thank you sgtm, this is the best award i can expect, really !

Glad you liked.


ya great stuff that case is BRIGHT! wow. i'm not sure if someone has asked but what is that drink you keep taking pictures with?!?!

:D
Yeah, they already asked, but it's not a problem, acctualy, it's only a tea from herbalife, that gives extra energy and works as anti-oxidant and refreshing for those hard working days...'

And, it's nice..


My guess would be cachaca. Here's what Diamond David Lee Roth has to say about this drink:

They make this drink in Brazil Called cachaca. It's sugar cane alcohol. Costs 35 cents a quart. One quart of that stuff and you see God. Two quarts and you grow a pair of tight pants and an electric guitar!

Dude, it's not cachaça, but my state has the best one, it's called Pitú Gold. And it's mostly exported to Califórnia and Russia. But the best brazilian cachaça is called Ypióca Ouro with is more like a liquor than other thing and is very soft to drink, dispite it's 33% of alchoolic.

If you come to visit my country, do not forget to ask me where to find the best cachaça and will be my pleasure to guide you to a drive trought you'll never forget... I promiss you'll will play better than jimmy... :p

Thanks for you kindly coments, hope you liked the case.



Just do what you're doing; I think we'll manage, and be happy about it!
That is going to be one very bright case, cant wait to see it lit!

Thank you Maz, you aways right. The case pumps lights everywhere, now it's time to do some finishing job to start really the second chapter of case.


Damn! You've been busy! I love the colors and lights, very original ideas there. What was the wire taped to the hard-drive for? An LED?

Oh yeah, that's a thermal sensor for one of those controlers, i really do not remember wich of then is that on pic, but maybe the anyone of the three because all then have these sensors.

Thank you very much, you helped a lot to this work.

See you soon with news about the second chapter of this mod.

Pedro Torres.

[pedrofilho]

pedro this thing is looking beast its so awesome!!! +rep

although i do have a question for you, what is that purple drink that cameos in a vast majoirty of your photos like what drink is it?

Thanks armadilloben, it's herbalife tea, i always drink that after a hard work. Believe me... :D

It gives an extra energy and a faster recover after the work, and the limon one it's delicious... :D

See you !


lol, i was going to ask the same thing, then i thought it might be epoxy resin or something and i'd look stupid :S


hahaha... It's not stupid, but fun... But one thing i learned, those things you said, it's not drinkable, it gives you some mental disturbing... :D

Just tea, called gree-tea. I drink it from herbalife because is easy to do, just drop some on cold water and drink...

See you !

Pedro Torres.

[pedrofilho]

hey the case looks better every time i see it. but how come you didn't water cool the cpu?!

Hey, well, i just think using an aero cooler will improve air circulation on case helping to cool down the temps. Also, it is really beautifull and huge and silent.

If i won some WC solutions from CM contest i´ll do another project cooling down everything with water !

Thanks !


i think the aero flower cpu cooler from zalman is an awesome air cooler and works nearly as well as water cooling. for aesthetics, the aero flower wins!

You´re absolutly rigth ! This cooler i´ve instaled is really eficient on system refrigeration and helps to cool down other components on mobo, like north and south bridge

Thanks !

I´ve started the second part of mod, look the news:


Notebroked:

http://img02.picoodle.com/img/img02/7/3/16/f_P3080019m_9140b60.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/16/f_P3080019m_9140b60.jpg)

http://img01.picoodle.com/img/img01/7/3/16/f_P3080020m_46de840.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/16/f_P3080020m_46de840.jpg)

http://img02.picoodle.com/img/img02/7/3/16/f_P3080021m_6e2a4ba.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/16/f_P3080021m_6e2a4ba.jpg)

http://img03.picoodle.com/img/img03/7/3/16/f_P3080022m_b3a4e7b.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/16/f_P3080022m_b3a4e7b.jpg)

Hot stuff:
http://img03.picoodle.com/img/img03/7/3/16/f_P3040006m_78c7be4.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/16/f_P3040006m_78c7be4.jpg)

http://img02.picoodle.com/img/img02/7/3/16/f_P3040008m_bcf56db.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/16/f_P3040008m_bcf56db.jpg)

http://img03.picoodle.com/img/img03/7/3/16/f_P3040011m_e769c17.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/16/f_P3040011m_e769c17.jpg)

http://img01.picoodle.com/img/img01/7/3/16/f_P3040012m_6f07ac7.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/16/f_P3040012m_6f07ac7.jpg)

A theme relative screw set:
http://img03.picoodle.com/img/img03/7/3/16/f_P3040013m_e4facda.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/16/f_P3040013m_e4facda.jpg)

Analog vga temp display:
http://img03.picoodle.com/img/img03/7/3/16/f_P3040015m_e704e52.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/16/f_P3040015m_e704e52.jpg)

http://img01.picoodle.com/img/img01/7/3/16/f_P3040010m_6d59dd1.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/16/f_P3040010m_6d59dd1.jpg)

http://img03.picoodle.com/img/img03/7/3/16/f_P3060003m_ffc479f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/16/f_P3060003m_ffc479f.jpg)

http://img03.picoodle.com/img/img03/7/3/16/f_P3060004m_03d3853.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/16/f_P3060004m_03d3853.jpg)

Refreshing memos:
http://img01.picoodle.com/img/img01/7/3/16/f_P3060006m_a9f51eb.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/16/f_P3060006m_a9f51eb.jpg)

http://img01.picoodle.com/img/img01/7/3/16/f_P3060009m_5d6b06e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/16/f_P3060009m_5d6b06e.jpg)

http://img01.picoodle.com/img/img01/7/3/16/f_P3060010m_1d2cce8.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/16/f_P3060010m_1d2cce8.jpg)

http://img01.picoodle.com/img/img01/7/3/16/f_P3060013m_3290885.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/16/f_P3060013m_3290885.jpg)

http://img01.picoodle.com/img/img01/7/3/16/f_P3070016m_143d7f2.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/16/f_P3070016m_143d7f2.jpg)

http://img03.picoodle.com/img/img03/7/3/16/f_P3070018m_52d0f27.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/16/f_P3070018m_52d0f27.jpg)

http://img02.picoodle.com/img/img02/7/3/16/f_P3070020m_f4dbbf8.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/16/f_P3070020m_f4dbbf8.jpg)

http://img02.picoodle.com/img/img02/7/3/16/f_P3080001m_56345a8.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/16/f_P3080001m_56345a8.jpg)

http://img01.picoodle.com/img/img01/7/3/16/f_P3080003m_1f3c2fe.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/16/f_P3080003m_1f3c2fe.jpg)

http://img01.picoodle.com/img/img01/7/3/16/f_P3080004m_a2ccace.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/16/f_P3080004m_a2ccace.jpg)

I´ll work on electrical parts, doing sleevings and cable managements.

Also, i´ll do a monitor base on fiberglass.

See you soon...

Pedro Torres.

[pedrofilho]

2nd fase begins:

Video:
mCR4QwS9d7M

Photos:
http://img03.picoodle.com/img/img03/7/3/17/f_P3090020m_4f9fa92.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/17/f_P3090020m_4f9fa92.jpg)

http://img02.picoodle.com/img/img02/7/3/17/f_P3090004m_e35fead.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/17/f_P3090004m_e35fead.jpg)

http://img01.picoodle.com/img/img01/7/3/17/f_P3090015m_17a109c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/17/f_P3090015m_17a109c.jpg)

I´ll fabricate another ET face on transparente plexi so it will not interfere with interior colors and lights, also, i´ll do a base to 19" monitor.

See you soon !

Pedro Torres.

[pedrofilho]

http://img01.picoodle.com/img/img01/7/3/17/f_P3090001m_beff266.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/17/f_P3090001m_beff266.jpg)

http://img01.picoodle.com/img/img01/7/3/17/f_P3090002m_55ca7fb.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/17/f_P3090002m_55ca7fb.jpg)

http://img03.picoodle.com/img/img03/7/3/17/f_P3090002m_fb01e38.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/17/f_P3090002m_fb01e38.jpg)

http://img01.picoodle.com/img/img01/7/3/17/f_P3090010m_8ea558a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/17/f_P3090010m_8ea558a.jpg)

http://img02.picoodle.com/img/img02/7/3/17/f_P3100003m_a1d5480.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/17/f_P3100003m_a1d5480.jpg)

http://img01.picoodle.com/img/img01/7/3/17/f_P3100001m_8ea1a39.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/17/f_P3100001m_8ea1a39.jpg)

http://img01.picoodle.com/img/img01/7/3/17/f_P3100003m_c1d275c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/17/f_P3100003m_c1d275c.jpg)

http://img01.picoodle.com/img/img01/7/3/17/f_P3100005m_255f6ba.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/17/f_P3100005m_255f6ba.jpg)

http://img03.picoodle.com/img/img03/7/3/17/f_P3100009m_516d263.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/17/f_P3100009m_516d263.jpg)

http://img01.picoodle.com/img/img01/7/3/17/f_P3100001m_7627b24.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/17/f_P3100001m_7627b24.jpg)

http://img03.picoodle.com/img/img03/7/3/17/f_P3100003m_cd2750b.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/17/f_P3100003m_cd2750b.jpg)

http://img02.picoodle.com/img/img02/7/3/17/f_P3100005m_5099470.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/17/f_P3100005m_5099470.jpg)

http://img03.picoodle.com/img/img03/7/3/17/f_P3100009m_4a9299d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/17/f_P3100009m_4a9299d.jpg)

Old monitor base changing..
http://img03.picoodle.com/img/img03/7/3/18/f_P3100003m_adaa099.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/18/f_P3100003m_adaa099.jpg)

http://img03.picoodle.com/img/img03/7/3/18/f_P3100007m_03901fb.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/18/f_P3100007m_03901fb.jpg)

http://img01.picoodle.com/img/img01/7/3/18/f_P3100008m_3441aa9.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/18/f_P3100008m_3441aa9.jpg)

http://img01.picoodle.com/img/img01/7/3/18/f_P3100009m_32c436e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/18/f_P3100009m_32c436e.jpg)

http://img03.picoodle.com/img/img03/7/3/18/f_P3100013m_c9549e6.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/18/f_P3100013m_c9549e6.jpg)

http://img03.picoodle.com/img/img03/7/3/18/f_P3100017m_861e5a3.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/18/f_P3100017m_861e5a3.jpg)

http://img03.picoodle.com/img/img03/7/3/18/f_P3100023m_3ab7f81.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/18/f_P3100023m_3ab7f81.jpg)

http://img03.picoodle.com/img/img03/7/3/18/f_P3100027m_3716265.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/18/f_P3100027m_3716265.jpg)

[pedrofilho]

Cool, dude! Very creative reservoir and top-piece. I like the mod so far, but wonder if you may have a bit too many colors going on in there. Just my opinion, still a great mod!


Thanks for ur kindly coment jdbnsn,

I'll do an airbrush job yet. Will paint the front panels tools with yellow and case body with a metal cotè paint, aluminium polished, natural shadows, titanium white, yellow ocre...

The cable sleeving i´ll do will contribute for color correction.

The colors will fit at the end of work, at this moment, it is like a mess of colors witch no sense at all.

glad you aproved the alien pieces.

See you !

Pedro Torres.

[pedrofilho]

I should have learned by now to reserve my comments until the job is finished. Carry on my Brazilian friend!

P.S. How was Carnivale?

Don&#180;t let your coments to the end, i really apreciate you accurate observations. Colors are really one of my concern and now i really know it proceeds.

Carnivale was explendorous, amazing, fantastic !! :P

You miss...

Thank you very much,

Pedro Torres.

Feet developments. I&#180;ll do the same texture i used on case, so, i&#180;ll test the airbrush paint i&#180;ll use there on this base:

http://img02.picoodle.com/img/img02/7/3/19/f_P3110003m_be664b7.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/f_P3110003m_be664b7.jpg)

http://img01.picoodle.com/img/img01/7/3/19/f_P3110005m_cb06484.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/19/f_P3110005m_cb06484.jpg)

http://img03.picoodle.com/img/img03/7/3/19/f_P3110007m_b1ae87a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/f_P3110007m_b1ae87a.jpg)

Thank you !

Pedro Torres.

Edit: One thing i forgot to tell:

NV 7900GTX GPU TEMPS BEFORE AQUAGATE-VIVA on CSS:
IDLE: 54~56
FULL: 70~76

AFTER AQUAGATE-VIVA on CSS:
IDLE: 46~47
FULL: 57~58

STUNTING RESULTS !

Nice to over now !

:P

[pedrofilho]

Just received the news of a new sporsorship, won 2 sata blue UV reactive cables from www.SellTech.com.br

Fabrication of monitor base and instalation of na analog thermometer:

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110005m_11ee8cd.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110005m_11ee8cd.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110007m_d676ba1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110007m_d676ba1.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110001m_a59a4a0.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110001m_a59a4a0.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110004m_818e4f3.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110004m_818e4f3.jpg)

http://img01.picoodle.com/img/img01/7/3/19/pedrotorresfilho/f_P3110005m_73f9d70.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/19/pedrotorresfilho/f_P3110005m_73f9d70.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110006m_f1a1f04.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110006m_f1a1f04.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110008m_758d025.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110008m_758d025.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110009m_7d3f55d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110009m_7d3f55d.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110012m_3aed02e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110012m_3aed02e.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110023m_c383e61.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110023m_c383e61.jpg)

Best regards,

Pedro Torres.

[pedrofilho]

Just received the news of a new sporsorship, won 2 sata blue UV reactive cables from www.SellTech.com.br

Fabrication of monitor base and instalation of na analog thermometer:

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110005m_11ee8cd.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110005m_11ee8cd.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110007m_d676ba1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110007m_d676ba1.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110001m_a59a4a0.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110001m_a59a4a0.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110004m_818e4f3.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110004m_818e4f3.jpg)

http://img01.picoodle.com/img/img01/7/3/19/pedrotorresfilho/f_P3110005m_73f9d70.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/19/pedrotorresfilho/f_P3110005m_73f9d70.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110006m_f1a1f04.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110006m_f1a1f04.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110008m_758d025.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110008m_758d025.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110009m_7d3f55d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110009m_7d3f55d.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110012m_3aed02e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110012m_3aed02e.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110023m_c383e61.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110023m_c383e61.jpg)

Best regards,

Pedro Torres.

[pedrofilho]

Just received the news of a new sporsorship, won 2 sata blue UV reactive cables from www.SellTech.com.br

Fabrication of monitor base and instalation of na analog thermometer:

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110005m_11ee8cd.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110005m_11ee8cd.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110007m_d676ba1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110007m_d676ba1.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110001m_a59a4a0.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110001m_a59a4a0.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110004m_818e4f3.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110004m_818e4f3.jpg)

http://img01.picoodle.com/img/img01/7/3/19/pedrotorresfilho/f_P3110005m_73f9d70.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/19/pedrotorresfilho/f_P3110005m_73f9d70.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110006m_f1a1f04.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110006m_f1a1f04.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110008m_758d025.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110008m_758d025.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110009m_7d3f55d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110009m_7d3f55d.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110012m_3aed02e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110012m_3aed02e.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110023m_c383e61.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110023m_c383e61.jpg)

Best regards,

Pedro Torres.

[pedrofilho]

Just received the news of a new sporsorship, won 2 sata blue UV reactive cables from www.SellTech.com.br

Fabrication of monitor base and instalation of na analog thermometer:

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110005m_11ee8cd.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110005m_11ee8cd.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110007m_d676ba1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110007m_d676ba1.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110001m_a59a4a0.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110001m_a59a4a0.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110004m_818e4f3.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110004m_818e4f3.jpg)

http://img01.picoodle.com/img/img01/7/3/19/pedrotorresfilho/f_P3110005m_73f9d70.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/19/pedrotorresfilho/f_P3110005m_73f9d70.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110006m_f1a1f04.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110006m_f1a1f04.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110008m_758d025.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110008m_758d025.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110009m_7d3f55d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110009m_7d3f55d.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110012m_3aed02e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110012m_3aed02e.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110023m_c383e61.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110023m_c383e61.jpg)

Best regards,

Pedro Torres.

[pedrofilho]

Just received the news of a new sporsorship, won 2 sata blue UV reactive cables from www.SellTech.com.br

Fabrication of monitor base and instalation of na analog thermometer:

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110005m_11ee8cd.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110005m_11ee8cd.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110007m_d676ba1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110007m_d676ba1.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110001m_a59a4a0.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110001m_a59a4a0.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110004m_818e4f3.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110004m_818e4f3.jpg)

http://img01.picoodle.com/img/img01/7/3/19/pedrotorresfilho/f_P3110005m_73f9d70.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/19/pedrotorresfilho/f_P3110005m_73f9d70.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110006m_f1a1f04.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110006m_f1a1f04.jpg)

http://img02.picoodle.com/img/img02/7/3/19/pedrotorresfilho/f_P3110008m_758d025.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/19/pedrotorresfilho/f_P3110008m_758d025.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110009m_7d3f55d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110009m_7d3f55d.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110012m_3aed02e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110012m_3aed02e.jpg)

http://img03.picoodle.com/img/img03/7/3/19/pedrotorresfilho/f_P3110023m_c383e61.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/19/pedrotorresfilho/f_P3110023m_c383e61.jpg)

Best regards,

Pedro Torres.

[pedrofilho]

http://img01.picoodle.com/img/img01/7/3/20/pedrotorresfilho/f_P3120005m_fa8bca4.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/20/pedrotorresfilho/f_P3120005m_fa8bca4.jpg)

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120009m_8641437.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120009m_8641437.jpg)

http://img03.picoodle.com/img/img03/7/3/20/pedrotorresfilho/f_P3120010m_c37633a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/20/pedrotorresfilho/f_P3120010m_c37633a.jpg)

http://img01.picoodle.com/img/img01/7/3/20/pedrotorresfilho/f_P3120013m_926e30d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/20/pedrotorresfilho/f_P3120013m_926e30d.jpg)

[pedrofilho]

http://img01.picoodle.com/img/img01/7/3/20/pedrotorresfilho/f_P3120005m_fa8bca4.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/20/pedrotorresfilho/f_P3120005m_fa8bca4.jpg)

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120009m_8641437.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120009m_8641437.jpg)

http://img03.picoodle.com/img/img03/7/3/20/pedrotorresfilho/f_P3120010m_c37633a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/20/pedrotorresfilho/f_P3120010m_c37633a.jpg)

http://img01.picoodle.com/img/img01/7/3/20/pedrotorresfilho/f_P3120013m_926e30d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/20/pedrotorresfilho/f_P3120013m_926e30d.jpg)

[pedrofilho]

http://img01.picoodle.com/img/img01/7/3/20/pedrotorresfilho/f_P3120005m_fa8bca4.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/20/pedrotorresfilho/f_P3120005m_fa8bca4.jpg)

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120009m_8641437.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120009m_8641437.jpg)

http://img03.picoodle.com/img/img03/7/3/20/pedrotorresfilho/f_P3120010m_c37633a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/20/pedrotorresfilho/f_P3120010m_c37633a.jpg)

http://img01.picoodle.com/img/img01/7/3/20/pedrotorresfilho/f_P3120013m_926e30d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/20/pedrotorresfilho/f_P3120013m_926e30d.jpg)

[pedrofilho]

http://img01.picoodle.com/img/img01/7/3/20/pedrotorresfilho/f_P3120005m_fa8bca4.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/20/pedrotorresfilho/f_P3120005m_fa8bca4.jpg)

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120009m_8641437.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120009m_8641437.jpg)

http://img03.picoodle.com/img/img03/7/3/20/pedrotorresfilho/f_P3120010m_c37633a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/20/pedrotorresfilho/f_P3120010m_c37633a.jpg)

http://img01.picoodle.com/img/img01/7/3/20/pedrotorresfilho/f_P3120013m_926e30d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/20/pedrotorresfilho/f_P3120013m_926e30d.jpg)

[pedrofilho]

http://img01.picoodle.com/img/img01/7/3/20/pedrotorresfilho/f_P3120005m_fa8bca4.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/20/pedrotorresfilho/f_P3120005m_fa8bca4.jpg)

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120009m_8641437.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120009m_8641437.jpg)

http://img03.picoodle.com/img/img03/7/3/20/pedrotorresfilho/f_P3120010m_c37633a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/20/pedrotorresfilho/f_P3120010m_c37633a.jpg)

http://img01.picoodle.com/img/img01/7/3/20/pedrotorresfilho/f_P3120013m_926e30d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/20/pedrotorresfilho/f_P3120013m_926e30d.jpg)

[pedrofilho]

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg)

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg)

[pedrofilho]

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg)

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg)

[pedrofilho]

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg)

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg)

[pedrofilho]

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg)

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg)

[pedrofilho]

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg)

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg)

[pedrofilho]

This stuff makes me postergate the painting of monitor base for tomorrow. I only found it around midnight and get sleepy, so, i decided do the paint job tomorrow morning.

http://img01.picoodle.com/img/img01/7/3/20/pedrotorresfilho/f_P3130003m_6a3b2ee.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/20/pedrotorresfilho/f_P3130003m_6a3b2ee.jpg)

See you tomorrow

Pedro Torres.

[pedrofilho]

This stuff makes me postergate the painting of monitor base for tomorrow. I only found it around midnight and get sleepy, so, i decided do the paint job tomorrow morning.

http://img01.picoodle.com/img/img01/7/3/20/pedrotorresfilho/f_P3130003m_6a3b2ee.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/20/pedrotorresfilho/f_P3130003m_6a3b2ee.jpg)

See you tomorrow

Pedro Torres.

[pedrofilho]

This stuff makes me postergate the painting of monitor base for tomorrow. I only found it around midnight and get sleepy, so, i decided do the paint job tomorrow morning.

http://img01.picoodle.com/img/img01/7/3/20/pedrotorresfilho/f_P3130003m_6a3b2ee.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/20/pedrotorresfilho/f_P3130003m_6a3b2ee.jpg)

See you tomorrow

Pedro Torres.

[pedrofilho]

This stuff makes me postergate the painting of monitor base for tomorrow. I only found it around midnight and get sleepy, so, i decided do the paint job tomorrow morning.

http://img01.picoodle.com/img/img01/7/3/20/pedrotorresfilho/f_P3130003m_6a3b2ee.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/20/pedrotorresfilho/f_P3130003m_6a3b2ee.jpg)

See you tomorrow

Pedro Torres.

[pedrofilho]

This stuff makes me postergate the painting of monitor base for tomorrow. I only found it around midnight and get sleepy, so, i decided do the paint job tomorrow morning.

http://img01.picoodle.com/img/img01/7/3/20/pedrotorresfilho/f_P3130003m_6a3b2ee.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/20/pedrotorresfilho/f_P3130003m_6a3b2ee.jpg)

See you tomorrow

Pedro Torres.

[Spawn-Inc]

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg)

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg)

do you have an air compressor?!?! if you do then you can drill a hole in the bottem center of that can and put a fittings and then you will never have to buy another can of aerosol.

WARNING!!!!! do this at your own risk! if you do try this obviously make sure the can is empty. when drilling into the can do it ONLY in the bottem center. and when drilling put the airbrush adaptor on and leave the hose open to the air. but more so where FULL protection, gloves, eye, apron, and a mask. i learned my lesson the hard way. they put a chemical called "Allyl Isothiocyanate" aka mustard oil inside. this chemical BURNS!!! alot and fast. when i was drilling into the can it started smelling funky and very unpleasant. i did this inside, which i do not recommend. if you get this stuff on you then use water to get it off. i ran to the tap and washed it off with water, cold water. it seemed to do the trick. i got it on my hand and neck. it left a red rash for an hour or so. if you attempt to do this i would place the can unside down. i washed the rest of the stuff inside the can with water. i then took the grill off my small bbq and placed the can on top and wrapped the top with the plastic valve with wet paper towel. i attempted to boil off the rest of the water so the can doesn't rust. i got most out but not all.

pictures
http://img92.imageshack.us/img92/9513/propellantmodev7.th.jpg (http://img92.imageshack.us/my.php?image=propellantmodev7.jpg)
http://img293.imageshack.us/img293/2829/propellantmod3au0.th.jpg (http://img293.imageshack.us/my.php?image=propellantmod3au0.jpg)
use teflon tape if you try it for the air compressor fitting. make sure not to over tighten as the metal is thin and can easily strip the thread.
http://img412.imageshack.us/img412/1953/propellantmod2ml1.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod2ml1.jpg)

those purple spots are from the mustard oil. i'm not sure if thats the colour of it or it reacting to the paint. but now that i really think of it i don't think it was becuase of that. i think its just purple paint.
http://img412.imageshack.us/img412/8986/propellantmod1zg4.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod1zg4.jpg)

then for a "power source" i grabbed a empty tank they used for the drive clean and welded a nut onto it, added a air compressor fitting and now have a portable tank of compressed air. here are some pictures of it.
http://inlinethumb59.webshots.com/1274/2732893440100511463S600x600Q85.jpg
http://inlinethumb04.webshots.com/579/2360267220100511463S600x600Q85.jpg
yes the weld ain't pretty but it doesn't leak. i did this with one other tank and i have to weld it then braze it to get it to stop leaking. this one didn't leak at all. i did it with oxy- acetylene. also while i was welding i looked away for a second and blew a hole right threw it. so i had to patch it back up.
http://inlinethumb08.webshots.com/1159/2070901950100511463S600x600Q85.jpg

[Spawn-Inc]

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg)

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg)

do you have an air compressor?!?! if you do then you can drill a hole in the bottem center of that can and put a fittings and then you will never have to buy another can of aerosol.

WARNING!!!!! do this at your own risk! if you do try this obviously make sure the can is empty. when drilling into the can do it ONLY in the bottem center. and when drilling put the airbrush adaptor on and leave the hose open to the air. but more so where FULL protection, gloves, eye, apron, and a mask. i learned my lesson the hard way. they put a chemical called "Allyl Isothiocyanate" aka mustard oil inside. this chemical BURNS!!! alot and fast. when i was drilling into the can it started smelling funky and very unpleasant. i did this inside, which i do not recommend. if you get this stuff on you then use water to get it off. i ran to the tap and washed it off with water, cold water. it seemed to do the trick. i got it on my hand and neck. it left a red rash for an hour or so. if you attempt to do this i would place the can unside down. i washed the rest of the stuff inside the can with water. i then took the grill off my small bbq and placed the can on top and wrapped the top with the plastic valve with wet paper towel. i attempted to boil off the rest of the water so the can doesn't rust. i got most out but not all.

pictures
http://img92.imageshack.us/img92/9513/propellantmodev7.th.jpg (http://img92.imageshack.us/my.php?image=propellantmodev7.jpg)
http://img293.imageshack.us/img293/2829/propellantmod3au0.th.jpg (http://img293.imageshack.us/my.php?image=propellantmod3au0.jpg)
use teflon tape if you try it for the air compressor fitting. make sure not to over tighten as the metal is thin and can easily strip the thread.
http://img412.imageshack.us/img412/1953/propellantmod2ml1.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod2ml1.jpg)

those purple spots are from the mustard oil. i'm not sure if thats the colour of it or it reacting to the paint. but now that i really think of it i don't think it was becuase of that. i think its just purple paint.
http://img412.imageshack.us/img412/8986/propellantmod1zg4.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod1zg4.jpg)

then for a "power source" i grabbed a empty tank they used for the drive clean and welded a nut onto it, added a air compressor fitting and now have a portable tank of compressed air. here are some pictures of it.
http://inlinethumb59.webshots.com/1274/2732893440100511463S600x600Q85.jpg
http://inlinethumb04.webshots.com/579/2360267220100511463S600x600Q85.jpg
yes the weld ain't pretty but it doesn't leak. i did this with one other tank and i have to weld it then braze it to get it to stop leaking. this one didn't leak at all. i did it with oxy- acetylene. also while i was welding i looked away for a second and blew a hole right threw it. so i had to patch it back up.
http://inlinethumb08.webshots.com/1159/2070901950100511463S600x600Q85.jpg

[Spawn-Inc]

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg)

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg)

do you have an air compressor?!?! if you do then you can drill a hole in the bottem center of that can and put a fittings and then you will never have to buy another can of aerosol.

WARNING!!!!! do this at your own risk! if you do try this obviously make sure the can is empty. when drilling into the can do it ONLY in the bottem center. and when drilling put the airbrush adaptor on and leave the hose open to the air. but more so where FULL protection, gloves, eye, apron, and a mask. i learned my lesson the hard way. they put a chemical called "Allyl Isothiocyanate" aka mustard oil inside. this chemical BURNS!!! alot and fast. when i was drilling into the can it started smelling funky and very unpleasant. i did this inside, which i do not recommend. if you get this stuff on you then use water to get it off. i ran to the tap and washed it off with water, cold water. it seemed to do the trick. i got it on my hand and neck. it left a red rash for an hour or so. if you attempt to do this i would place the can unside down. i washed the rest of the stuff inside the can with water. i then took the grill off my small bbq and placed the can on top and wrapped the top with the plastic valve with wet paper towel. i attempted to boil off the rest of the water so the can doesn't rust. i got most out but not all.

pictures
http://img92.imageshack.us/img92/9513/propellantmodev7.th.jpg (http://img92.imageshack.us/my.php?image=propellantmodev7.jpg)
http://img293.imageshack.us/img293/2829/propellantmod3au0.th.jpg (http://img293.imageshack.us/my.php?image=propellantmod3au0.jpg)
use teflon tape if you try it for the air compressor fitting. make sure not to over tighten as the metal is thin and can easily strip the thread.
http://img412.imageshack.us/img412/1953/propellantmod2ml1.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod2ml1.jpg)

those purple spots are from the mustard oil. i'm not sure if thats the colour of it or it reacting to the paint. but now that i really think of it i don't think it was becuase of that. i think its just purple paint.
http://img412.imageshack.us/img412/8986/propellantmod1zg4.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod1zg4.jpg)

then for a "power source" i grabbed a empty tank they used for the drive clean and welded a nut onto it, added a air compressor fitting and now have a portable tank of compressed air. here are some pictures of it.
http://inlinethumb59.webshots.com/1274/2732893440100511463S600x600Q85.jpg
http://inlinethumb04.webshots.com/579/2360267220100511463S600x600Q85.jpg
yes the weld ain't pretty but it doesn't leak. i did this with one other tank and i have to weld it then braze it to get it to stop leaking. this one didn't leak at all. i did it with oxy- acetylene. also while i was welding i looked away for a second and blew a hole right threw it. so i had to patch it back up.
http://inlinethumb08.webshots.com/1159/2070901950100511463S600x600Q85.jpg

[Spawn-Inc]

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg)

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg)

do you have an air compressor?!?! if you do then you can drill a hole in the bottem center of that can and put a fittings and then you will never have to buy another can of aerosol.

WARNING!!!!! do this at your own risk! if you do try this obviously make sure the can is empty. when drilling into the can do it ONLY in the bottem center. and when drilling put the airbrush adaptor on and leave the hose open to the air. but more so where FULL protection, gloves, eye, apron, and a mask. i learned my lesson the hard way. they put a chemical called "Allyl Isothiocyanate" aka mustard oil inside. this chemical BURNS!!! alot and fast. when i was drilling into the can it started smelling funky and very unpleasant. i did this inside, which i do not recommend. if you get this stuff on you then use water to get it off. i ran to the tap and washed it off with water, cold water. it seemed to do the trick. i got it on my hand and neck. it left a red rash for an hour or so. if you attempt to do this i would place the can unside down. i washed the rest of the stuff inside the can with water. i then took the grill off my small bbq and placed the can on top and wrapped the top with the plastic valve with wet paper towel. i attempted to boil off the rest of the water so the can doesn't rust. i got most out but not all.

pictures
http://img92.imageshack.us/img92/9513/propellantmodev7.th.jpg (http://img92.imageshack.us/my.php?image=propellantmodev7.jpg)
http://img293.imageshack.us/img293/2829/propellantmod3au0.th.jpg (http://img293.imageshack.us/my.php?image=propellantmod3au0.jpg)
use teflon tape if you try it for the air compressor fitting. make sure not to over tighten as the metal is thin and can easily strip the thread.
http://img412.imageshack.us/img412/1953/propellantmod2ml1.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod2ml1.jpg)

those purple spots are from the mustard oil. i'm not sure if thats the colour of it or it reacting to the paint. but now that i really think of it i don't think it was becuase of that. i think its just purple paint.
http://img412.imageshack.us/img412/8986/propellantmod1zg4.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod1zg4.jpg)

then for a "power source" i grabbed a empty tank they used for the drive clean and welded a nut onto it, added a air compressor fitting and now have a portable tank of compressed air. here are some pictures of it.
http://inlinethumb59.webshots.com/1274/2732893440100511463S600x600Q85.jpg
http://inlinethumb04.webshots.com/579/2360267220100511463S600x600Q85.jpg
yes the weld ain't pretty but it doesn't leak. i did this with one other tank and i have to weld it then braze it to get it to stop leaking. this one didn't leak at all. i did it with oxy- acetylene. also while i was welding i looked away for a second and blew a hole right threw it. so i had to patch it back up.
http://inlinethumb08.webshots.com/1159/2070901950100511463S600x600Q85.jpg

[Spawn-Inc]

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120001m_e86d538.jpg)

http://img02.picoodle.com/img/img02/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/20/pedrotorresfilho/f_P3120006m_66a4880.jpg)

do you have an air compressor?!?! if you do then you can drill a hole in the bottem center of that can and put a fittings and then you will never have to buy another can of aerosol.

WARNING!!!!! do this at your own risk! if you do try this obviously make sure the can is empty. when drilling into the can do it ONLY in the bottem center. and when drilling put the airbrush adaptor on and leave the hose open to the air. but more so where FULL protection, gloves, eye, apron, and a mask. i learned my lesson the hard way. they put a chemical called "Allyl Isothiocyanate" aka mustard oil inside. this chemical BURNS!!! alot and fast. when i was drilling into the can it started smelling funky and very unpleasant. i did this inside, which i do not recommend. if you get this stuff on you then use water to get it off. i ran to the tap and washed it off with water, cold water. it seemed to do the trick. i got it on my hand and neck. it left a red rash for an hour or so. if you attempt to do this i would place the can unside down. i washed the rest of the stuff inside the can with water. i then took the grill off my small bbq and placed the can on top and wrapped the top with the plastic valve with wet paper towel. i attempted to boil off the rest of the water so the can doesn't rust. i got most out but not all.

pictures
http://img92.imageshack.us/img92/9513/propellantmodev7.th.jpg (http://img92.imageshack.us/my.php?image=propellantmodev7.jpg)
http://img293.imageshack.us/img293/2829/propellantmod3au0.th.jpg (http://img293.imageshack.us/my.php?image=propellantmod3au0.jpg)
use teflon tape if you try it for the air compressor fitting. make sure not to over tighten as the metal is thin and can easily strip the thread.
http://img412.imageshack.us/img412/1953/propellantmod2ml1.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod2ml1.jpg)

those purple spots are from the mustard oil. i'm not sure if thats the colour of it or it reacting to the paint. but now that i really think of it i don't think it was becuase of that. i think its just purple paint.
http://img412.imageshack.us/img412/8986/propellantmod1zg4.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod1zg4.jpg)

then for a "power source" i grabbed a empty tank they used for the drive clean and welded a nut onto it, added a air compressor fitting and now have a portable tank of compressed air. here are some pictures of it.
http://inlinethumb59.webshots.com/1274/2732893440100511463S600x600Q85.jpg
http://inlinethumb04.webshots.com/579/2360267220100511463S600x600Q85.jpg
yes the weld ain't pretty but it doesn't leak. i did this with one other tank and i have to weld it then braze it to get it to stop leaking. this one didn't leak at all. i did it with oxy- acetylene. also while i was welding i looked away for a second and blew a hole right threw it. so i had to patch it back up.
http://inlinethumb08.webshots.com/1159/2070901950100511463S600x600Q85.jpg

[pedrofilho]

do you have an air compressor?!?! if you do then you can drill a hole in the bottem center of that can and put a fittings and then you will never have to buy another can of aerosol.

WARNING!!!!! if you do try this obviously make sure the can is empty. when drilling into the can do it ONLY in the bottem center. and when drilling put the airbrush adaptor on and leave the hose open to the air. but more so where FULL protection, gloves, eye, apron, and a mask. i learned my lesson the hard way. they put a chemical called "Allyl Isothiocyanate" aka mustard oil. this chemical BURNS!!! alot and fast. when i was drilling into the can it started smelling funky and very unpleasant. i did this inside, which i do not recommend. if you get this stuff on you then use water to get it off. i ran to the tap and washed it off with water, cold water. it seemed to do the trick. i got it on my hand and neck. it left a red rash for an hour or so. if you attempt to do this i would place the can unside down. i washed the rest of the stuff inside the can with water. i then took the grill off my small bbq and placed the can on top and wrapped the top with the plastic valve with wet paper towel. i attempted to boil off the rest of the water so the can doesn't rust. i got most out but not all.

use teflon tape if you try it for the air compressor fitting. make sure not to over tighten as the metal is thin and can easily strip the thread.
http://img412.imageshack.us/img412/1953/propellantmod2ml1.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod2ml1.jpg)


This is exaclty what i am about to do. I boght an tire air pipe and was programing to install it at botton and never more buy another aerosol.

Really thanks for the models you entered, i really apreciated that !

Thank you,

Pedro Torres

Edit:

PS-> The air thank is quite impressive, i am already copying it. Sure i&#180;ll try to do one of this to me...

[pedrofilho]

do you have an air compressor?!?! if you do then you can drill a hole in the bottem center of that can and put a fittings and then you will never have to buy another can of aerosol.

WARNING!!!!! if you do try this obviously make sure the can is empty. when drilling into the can do it ONLY in the bottem center. and when drilling put the airbrush adaptor on and leave the hose open to the air. but more so where FULL protection, gloves, eye, apron, and a mask. i learned my lesson the hard way. they put a chemical called "Allyl Isothiocyanate" aka mustard oil. this chemical BURNS!!! alot and fast. when i was drilling into the can it started smelling funky and very unpleasant. i did this inside, which i do not recommend. if you get this stuff on you then use water to get it off. i ran to the tap and washed it off with water, cold water. it seemed to do the trick. i got it on my hand and neck. it left a red rash for an hour or so. if you attempt to do this i would place the can unside down. i washed the rest of the stuff inside the can with water. i then took the grill off my small bbq and placed the can on top and wrapped the top with the plastic valve with wet paper towel. i attempted to boil off the rest of the water so the can doesn't rust. i got most out but not all.

use teflon tape if you try it for the air compressor fitting. make sure not to over tighten as the metal is thin and can easily strip the thread.
http://img412.imageshack.us/img412/1953/propellantmod2ml1.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod2ml1.jpg)


This is exaclty what i am about to do. I boght an tire air pipe and was programing to install it at botton and never more buy another aerosol.

Really thanks for the models you entered, i really apreciated that !

Thank you,

Pedro Torres

Edit:

PS-> The air thank is quite impressive, i am already copying it. Sure i&#180;ll try to do one of this to me...

[pedrofilho]

do you have an air compressor?!?! if you do then you can drill a hole in the bottem center of that can and put a fittings and then you will never have to buy another can of aerosol.

WARNING!!!!! if you do try this obviously make sure the can is empty. when drilling into the can do it ONLY in the bottem center. and when drilling put the airbrush adaptor on and leave the hose open to the air. but more so where FULL protection, gloves, eye, apron, and a mask. i learned my lesson the hard way. they put a chemical called "Allyl Isothiocyanate" aka mustard oil. this chemical BURNS!!! alot and fast. when i was drilling into the can it started smelling funky and very unpleasant. i did this inside, which i do not recommend. if you get this stuff on you then use water to get it off. i ran to the tap and washed it off with water, cold water. it seemed to do the trick. i got it on my hand and neck. it left a red rash for an hour or so. if you attempt to do this i would place the can unside down. i washed the rest of the stuff inside the can with water. i then took the grill off my small bbq and placed the can on top and wrapped the top with the plastic valve with wet paper towel. i attempted to boil off the rest of the water so the can doesn't rust. i got most out but not all.

use teflon tape if you try it for the air compressor fitting. make sure not to over tighten as the metal is thin and can easily strip the thread.
http://img412.imageshack.us/img412/1953/propellantmod2ml1.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod2ml1.jpg)


This is exaclty what i am about to do. I boght an tire air pipe and was programing to install it at botton and never more buy another aerosol.

Really thanks for the models you entered, i really apreciated that !

Thank you,

Pedro Torres

Edit:

PS-> The air thank is quite impressive, i am already copying it. Sure i&#180;ll try to do one of this to me...

[pedrofilho]

do you have an air compressor?!?! if you do then you can drill a hole in the bottem center of that can and put a fittings and then you will never have to buy another can of aerosol.

WARNING!!!!! if you do try this obviously make sure the can is empty. when drilling into the can do it ONLY in the bottem center. and when drilling put the airbrush adaptor on and leave the hose open to the air. but more so where FULL protection, gloves, eye, apron, and a mask. i learned my lesson the hard way. they put a chemical called "Allyl Isothiocyanate" aka mustard oil. this chemical BURNS!!! alot and fast. when i was drilling into the can it started smelling funky and very unpleasant. i did this inside, which i do not recommend. if you get this stuff on you then use water to get it off. i ran to the tap and washed it off with water, cold water. it seemed to do the trick. i got it on my hand and neck. it left a red rash for an hour or so. if you attempt to do this i would place the can unside down. i washed the rest of the stuff inside the can with water. i then took the grill off my small bbq and placed the can on top and wrapped the top with the plastic valve with wet paper towel. i attempted to boil off the rest of the water so the can doesn't rust. i got most out but not all.

use teflon tape if you try it for the air compressor fitting. make sure not to over tighten as the metal is thin and can easily strip the thread.
http://img412.imageshack.us/img412/1953/propellantmod2ml1.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod2ml1.jpg)


This is exaclty what i am about to do. I boght an tire air pipe and was programing to install it at botton and never more buy another aerosol.

Really thanks for the models you entered, i really apreciated that !

Thank you,

Pedro Torres

Edit:

PS-> The air thank is quite impressive, i am already copying it. Sure i&#180;ll try to do one of this to me...

[pedrofilho]

do you have an air compressor?!?! if you do then you can drill a hole in the bottem center of that can and put a fittings and then you will never have to buy another can of aerosol.

WARNING!!!!! if you do try this obviously make sure the can is empty. when drilling into the can do it ONLY in the bottem center. and when drilling put the airbrush adaptor on and leave the hose open to the air. but more so where FULL protection, gloves, eye, apron, and a mask. i learned my lesson the hard way. they put a chemical called "Allyl Isothiocyanate" aka mustard oil. this chemical BURNS!!! alot and fast. when i was drilling into the can it started smelling funky and very unpleasant. i did this inside, which i do not recommend. if you get this stuff on you then use water to get it off. i ran to the tap and washed it off with water, cold water. it seemed to do the trick. i got it on my hand and neck. it left a red rash for an hour or so. if you attempt to do this i would place the can unside down. i washed the rest of the stuff inside the can with water. i then took the grill off my small bbq and placed the can on top and wrapped the top with the plastic valve with wet paper towel. i attempted to boil off the rest of the water so the can doesn't rust. i got most out but not all.

use teflon tape if you try it for the air compressor fitting. make sure not to over tighten as the metal is thin and can easily strip the thread.
http://img412.imageshack.us/img412/1953/propellantmod2ml1.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod2ml1.jpg)


This is exaclty what i am about to do. I boght an tire air pipe and was programing to install it at botton and never more buy another aerosol.

Really thanks for the models you entered, i really apreciated that !

Thank you,

Pedro Torres

Edit:

PS-> The air thank is quite impressive, i am already copying it. Sure i&#180;ll try to do one of this to me...

[pedrofilho]

Can't wait to see how the painting will look!
:wav: <- this one is really gay, the "lots of collors" stuff...

Thanks dude,

I couldn´t finish the paint job because a compressor failure, tomorrow i´ll fix it and complete de paintings.

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130001m_82eef7c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130001m_82eef7c.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130006m_2277675.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130006m_2277675.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130007m_3579215.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130007m_3579215.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130008m_6db4b2b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130008m_6db4b2b.jpg)

http://img02.picoodle.com/img/img02/7/3/21/pedrotorresfilho/f_P3130009m_b3fd49a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/21/pedrotorresfilho/f_P3130009m_b3fd49a.jpg)

http://img03.picoodle.com/img/img03/7/3/21/pedrotorresfilho/f_P3130009m_6dba952.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/21/pedrotorresfilho/f_P3130009m_6dba952.jpg)

http://img02.picoodle.com/img/img02/7/3/21/pedrotorresfilho/f_P3130010m_2e5d10f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/21/pedrotorresfilho/f_P3130010m_2e5d10f.jpg)

http://img03.picoodle.com/img/img03/7/3/21/pedrotorresfilho/f_P3140012m_0f4860d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/21/pedrotorresfilho/f_P3140012m_0f4860d.jpg)

It works (will try a 2.5l coke reservoir):
http://img02.picoodle.com/img/img02/7/3/21/pedrotorresfilho/f_P3140015m_4fe58d1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/21/pedrotorresfilho/f_P3140015m_4fe58d1.jpg)

http://img03.picoodle.com/img/img03/7/3/21/pedrotorresfilho/f_P3140020m_eafb433.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/21/pedrotorresfilho/f_P3140020m_eafb433.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3140025m_8f22bd6.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3140025m_8f22bd6.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3140001m_e4dc338.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3140001m_e4dc338.jpg)

See you,

Pedro Torres

[pedrofilho]

Can't wait to see how the painting will look!
:wav: <- this one is really gay, the "lots of collors" stuff...

Thanks dude,

I couldn´t finish the paint job because a compressor failure, tomorrow i´ll fix it and complete de paintings.

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130001m_82eef7c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130001m_82eef7c.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130006m_2277675.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130006m_2277675.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130007m_3579215.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130007m_3579215.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130008m_6db4b2b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130008m_6db4b2b.jpg)

http://img02.picoodle.com/img/img02/7/3/21/pedrotorresfilho/f_P3130009m_b3fd49a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/21/pedrotorresfilho/f_P3130009m_b3fd49a.jpg)

http://img03.picoodle.com/img/img03/7/3/21/pedrotorresfilho/f_P3130009m_6dba952.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/21/pedrotorresfilho/f_P3130009m_6dba952.jpg)

http://img02.picoodle.com/img/img02/7/3/21/pedrotorresfilho/f_P3130010m_2e5d10f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/21/pedrotorresfilho/f_P3130010m_2e5d10f.jpg)

http://img03.picoodle.com/img/img03/7/3/21/pedrotorresfilho/f_P3140012m_0f4860d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/21/pedrotorresfilho/f_P3140012m_0f4860d.jpg)

It works (will try a 2.5l coke reservoir):
http://img02.picoodle.com/img/img02/7/3/21/pedrotorresfilho/f_P3140015m_4fe58d1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/21/pedrotorresfilho/f_P3140015m_4fe58d1.jpg)

http://img03.picoodle.com/img/img03/7/3/21/pedrotorresfilho/f_P3140020m_eafb433.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/21/pedrotorresfilho/f_P3140020m_eafb433.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3140025m_8f22bd6.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3140025m_8f22bd6.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3140001m_e4dc338.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3140001m_e4dc338.jpg)

See you,

Pedro Torres

[pedrofilho]

Can't wait to see how the painting will look!
:wav: <- this one is really gay, the "lots of collors" stuff...

Thanks dude,

I couldn´t finish the paint job because a compressor failure, tomorrow i´ll fix it and complete de paintings.

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130001m_82eef7c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130001m_82eef7c.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130006m_2277675.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130006m_2277675.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130007m_3579215.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130007m_3579215.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130008m_6db4b2b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130008m_6db4b2b.jpg)

http://img02.picoodle.com/img/img02/7/3/21/pedrotorresfilho/f_P3130009m_b3fd49a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/21/pedrotorresfilho/f_P3130009m_b3fd49a.jpg)

http://img03.picoodle.com/img/img03/7/3/21/pedrotorresfilho/f_P3130009m_6dba952.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/21/pedrotorresfilho/f_P3130009m_6dba952.jpg)

http://img02.picoodle.com/img/img02/7/3/21/pedrotorresfilho/f_P3130010m_2e5d10f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/21/pedrotorresfilho/f_P3130010m_2e5d10f.jpg)

http://img03.picoodle.com/img/img03/7/3/21/pedrotorresfilho/f_P3140012m_0f4860d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/21/pedrotorresfilho/f_P3140012m_0f4860d.jpg)

It works (will try a 2.5l coke reservoir):
http://img02.picoodle.com/img/img02/7/3/21/pedrotorresfilho/f_P3140015m_4fe58d1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/21/pedrotorresfilho/f_P3140015m_4fe58d1.jpg)

http://img03.picoodle.com/img/img03/7/3/21/pedrotorresfilho/f_P3140020m_eafb433.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/21/pedrotorresfilho/f_P3140020m_eafb433.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3140025m_8f22bd6.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3140025m_8f22bd6.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3140001m_e4dc338.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3140001m_e4dc338.jpg)

See you,

Pedro Torres

[pedrofilho]

Can't wait to see how the painting will look!
:wav: <- this one is really gay, the "lots of collors" stuff...

Thanks dude,

I couldn´t finish the paint job because a compressor failure, tomorrow i´ll fix it and complete de paintings.

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130001m_82eef7c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130001m_82eef7c.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130006m_2277675.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130006m_2277675.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130007m_3579215.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130007m_3579215.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130008m_6db4b2b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130008m_6db4b2b.jpg)

http://img02.picoodle.com/img/img02/7/3/21/pedrotorresfilho/f_P3130009m_b3fd49a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/21/pedrotorresfilho/f_P3130009m_b3fd49a.jpg)

http://img03.picoodle.com/img/img03/7/3/21/pedrotorresfilho/f_P3130009m_6dba952.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/21/pedrotorresfilho/f_P3130009m_6dba952.jpg)

http://img02.picoodle.com/img/img02/7/3/21/pedrotorresfilho/f_P3130010m_2e5d10f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/21/pedrotorresfilho/f_P3130010m_2e5d10f.jpg)

http://img03.picoodle.com/img/img03/7/3/21/pedrotorresfilho/f_P3140012m_0f4860d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/21/pedrotorresfilho/f_P3140012m_0f4860d.jpg)

It works (will try a 2.5l coke reservoir):
http://img02.picoodle.com/img/img02/7/3/21/pedrotorresfilho/f_P3140015m_4fe58d1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/21/pedrotorresfilho/f_P3140015m_4fe58d1.jpg)

http://img03.picoodle.com/img/img03/7/3/21/pedrotorresfilho/f_P3140020m_eafb433.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/21/pedrotorresfilho/f_P3140020m_eafb433.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3140025m_8f22bd6.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3140025m_8f22bd6.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3140001m_e4dc338.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3140001m_e4dc338.jpg)

See you,

Pedro Torres

[pedrofilho]

Can't wait to see how the painting will look!
:wav: <- this one is really gay, the "lots of collors" stuff...

Thanks dude,

I couldn´t finish the paint job because a compressor failure, tomorrow i´ll fix it and complete de paintings.

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130001m_82eef7c.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130001m_82eef7c.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130006m_2277675.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130006m_2277675.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130007m_3579215.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130007m_3579215.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3130008m_6db4b2b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3130008m_6db4b2b.jpg)

http://img02.picoodle.com/img/img02/7/3/21/pedrotorresfilho/f_P3130009m_b3fd49a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/21/pedrotorresfilho/f_P3130009m_b3fd49a.jpg)

http://img03.picoodle.com/img/img03/7/3/21/pedrotorresfilho/f_P3130009m_6dba952.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/21/pedrotorresfilho/f_P3130009m_6dba952.jpg)

http://img02.picoodle.com/img/img02/7/3/21/pedrotorresfilho/f_P3130010m_2e5d10f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/21/pedrotorresfilho/f_P3130010m_2e5d10f.jpg)

http://img03.picoodle.com/img/img03/7/3/21/pedrotorresfilho/f_P3140012m_0f4860d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/21/pedrotorresfilho/f_P3140012m_0f4860d.jpg)

It works (will try a 2.5l coke reservoir):
http://img02.picoodle.com/img/img02/7/3/21/pedrotorresfilho/f_P3140015m_4fe58d1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/21/pedrotorresfilho/f_P3140015m_4fe58d1.jpg)

http://img03.picoodle.com/img/img03/7/3/21/pedrotorresfilho/f_P3140020m_eafb433.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/21/pedrotorresfilho/f_P3140020m_eafb433.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3140025m_8f22bd6.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3140025m_8f22bd6.jpg)

http://img01.picoodle.com/img/img01/7/3/21/pedrotorresfilho/f_P3140001m_e4dc338.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/21/pedrotorresfilho/f_P3140001m_e4dc338.jpg)

See you,

Pedro Torres

[pedrofilho]

does the air pump keep up with you spraying? nice job on the air can too looks air tight!

Yes, and makes a lot of noise. But i can handle this. Yesterday the hope doesn´t support the pressure and broked. I´ll fix it and back to et painting.

Thanks,

Pedro Torres.

[pedrofilho]

does the air pump keep up with you spraying? nice job on the air can too looks air tight!

Yes, and makes a lot of noise. But i can handle this. Yesterday the hope doesn´t support the pressure and broked. I´ll fix it and back to et painting.

Thanks,

Pedro Torres.

[pedrofilho]

does the air pump keep up with you spraying? nice job on the air can too looks air tight!

Yes, and makes a lot of noise. But i can handle this. Yesterday the hope doesn´t support the pressure and broked. I´ll fix it and back to et painting.

Thanks,

Pedro Torres.

[pedrofilho]

does the air pump keep up with you spraying? nice job on the air can too looks air tight!

Yes, and makes a lot of noise. But i can handle this. Yesterday the hope doesn´t support the pressure and broked. I´ll fix it and back to et painting.

Thanks,

Pedro Torres.

[pedrofilho]

does the air pump keep up with you spraying? nice job on the air can too looks air tight!

Yes, and makes a lot of noise. But i can handle this. Yesterday the hope doesn´t support the pressure and broked. I´ll fix it and back to et painting.

Thanks,

Pedro Torres.

[pedrofilho]

+rep for both of you guys !

spawn, that is a great idea man

pedro, as always, another great update !

Its an idea that´s works, really nice.

Thank you, i have not see your post.:)

Best regards,

Pedro Torres.

[pedrofilho]

+rep for both of you guys !

spawn, that is a great idea man

pedro, as always, another great update !

Its an idea that´s works, really nice.

Thank you, i have not see your post.:)

Best regards,

Pedro Torres.

[pedrofilho]

+rep for both of you guys !

spawn, that is a great idea man

pedro, as always, another great update !

Its an idea that´s works, really nice.

Thank you, i have not see your post.:)

Best regards,

Pedro Torres.

[pedrofilho]

+rep for both of you guys !

spawn, that is a great idea man

pedro, as always, another great update !

Its an idea that´s works, really nice.

Thank you, i have not see your post.:)

Best regards,

Pedro Torres.

[pedrofilho]

+rep for both of you guys !

spawn, that is a great idea man

pedro, as always, another great update !

Its an idea that´s works, really nice.

Thank you, i have not see your post.:)

Best regards,

Pedro Torres.

[pedrofilho]

i would just keep getting new cans of aerosol but its like $18 a can. and that price was from 3 or 4 years ago. i guess this is one of the benefits of being cheap/smart.

I&#180;ll make another air reservoir, that i did works, but, don&#180;t hold the air for much time.

I am to try a GLP gas bottle.

Fixed the front panel plexi:
http://img01.picoodle.com/img/img01/7/3/22/pedrotorresfilho/f_P3140007m_c15d3ed.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/22/pedrotorresfilho/f_P3140007m_c15d3ed.jpg)

http://img01.picoodle.com/img/img01/7/3/22/pedrotorresfilho/f_P3140009m_139ca6b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/22/pedrotorresfilho/f_P3140009m_139ca6b.jpg)

Best regards,

Pedro Torres.

[pedrofilho]

i would just keep getting new cans of aerosol but its like $18 a can. and that price was from 3 or 4 years ago. i guess this is one of the benefits of being cheap/smart.

I&#180;ll make another air reservoir, that i did works, but, don&#180;t hold the air for much time.

I am to try a GLP gas bottle.

Fixed the front panel plexi:
http://img01.picoodle.com/img/img01/7/3/22/pedrotorresfilho/f_P3140007m_c15d3ed.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/22/pedrotorresfilho/f_P3140007m_c15d3ed.jpg)

http://img01.picoodle.com/img/img01/7/3/22/pedrotorresfilho/f_P3140009m_139ca6b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/22/pedrotorresfilho/f_P3140009m_139ca6b.jpg)

Best regards,

Pedro Torres.

[pedrofilho]

i would just keep getting new cans of aerosol but its like $18 a can. and that price was from 3 or 4 years ago. i guess this is one of the benefits of being cheap/smart.

I&#180;ll make another air reservoir, that i did works, but, don&#180;t hold the air for much time.

I am to try a GLP gas bottle.

Fixed the front panel plexi:
http://img01.picoodle.com/img/img01/7/3/22/pedrotorresfilho/f_P3140007m_c15d3ed.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/22/pedrotorresfilho/f_P3140007m_c15d3ed.jpg)

http://img01.picoodle.com/img/img01/7/3/22/pedrotorresfilho/f_P3140009m_139ca6b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/22/pedrotorresfilho/f_P3140009m_139ca6b.jpg)

Best regards,

Pedro Torres.

[pedrofilho]

i would just keep getting new cans of aerosol but its like $18 a can. and that price was from 3 or 4 years ago. i guess this is one of the benefits of being cheap/smart.

I&#180;ll make another air reservoir, that i did works, but, don&#180;t hold the air for much time.

I am to try a GLP gas bottle.

Fixed the front panel plexi:
http://img01.picoodle.com/img/img01/7/3/22/pedrotorresfilho/f_P3140007m_c15d3ed.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/22/pedrotorresfilho/f_P3140007m_c15d3ed.jpg)

http://img01.picoodle.com/img/img01/7/3/22/pedrotorresfilho/f_P3140009m_139ca6b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/22/pedrotorresfilho/f_P3140009m_139ca6b.jpg)

Best regards,

Pedro Torres.

[pedrofilho]

i would just keep getting new cans of aerosol but its like $18 a can. and that price was from 3 or 4 years ago. i guess this is one of the benefits of being cheap/smart.

I&#180;ll make another air reservoir, that i did works, but, don&#180;t hold the air for much time.

I am to try a GLP gas bottle.

Fixed the front panel plexi:
http://img01.picoodle.com/img/img01/7/3/22/pedrotorresfilho/f_P3140007m_c15d3ed.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/22/pedrotorresfilho/f_P3140007m_c15d3ed.jpg)

http://img01.picoodle.com/img/img01/7/3/22/pedrotorresfilho/f_P3140009m_139ca6b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/22/pedrotorresfilho/f_P3140009m_139ca6b.jpg)

Best regards,

Pedro Torres.

[pedrofilho]

Since yesterday i was working on project. Removed an old DVD-RW and changed the motherboard, now, the ASUS A8N32-SLI commanding...

On 5 1/4 space that old DVD-RW lets behing i am thinking to put an LCD, but, it´s not definitive.

Some sweet pics:

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3150001m_084186f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3150001m_084186f.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3150002m_b50b781.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3150002m_b50b781.jpg)

Sponsored by www.selltec.com.br:
http://img02.picoodle.com/img/img02/7/3/24/pedrotorresfilho/f_P3150008m_26a9139.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/24/pedrotorresfilho/f_P3150008m_26a9139.jpg)

http://img02.picoodle.com/img/img02/7/3/24/pedrotorresfilho/f_P3160011m_8e476ea.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/24/pedrotorresfilho/f_P3160011m_8e476ea.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3160017m_a2d72fb.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3160017m_a2d72fb.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3160022m_9188400.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3160022m_9188400.jpg)

http://img02.picoodle.com/img/img02/7/3/24/pedrotorresfilho/f_P3160029m_9dd331e.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/24/pedrotorresfilho/f_P3160029m_9dd331e.jpg)

http://img01.picoodle.com/img/img01/7/3/24/pedrotorresfilho/f_P3160002m_8c7d7aa.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/24/pedrotorresfilho/f_P3160002m_8c7d7aa.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3160003m_a54da37.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3160003m_a54da37.jpg)

http://img01.picoodle.com/img/img01/7/3/24/pedrotorresfilho/f_P3160001m_0309766.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/24/pedrotorresfilho/f_P3160001m_0309766.jpg)

Yours,

Pedro Torres.

[pedrofilho]

Since yesterday i was working on project. Removed an old DVD-RW and changed the motherboard, now, the ASUS A8N32-SLI commanding...

On 5 1/4 space that old DVD-RW lets behing i am thinking to put an LCD, but, it´s not definitive.

Some sweet pics:

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3150001m_084186f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3150001m_084186f.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3150002m_b50b781.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3150002m_b50b781.jpg)

Sponsored by www.selltec.com.br:
http://img02.picoodle.com/img/img02/7/3/24/pedrotorresfilho/f_P3150008m_26a9139.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/24/pedrotorresfilho/f_P3150008m_26a9139.jpg)

http://img02.picoodle.com/img/img02/7/3/24/pedrotorresfilho/f_P3160011m_8e476ea.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/24/pedrotorresfilho/f_P3160011m_8e476ea.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3160017m_a2d72fb.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3160017m_a2d72fb.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3160022m_9188400.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3160022m_9188400.jpg)

http://img02.picoodle.com/img/img02/7/3/24/pedrotorresfilho/f_P3160029m_9dd331e.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/24/pedrotorresfilho/f_P3160029m_9dd331e.jpg)

http://img01.picoodle.com/img/img01/7/3/24/pedrotorresfilho/f_P3160002m_8c7d7aa.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/24/pedrotorresfilho/f_P3160002m_8c7d7aa.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3160003m_a54da37.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3160003m_a54da37.jpg)

http://img01.picoodle.com/img/img01/7/3/24/pedrotorresfilho/f_P3160001m_0309766.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/24/pedrotorresfilho/f_P3160001m_0309766.jpg)

Yours,

Pedro Torres.

[pedrofilho]

Since yesterday i was working on project. Removed an old DVD-RW and changed the motherboard, now, the ASUS A8N32-SLI commanding...

On 5 1/4 space that old DVD-RW lets behing i am thinking to put an LCD, but, it´s not definitive.

Some sweet pics:

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3150001m_084186f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3150001m_084186f.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3150002m_b50b781.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3150002m_b50b781.jpg)

Sponsored by www.selltec.com.br:
http://img02.picoodle.com/img/img02/7/3/24/pedrotorresfilho/f_P3150008m_26a9139.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/24/pedrotorresfilho/f_P3150008m_26a9139.jpg)

http://img02.picoodle.com/img/img02/7/3/24/pedrotorresfilho/f_P3160011m_8e476ea.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/24/pedrotorresfilho/f_P3160011m_8e476ea.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3160017m_a2d72fb.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3160017m_a2d72fb.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3160022m_9188400.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3160022m_9188400.jpg)

http://img02.picoodle.com/img/img02/7/3/24/pedrotorresfilho/f_P3160029m_9dd331e.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/24/pedrotorresfilho/f_P3160029m_9dd331e.jpg)

http://img01.picoodle.com/img/img01/7/3/24/pedrotorresfilho/f_P3160002m_8c7d7aa.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/24/pedrotorresfilho/f_P3160002m_8c7d7aa.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3160003m_a54da37.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3160003m_a54da37.jpg)

http://img01.picoodle.com/img/img01/7/3/24/pedrotorresfilho/f_P3160001m_0309766.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/24/pedrotorresfilho/f_P3160001m_0309766.jpg)

Yours,

Pedro Torres.

[pedrofilho]

Since yesterday i was working on project. Removed an old DVD-RW and changed the motherboard, now, the ASUS A8N32-SLI commanding...

On 5 1/4 space that old DVD-RW lets behing i am thinking to put an LCD, but, it´s not definitive.

Some sweet pics:

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3150001m_084186f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3150001m_084186f.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3150002m_b50b781.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3150002m_b50b781.jpg)

Sponsored by www.selltec.com.br:
http://img02.picoodle.com/img/img02/7/3/24/pedrotorresfilho/f_P3150008m_26a9139.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/24/pedrotorresfilho/f_P3150008m_26a9139.jpg)

http://img02.picoodle.com/img/img02/7/3/24/pedrotorresfilho/f_P3160011m_8e476ea.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/24/pedrotorresfilho/f_P3160011m_8e476ea.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3160017m_a2d72fb.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3160017m_a2d72fb.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3160022m_9188400.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3160022m_9188400.jpg)

http://img02.picoodle.com/img/img02/7/3/24/pedrotorresfilho/f_P3160029m_9dd331e.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/24/pedrotorresfilho/f_P3160029m_9dd331e.jpg)

http://img01.picoodle.com/img/img01/7/3/24/pedrotorresfilho/f_P3160002m_8c7d7aa.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/24/pedrotorresfilho/f_P3160002m_8c7d7aa.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3160003m_a54da37.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3160003m_a54da37.jpg)

http://img01.picoodle.com/img/img01/7/3/24/pedrotorresfilho/f_P3160001m_0309766.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/24/pedrotorresfilho/f_P3160001m_0309766.jpg)

Yours,

Pedro Torres.

[pedrofilho]

Since yesterday i was working on project. Removed an old DVD-RW and changed the motherboard, now, the ASUS A8N32-SLI commanding...

On 5 1/4 space that old DVD-RW lets behing i am thinking to put an LCD, but, it´s not definitive.

Some sweet pics:

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3150001m_084186f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3150001m_084186f.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3150002m_b50b781.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3150002m_b50b781.jpg)

Sponsored by www.selltec.com.br:
http://img02.picoodle.com/img/img02/7/3/24/pedrotorresfilho/f_P3150008m_26a9139.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/24/pedrotorresfilho/f_P3150008m_26a9139.jpg)

http://img02.picoodle.com/img/img02/7/3/24/pedrotorresfilho/f_P3160011m_8e476ea.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/24/pedrotorresfilho/f_P3160011m_8e476ea.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3160017m_a2d72fb.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3160017m_a2d72fb.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3160022m_9188400.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3160022m_9188400.jpg)

http://img02.picoodle.com/img/img02/7/3/24/pedrotorresfilho/f_P3160029m_9dd331e.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/24/pedrotorresfilho/f_P3160029m_9dd331e.jpg)

http://img01.picoodle.com/img/img01/7/3/24/pedrotorresfilho/f_P3160002m_8c7d7aa.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/24/pedrotorresfilho/f_P3160002m_8c7d7aa.jpg)

http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_P3160003m_a54da37.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_P3160003m_a54da37.jpg)

http://img01.picoodle.com/img/img01/7/3/24/pedrotorresfilho/f_P3160001m_0309766.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/24/pedrotorresfilho/f_P3160001m_0309766.jpg)

Yours,

Pedro Torres.

[pedrofilho]

I decided to push the system to watch better the font reaction since i believe it is almost breaking his capacity limit barrier. So, i install aquamark3 and get this results:
http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_aquamark240m_c357d0a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_aquamark240m_c357d0a.jpg)

The system remains stable but the font really warm a litlle bit.

Anyway, i thing the results was fine for my system, and, i want compare to others who have the same equipamet i have, to see the diference cooling down the system makes.

Really appreciate any help.

Pedro Torres.

[pedrofilho]

I decided to push the system to watch better the font reaction since i believe it is almost breaking his capacity limit barrier. So, i install aquamark3 and get this results:
http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_aquamark240m_c357d0a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_aquamark240m_c357d0a.jpg)

The system remains stable but the font really warm a litlle bit.

Anyway, i thing the results was fine for my system, and, i want compare to others who have the same equipamet i have, to see the diference cooling down the system makes.

Really appreciate any help.

Pedro Torres.

[pedrofilho]

I decided to push the system to watch better the font reaction since i believe it is almost breaking his capacity limit barrier. So, i install aquamark3 and get this results:
http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_aquamark240m_c357d0a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_aquamark240m_c357d0a.jpg)

The system remains stable but the font really warm a litlle bit.

Anyway, i thing the results was fine for my system, and, i want compare to others who have the same equipamet i have, to see the diference cooling down the system makes.

Really appreciate any help.

Pedro Torres.

[pedrofilho]

I decided to push the system to watch better the font reaction since i believe it is almost breaking his capacity limit barrier. So, i install aquamark3 and get this results:
http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_aquamark240m_c357d0a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_aquamark240m_c357d0a.jpg)

The system remains stable but the font really warm a litlle bit.

Anyway, i thing the results was fine for my system, and, i want compare to others who have the same equipamet i have, to see the diference cooling down the system makes.

Really appreciate any help.

Pedro Torres.

[pedrofilho]

I decided to push the system to watch better the font reaction since i believe it is almost breaking his capacity limit barrier. So, i install aquamark3 and get this results:
http://img03.picoodle.com/img/img03/7/3/24/pedrotorresfilho/f_aquamark240m_c357d0a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/24/pedrotorresfilho/f_aquamark240m_c357d0a.jpg)

The system remains stable but the font really warm a litlle bit.

Anyway, i thing the results was fine for my system, and, i want compare to others who have the same equipamet i have, to see the diference cooling down the system makes.

Really appreciate any help.

Pedro Torres.

[pedrofilho]

i'll take your old motherboard if you want hehe.... the case looks whiter now and clean looking. i likes!

Yeah, they really seems better defined. With this new mobo will easy to organize all those wires.

Also, i´ll fabricate an 12V single wire to conect major pieces together. I´ve already bought two TECH FLEX cable sleeving kits (already with me) and a new font that maybe arrive here in two weeks, when i´ll start a real cable management.

Glad to have you around and hear from you.

Thank You !

Pedro Torres.

[pedrofilho]

i'll take your old motherboard if you want hehe.... the case looks whiter now and clean looking. i likes!

Yeah, they really seems better defined. With this new mobo will easy to organize all those wires.

Also, i´ll fabricate an 12V single wire to conect major pieces together. I´ve already bought two TECH FLEX cable sleeving kits (already with me) and a new font that maybe arrive here in two weeks, when i´ll start a real cable management.

Glad to have you around and hear from you.

Thank You !

Pedro Torres.

[pedrofilho]

i'll take your old motherboard if you want hehe.... the case looks whiter now and clean looking. i likes!

Yeah, they really seems better defined. With this new mobo will easy to organize all those wires.

Also, i´ll fabricate an 12V single wire to conect major pieces together. I´ve already bought two TECH FLEX cable sleeving kits (already with me) and a new font that maybe arrive here in two weeks, when i´ll start a real cable management.

Glad to have you around and hear from you.

Thank You !

Pedro Torres.

[pedrofilho]

i'll take your old motherboard if you want hehe.... the case looks whiter now and clean looking. i likes!

Yeah, they really seems better defined. With this new mobo will easy to organize all those wires.

Also, i´ll fabricate an 12V single wire to conect major pieces together. I´ve already bought two TECH FLEX cable sleeving kits (already with me) and a new font that maybe arrive here in two weeks, when i´ll start a real cable management.

Glad to have you around and hear from you.

Thank You !

Pedro Torres.

[pedrofilho]

i'll take your old motherboard if you want hehe.... the case looks whiter now and clean looking. i likes!

Yeah, they really seems better defined. With this new mobo will easy to organize all those wires.

Also, i´ll fabricate an 12V single wire to conect major pieces together. I´ve already bought two TECH FLEX cable sleeving kits (already with me) and a new font that maybe arrive here in two weeks, when i´ll start a real cable management.

Glad to have you around and hear from you.

Thank You !

Pedro Torres.

[pedrofilho]

Remake of front panel plexi hinges:

http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170001m_0c4820a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170001m_0c4820a.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170003m_51dc7fa.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170003m_51dc7fa.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170005m_af0d205.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170005m_af0d205.jpg)

http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170003m_f4fc907.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170003m_f4fc907.jpg)

Best regards,

Pedro Torres.

BTW-> I ordered the coolermaster musketeer 3 to fill the 5 1/4 'blackhole' left behind by the removed DVD-RW.
http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_RF5ADBK01m_cbd769b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_RF5ADBK01m_cbd769b.jpg)

Quite nice ! :P

[pedrofilho]

Remake of front panel plexi hinges:

http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170001m_0c4820a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170001m_0c4820a.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170003m_51dc7fa.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170003m_51dc7fa.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170005m_af0d205.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170005m_af0d205.jpg)

http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170003m_f4fc907.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170003m_f4fc907.jpg)

Best regards,

Pedro Torres.

BTW-> I ordered the coolermaster musketeer 3 to fill the 5 1/4 'blackhole' left behind by the removed DVD-RW.
http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_RF5ADBK01m_cbd769b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_RF5ADBK01m_cbd769b.jpg)

Quite nice ! :P

[pedrofilho]

Remake of front panel plexi hinges:

http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170001m_0c4820a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170001m_0c4820a.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170003m_51dc7fa.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170003m_51dc7fa.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170005m_af0d205.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170005m_af0d205.jpg)

http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170003m_f4fc907.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170003m_f4fc907.jpg)

Best regards,

Pedro Torres.

BTW-> I ordered the coolermaster musketeer 3 to fill the 5 1/4 'blackhole' left behind by the removed DVD-RW.
http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_RF5ADBK01m_cbd769b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_RF5ADBK01m_cbd769b.jpg)

Quite nice ! :P

[pedrofilho]

Remake of front panel plexi hinges:

http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170001m_0c4820a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170001m_0c4820a.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170003m_51dc7fa.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170003m_51dc7fa.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170005m_af0d205.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170005m_af0d205.jpg)

http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170003m_f4fc907.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170003m_f4fc907.jpg)

Best regards,

Pedro Torres.

BTW-> I ordered the coolermaster musketeer 3 to fill the 5 1/4 'blackhole' left behind by the removed DVD-RW.
http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_RF5ADBK01m_cbd769b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_RF5ADBK01m_cbd769b.jpg)

Quite nice ! :P

[pedrofilho]

Remake of front panel plexi hinges:

http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170001m_0c4820a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170001m_0c4820a.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170003m_51dc7fa.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170003m_51dc7fa.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170005m_af0d205.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170005m_af0d205.jpg)

http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170003m_f4fc907.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170003m_f4fc907.jpg)

Best regards,

Pedro Torres.

BTW-> I ordered the coolermaster musketeer 3 to fill the 5 1/4 'blackhole' left behind by the removed DVD-RW.
http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_RF5ADBK01m_cbd769b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_RF5ADBK01m_cbd769b.jpg)

Quite nice ! :P

[pedrofilho]

Front panel hinges removing:
http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170002m_a3469b0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170002m_a3469b0.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170003m_393f257.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170003m_393f257.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170004m_6953364.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170004m_6953364.jpg)

http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170005m_062c943.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170005m_062c943.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170008m_2252171.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170008m_2252171.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170011m_4681a5d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170011m_4681a5d.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170014m_27a45fc.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170014m_27a45fc.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170016m_95722c8.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170016m_95722c8.jpg)

yours,

Pedro Torres.

[pedrofilho]

Front panel hinges removing:
http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170002m_a3469b0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170002m_a3469b0.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170003m_393f257.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170003m_393f257.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170004m_6953364.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170004m_6953364.jpg)

http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170005m_062c943.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170005m_062c943.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170008m_2252171.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170008m_2252171.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170011m_4681a5d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170011m_4681a5d.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170014m_27a45fc.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170014m_27a45fc.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170016m_95722c8.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170016m_95722c8.jpg)

yours,

Pedro Torres.

[pedrofilho]

Front panel hinges removing:
http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170002m_a3469b0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170002m_a3469b0.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170003m_393f257.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170003m_393f257.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170004m_6953364.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170004m_6953364.jpg)

http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170005m_062c943.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170005m_062c943.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170008m_2252171.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170008m_2252171.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170011m_4681a5d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170011m_4681a5d.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170014m_27a45fc.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170014m_27a45fc.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170016m_95722c8.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170016m_95722c8.jpg)

yours,

Pedro Torres.

[pedrofilho]

Front panel hinges removing:
http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170002m_a3469b0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170002m_a3469b0.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170003m_393f257.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170003m_393f257.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170004m_6953364.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170004m_6953364.jpg)

http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170005m_062c943.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170005m_062c943.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170008m_2252171.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170008m_2252171.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170011m_4681a5d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170011m_4681a5d.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170014m_27a45fc.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170014m_27a45fc.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170016m_95722c8.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170016m_95722c8.jpg)

yours,

Pedro Torres.

[pedrofilho]

Front panel hinges removing:
http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170002m_a3469b0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170002m_a3469b0.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170003m_393f257.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170003m_393f257.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170004m_6953364.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170004m_6953364.jpg)

http://img01.picoodle.com/img/img01/7/3/25/pedrotorresfilho/f_P3170005m_062c943.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/25/pedrotorresfilho/f_P3170005m_062c943.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170008m_2252171.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170008m_2252171.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170011m_4681a5d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170011m_4681a5d.jpg)

http://img02.picoodle.com/img/img02/7/3/25/pedrotorresfilho/f_P3170014m_27a45fc.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/25/pedrotorresfilho/f_P3170014m_27a45fc.jpg)

http://img03.picoodle.com/img/img03/7/3/25/pedrotorresfilho/f_P3170016m_95722c8.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/25/pedrotorresfilho/f_P3170016m_95722c8.jpg)

yours,

Pedro Torres.

[pedrofilho]

I´ve ordered the coolermaster musketeer 3 black, it´s pretty beautifull, take a look:
http://img02.picoodle.com/img/img02/7/3/26/pedrotorresfilho/f_RF5ADBK01m_b341f21.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/26/pedrotorresfilho/f_RF5ADBK01m_b341f21.jpg)

http://img02.picoodle.com/img/img02/7/3/26/pedrotorresfilho/f_RF5ADBK02m_ea20a08.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/26/pedrotorresfilho/f_RF5ADBK02m_ea20a08.jpg)

Olha ela aí...
http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/t_RF5ADBK03m_e93ae61.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_RF5ADBK03m_e93ae61.jpg)

http://img02.picoodle.com/img/img02/7/3/26/pedrotorresfilho/f_RF5ADBK04m_2a5d702.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/26/pedrotorresfilho/f_RF5ADBK04m_2a5d702.jpg)

http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/f_RF5ADBK05m_f472bb4.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_RF5ADBK05m_f472bb4.jpg)

See you soon,

Pedro Torres.

[pedrofilho]

I´ve ordered the coolermaster musketeer 3 black, it´s pretty beautifull, take a look:
http://img02.picoodle.com/img/img02/7/3/26/pedrotorresfilho/f_RF5ADBK01m_b341f21.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/26/pedrotorresfilho/f_RF5ADBK01m_b341f21.jpg)

http://img02.picoodle.com/img/img02/7/3/26/pedrotorresfilho/f_RF5ADBK02m_ea20a08.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/26/pedrotorresfilho/f_RF5ADBK02m_ea20a08.jpg)

Olha ela aí...
http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/t_RF5ADBK03m_e93ae61.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_RF5ADBK03m_e93ae61.jpg)

http://img02.picoodle.com/img/img02/7/3/26/pedrotorresfilho/f_RF5ADBK04m_2a5d702.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/26/pedrotorresfilho/f_RF5ADBK04m_2a5d702.jpg)

http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/f_RF5ADBK05m_f472bb4.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_RF5ADBK05m_f472bb4.jpg)

See you soon,

Pedro Torres.

[pedrofilho]

I´ve ordered the coolermaster musketeer 3 black, it´s pretty beautifull, take a look:
http://img02.picoodle.com/img/img02/7/3/26/pedrotorresfilho/f_RF5ADBK01m_b341f21.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/26/pedrotorresfilho/f_RF5ADBK01m_b341f21.jpg)

http://img02.picoodle.com/img/img02/7/3/26/pedrotorresfilho/f_RF5ADBK02m_ea20a08.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/26/pedrotorresfilho/f_RF5ADBK02m_ea20a08.jpg)

Olha ela aí...
http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/t_RF5ADBK03m_e93ae61.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_RF5ADBK03m_e93ae61.jpg)

http://img02.picoodle.com/img/img02/7/3/26/pedrotorresfilho/f_RF5ADBK04m_2a5d702.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/26/pedrotorresfilho/f_RF5ADBK04m_2a5d702.jpg)

http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/f_RF5ADBK05m_f472bb4.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_RF5ADBK05m_f472bb4.jpg)

See you soon,

Pedro Torres.

[pedrofilho]

I´ve ordered the coolermaster musketeer 3 black, it´s pretty beautifull, take a look:
http://img02.picoodle.com/img/img02/7/3/26/pedrotorresfilho/f_RF5ADBK01m_b341f21.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/26/pedrotorresfilho/f_RF5ADBK01m_b341f21.jpg)

http://img02.picoodle.com/img/img02/7/3/26/pedrotorresfilho/f_RF5ADBK02m_ea20a08.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/26/pedrotorresfilho/f_RF5ADBK02m_ea20a08.jpg)

Olha ela aí...
http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/t_RF5ADBK03m_e93ae61.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_RF5ADBK03m_e93ae61.jpg)

http://img02.picoodle.com/img/img02/7/3/26/pedrotorresfilho/f_RF5ADBK04m_2a5d702.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/26/pedrotorresfilho/f_RF5ADBK04m_2a5d702.jpg)

http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/f_RF5ADBK05m_f472bb4.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_RF5ADBK05m_f472bb4.jpg)

See you soon,

Pedro Torres.

[pedrofilho]

I´ve ordered the coolermaster musketeer 3 black, it´s pretty beautifull, take a look:
http://img02.picoodle.com/img/img02/7/3/26/pedrotorresfilho/f_RF5ADBK01m_b341f21.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/26/pedrotorresfilho/f_RF5ADBK01m_b341f21.jpg)

http://img02.picoodle.com/img/img02/7/3/26/pedrotorresfilho/f_RF5ADBK02m_ea20a08.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/26/pedrotorresfilho/f_RF5ADBK02m_ea20a08.jpg)

Olha ela aí...
http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/t_RF5ADBK03m_e93ae61.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_RF5ADBK03m_e93ae61.jpg)

http://img02.picoodle.com/img/img02/7/3/26/pedrotorresfilho/f_RF5ADBK04m_2a5d702.jpg (http://www.picoodle.com/view.php?srv=img02&img=/7/3/26/pedrotorresfilho/f_RF5ADBK04m_2a5d702.jpg)

http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/f_RF5ADBK05m_f472bb4.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_RF5ADBK05m_f472bb4.jpg)

See you soon,

Pedro Torres.

[pedrofilho]

looks nice. is that a vacuum tube?! how much does one of those go for?


It&#180;s about 40.00 usd. The vacuum tube is vintage kind and will compose the front panel acessories, adding sound fuctionality to it.

This valve works as an attenuator and have lower power cosumition.

It will close the black-hole left behind by the old DVD-RW which is broked.

See you soon,

Pedro Torres.

[pedrofilho]

looks nice. is that a vacuum tube?! how much does one of those go for?


It&#180;s about 40.00 usd. The vacuum tube is vintage kind and will compose the front panel acessories, adding sound fuctionality to it.

This valve works as an attenuator and have lower power cosumition.

It will close the black-hole left behind by the old DVD-RW which is broked.

See you soon,

Pedro Torres.

[pedrofilho]

looks nice. is that a vacuum tube?! how much does one of those go for?


It&#180;s about 40.00 usd. The vacuum tube is vintage kind and will compose the front panel acessories, adding sound fuctionality to it.

This valve works as an attenuator and have lower power cosumition.

It will close the black-hole left behind by the old DVD-RW which is broked.

See you soon,

Pedro Torres.

[pedrofilho]

looks nice. is that a vacuum tube?! how much does one of those go for?


It&#180;s about 40.00 usd. The vacuum tube is vintage kind and will compose the front panel acessories, adding sound fuctionality to it.

This valve works as an attenuator and have lower power cosumition.

It will close the black-hole left behind by the old DVD-RW which is broked.

See you soon,

Pedro Torres.

[pedrofilho]

looks nice. is that a vacuum tube?! how much does one of those go for?


It&#180;s about 40.00 usd. The vacuum tube is vintage kind and will compose the front panel acessories, adding sound fuctionality to it.

This valve works as an attenuator and have lower power cosumition.

It will close the black-hole left behind by the old DVD-RW which is broked.

See you soon,

Pedro Torres.

[pedrofilho]

As the alien movemet appears around 20´s with relativity theory from Einstein, i decided to put some vintage stuff on this case and do a sephia, black and white, paint job.

Tomorrow i´ll place two more leds do iluminate de top alien, as it is today:

http://img01.picoodle.com/img/img01/7/3/26/pedrotorresfilho/f_P3170003m_a38861e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/26/pedrotorresfilho/f_P3170003m_a38861e.jpg)

http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/f_P3170004m_d0e50eb.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_P3170004m_d0e50eb.jpg)

http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/f_P3190008m_7cbc7e4.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_P3190008m_7cbc7e4.jpg)

Yours,

Pedro Torres.

[pedrofilho]

As the alien movemet appears around 20´s with relativity theory from Einstein, i decided to put some vintage stuff on this case and do a sephia, black and white, paint job.

Tomorrow i´ll place two more leds do iluminate de top alien, as it is today:

http://img01.picoodle.com/img/img01/7/3/26/pedrotorresfilho/f_P3170003m_a38861e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/26/pedrotorresfilho/f_P3170003m_a38861e.jpg)

http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/f_P3170004m_d0e50eb.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_P3170004m_d0e50eb.jpg)

http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/f_P3190008m_7cbc7e4.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_P3190008m_7cbc7e4.jpg)

Yours,

Pedro Torres.

[pedrofilho]

As the alien movemet appears around 20´s with relativity theory from Einstein, i decided to put some vintage stuff on this case and do a sephia, black and white, paint job.

Tomorrow i´ll place two more leds do iluminate de top alien, as it is today:

http://img01.picoodle.com/img/img01/7/3/26/pedrotorresfilho/f_P3170003m_a38861e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/26/pedrotorresfilho/f_P3170003m_a38861e.jpg)

http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/f_P3170004m_d0e50eb.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_P3170004m_d0e50eb.jpg)

http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/f_P3190008m_7cbc7e4.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_P3190008m_7cbc7e4.jpg)

Yours,

Pedro Torres.

[pedrofilho]

As the alien movemet appears around 20´s with relativity theory from Einstein, i decided to put some vintage stuff on this case and do a sephia, black and white, paint job.

Tomorrow i´ll place two more leds do iluminate de top alien, as it is today:

http://img01.picoodle.com/img/img01/7/3/26/pedrotorresfilho/f_P3170003m_a38861e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/26/pedrotorresfilho/f_P3170003m_a38861e.jpg)

http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/f_P3170004m_d0e50eb.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_P3170004m_d0e50eb.jpg)

http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/f_P3190008m_7cbc7e4.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_P3190008m_7cbc7e4.jpg)

Yours,

Pedro Torres.

[pedrofilho]

As the alien movemet appears around 20´s with relativity theory from Einstein, i decided to put some vintage stuff on this case and do a sephia, black and white, paint job.

Tomorrow i´ll place two more leds do iluminate de top alien, as it is today:

http://img01.picoodle.com/img/img01/7/3/26/pedrotorresfilho/f_P3170003m_a38861e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/26/pedrotorresfilho/f_P3170003m_a38861e.jpg)

http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/f_P3170004m_d0e50eb.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_P3170004m_d0e50eb.jpg)

http://img03.picoodle.com/img/img03/7/3/26/pedrotorresfilho/f_P3190008m_7cbc7e4.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/26/pedrotorresfilho/f_P3190008m_7cbc7e4.jpg)

Yours,

Pedro Torres.

[pedrofilho]

Started the air reservoir to the airbrush:

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190001m_f5fd87b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190001m_f5fd87b.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190002m_6e61292.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190002m_6e61292.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190004m_bab452a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190004m_bab452a.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190006m_a1af91c.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190006m_a1af91c.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190007m_9029e41.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190007m_9029e41.jpg)

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190012m_f6c5565.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190012m_f6c5565.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190013m_bcf4361.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190013m_bcf4361.jpg)

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190004m_ea278bc.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190004m_ea278bc.jpg)

Tomorrow i´ll put the air valve on the botton and if everything works i´ll do the texture of the oposite side and start to paint the case

See you soon,

Pedro Torres.

[pedrofilho]

Started the air reservoir to the airbrush:

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190001m_f5fd87b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190001m_f5fd87b.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190002m_6e61292.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190002m_6e61292.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190004m_bab452a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190004m_bab452a.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190006m_a1af91c.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190006m_a1af91c.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190007m_9029e41.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190007m_9029e41.jpg)

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190012m_f6c5565.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190012m_f6c5565.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190013m_bcf4361.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190013m_bcf4361.jpg)

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190004m_ea278bc.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190004m_ea278bc.jpg)

Tomorrow i´ll put the air valve on the botton and if everything works i´ll do the texture of the oposite side and start to paint the case

See you soon,

Pedro Torres.

[pedrofilho]

Started the air reservoir to the airbrush:

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190001m_f5fd87b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190001m_f5fd87b.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190002m_6e61292.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190002m_6e61292.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190004m_bab452a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190004m_bab452a.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190006m_a1af91c.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190006m_a1af91c.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190007m_9029e41.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190007m_9029e41.jpg)

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190012m_f6c5565.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190012m_f6c5565.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190013m_bcf4361.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190013m_bcf4361.jpg)

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190004m_ea278bc.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190004m_ea278bc.jpg)

Tomorrow i´ll put the air valve on the botton and if everything works i´ll do the texture of the oposite side and start to paint the case

See you soon,

Pedro Torres.

[pedrofilho]

Started the air reservoir to the airbrush:

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190001m_f5fd87b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190001m_f5fd87b.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190002m_6e61292.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190002m_6e61292.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190004m_bab452a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190004m_bab452a.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190006m_a1af91c.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190006m_a1af91c.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190007m_9029e41.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190007m_9029e41.jpg)

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190012m_f6c5565.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190012m_f6c5565.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190013m_bcf4361.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190013m_bcf4361.jpg)

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190004m_ea278bc.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190004m_ea278bc.jpg)

Tomorrow i´ll put the air valve on the botton and if everything works i´ll do the texture of the oposite side and start to paint the case

See you soon,

Pedro Torres.

[pedrofilho]

Started the air reservoir to the airbrush:

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190001m_f5fd87b.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190001m_f5fd87b.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190002m_6e61292.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190002m_6e61292.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190004m_bab452a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190004m_bab452a.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190006m_a1af91c.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190006m_a1af91c.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190007m_9029e41.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190007m_9029e41.jpg)

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190012m_f6c5565.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190012m_f6c5565.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190013m_bcf4361.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190013m_bcf4361.jpg)

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190004m_ea278bc.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190004m_ea278bc.jpg)

Tomorrow i´ll put the air valve on the botton and if everything works i´ll do the texture of the oposite side and start to paint the case

See you soon,

Pedro Torres.

[pedrofilho]

wow... nicely done. +rep i was going to say i hope it can hold the pressure but your using a tire pump. i use an air compresser at 110+psi

Yes, i am using a tyre pump today i removed the old hose witch was broked in last attempt to use it for painting purposes.

Also, i did the hole on the bottlom of the bottle and tomorrow i&#180;ll put the car kind valve.

Thank you for your nicely coment !

Watch this:

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190002m_9ab6756.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190002m_9ab6756.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190009m_aff2d9e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190009m_aff2d9e.jpg)

See you !

Pedro Torres.

[pedrofilho]

wow... nicely done. +rep i was going to say i hope it can hold the pressure but your using a tire pump. i use an air compresser at 110+psi

Yes, i am using a tyre pump today i removed the old hose witch was broked in last attempt to use it for painting purposes.

Also, i did the hole on the bottlom of the bottle and tomorrow i&#180;ll put the car kind valve.

Thank you for your nicely coment !

Watch this:

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190002m_9ab6756.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190002m_9ab6756.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190009m_aff2d9e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190009m_aff2d9e.jpg)

See you !

Pedro Torres.

[pedrofilho]

wow... nicely done. +rep i was going to say i hope it can hold the pressure but your using a tire pump. i use an air compresser at 110+psi

Yes, i am using a tyre pump today i removed the old hose witch was broked in last attempt to use it for painting purposes.

Also, i did the hole on the bottlom of the bottle and tomorrow i&#180;ll put the car kind valve.

Thank you for your nicely coment !

Watch this:

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190002m_9ab6756.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190002m_9ab6756.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190009m_aff2d9e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190009m_aff2d9e.jpg)

See you !

Pedro Torres.

[pedrofilho]

wow... nicely done. +rep i was going to say i hope it can hold the pressure but your using a tire pump. i use an air compresser at 110+psi

Yes, i am using a tyre pump today i removed the old hose witch was broked in last attempt to use it for painting purposes.

Also, i did the hole on the bottlom of the bottle and tomorrow i&#180;ll put the car kind valve.

Thank you for your nicely coment !

Watch this:

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190002m_9ab6756.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190002m_9ab6756.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190009m_aff2d9e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190009m_aff2d9e.jpg)

See you !

Pedro Torres.

[pedrofilho]

wow... nicely done. +rep i was going to say i hope it can hold the pressure but your using a tire pump. i use an air compresser at 110+psi

Yes, i am using a tyre pump today i removed the old hose witch was broked in last attempt to use it for painting purposes.

Also, i did the hole on the bottlom of the bottle and tomorrow i&#180;ll put the car kind valve.

Thank you for your nicely coment !

Watch this:

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3190002m_9ab6756.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3190002m_9ab6756.jpg)

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3190009m_aff2d9e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3190009m_aff2d9e.jpg)

See you !

Pedro Torres.

[pedrofilho]

You use 110 psi? My air brush is only rated at 50?!?! (never used this airbrush yet, it was a gift...)


BTW, Intrigued by this so +rep!

Mine works up 55psi. This reservoir i´ll give a continuous flux of air without the oscilations from pump.

Last time i used it the hose of pump do not supported the pression and blows, for this reason, tomorrow i´ll change the hose for another more resistent.

Thanks for your visit and nice coments.

Best regards,

Pedro Torres.

[pedrofilho]

You use 110 psi? My air brush is only rated at 50?!?! (never used this airbrush yet, it was a gift...)


BTW, Intrigued by this so +rep!

Mine works up 55psi. This reservoir i´ll give a continuous flux of air without the oscilations from pump.

Last time i used it the hose of pump do not supported the pression and blows, for this reason, tomorrow i´ll change the hose for another more resistent.

Thanks for your visit and nice coments.

Best regards,

Pedro Torres.

[pedrofilho]

You use 110 psi? My air brush is only rated at 50?!?! (never used this airbrush yet, it was a gift...)


BTW, Intrigued by this so +rep!

Mine works up 55psi. This reservoir i´ll give a continuous flux of air without the oscilations from pump.

Last time i used it the hose of pump do not supported the pression and blows, for this reason, tomorrow i´ll change the hose for another more resistent.

Thanks for your visit and nice coments.

Best regards,

Pedro Torres.

[pedrofilho]

You use 110 psi? My air brush is only rated at 50?!?! (never used this airbrush yet, it was a gift...)


BTW, Intrigued by this so +rep!

Mine works up 55psi. This reservoir i´ll give a continuous flux of air without the oscilations from pump.

Last time i used it the hose of pump do not supported the pression and blows, for this reason, tomorrow i´ll change the hose for another more resistent.

Thanks for your visit and nice coments.

Best regards,

Pedro Torres.

[pedrofilho]

You use 110 psi? My air brush is only rated at 50?!?! (never used this airbrush yet, it was a gift...)


BTW, Intrigued by this so +rep!

Mine works up 55psi. This reservoir i´ll give a continuous flux of air without the oscilations from pump.

Last time i used it the hose of pump do not supported the pression and blows, for this reason, tomorrow i´ll change the hose for another more resistent.

Thanks for your visit and nice coments.

Best regards,

Pedro Torres.

[pedrofilho]

Added two more leds to top alien:

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3200005m_9e867b9.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3200005m_9e867b9.jpg)

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3200008m_6446283.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3200008m_6446283.jpg)

See you,

Pedro Torres.

[pedrofilho]

Added two more leds to top alien:

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3200005m_9e867b9.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3200005m_9e867b9.jpg)

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3200008m_6446283.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3200008m_6446283.jpg)

See you,

Pedro Torres.

[pedrofilho]

Added two more leds to top alien:

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3200005m_9e867b9.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3200005m_9e867b9.jpg)

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3200008m_6446283.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3200008m_6446283.jpg)

See you,

Pedro Torres.

[pedrofilho]

Added two more leds to top alien:

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3200005m_9e867b9.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3200005m_9e867b9.jpg)

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3200008m_6446283.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3200008m_6446283.jpg)

See you,

Pedro Torres.

[pedrofilho]

Added two more leds to top alien:

http://img03.picoodle.com/img/img03/7/3/27/pedrotorresfilho/f_P3200005m_9e867b9.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/27/pedrotorresfilho/f_P3200005m_9e867b9.jpg)

http://img01.picoodle.com/img/img01/7/3/27/pedrotorresfilho/f_P3200008m_6446283.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/27/pedrotorresfilho/f_P3200008m_6446283.jpg)

See you,

Pedro Torres.

[Spawn-Inc]

You use 110 psi? My air brush is only rated at 50?!?! (never used this airbrush yet, it was a gift...)


BTW, Intrigued by this so +rep!

i shouldn't say it works at that pressure but rather the tank i have hold that pressure then i regulate it as the can.

here are the old pics i posted before. you can see at the top of the air brush can there is a valve from which i can control the pressure.
http://img92.imageshack.us/img92/9513/propellantmodev7.th.jpg (http://img92.imageshack.us/my.php?image=propellantmodev7.jpg)
http://img293.imageshack.us/img293/2829/propellantmod3au0.th.jpg (http://img293.imageshack.us/my.php?image=propellantmod3au0.jpg)


http://img412.imageshack.us/img412/8986/propellantmod1zg4.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod1zg4.jpg)

http://inlinethumb59.webshots.com/1274/2732893440100511463S600x600Q85.jpg

[Spawn-Inc]

You use 110 psi? My air brush is only rated at 50?!?! (never used this airbrush yet, it was a gift...)


BTW, Intrigued by this so +rep!

i shouldn't say it works at that pressure but rather the tank i have hold that pressure then i regulate it as the can.

here are the old pics i posted before. you can see at the top of the air brush can there is a valve from which i can control the pressure.
http://img92.imageshack.us/img92/9513/propellantmodev7.th.jpg (http://img92.imageshack.us/my.php?image=propellantmodev7.jpg)
http://img293.imageshack.us/img293/2829/propellantmod3au0.th.jpg (http://img293.imageshack.us/my.php?image=propellantmod3au0.jpg)


http://img412.imageshack.us/img412/8986/propellantmod1zg4.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod1zg4.jpg)

http://inlinethumb59.webshots.com/1274/2732893440100511463S600x600Q85.jpg

[Spawn-Inc]

You use 110 psi? My air brush is only rated at 50?!?! (never used this airbrush yet, it was a gift...)


BTW, Intrigued by this so +rep!

i shouldn't say it works at that pressure but rather the tank i have hold that pressure then i regulate it as the can.

here are the old pics i posted before. you can see at the top of the air brush can there is a valve from which i can control the pressure.
http://img92.imageshack.us/img92/9513/propellantmodev7.th.jpg (http://img92.imageshack.us/my.php?image=propellantmodev7.jpg)
http://img293.imageshack.us/img293/2829/propellantmod3au0.th.jpg (http://img293.imageshack.us/my.php?image=propellantmod3au0.jpg)


http://img412.imageshack.us/img412/8986/propellantmod1zg4.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod1zg4.jpg)

http://inlinethumb59.webshots.com/1274/2732893440100511463S600x600Q85.jpg

[Spawn-Inc]

You use 110 psi? My air brush is only rated at 50?!?! (never used this airbrush yet, it was a gift...)


BTW, Intrigued by this so +rep!

i shouldn't say it works at that pressure but rather the tank i have hold that pressure then i regulate it as the can.

here are the old pics i posted before. you can see at the top of the air brush can there is a valve from which i can control the pressure.
http://img92.imageshack.us/img92/9513/propellantmodev7.th.jpg (http://img92.imageshack.us/my.php?image=propellantmodev7.jpg)
http://img293.imageshack.us/img293/2829/propellantmod3au0.th.jpg (http://img293.imageshack.us/my.php?image=propellantmod3au0.jpg)


http://img412.imageshack.us/img412/8986/propellantmod1zg4.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod1zg4.jpg)

http://inlinethumb59.webshots.com/1274/2732893440100511463S600x600Q85.jpg

[Spawn-Inc]

You use 110 psi? My air brush is only rated at 50?!?! (never used this airbrush yet, it was a gift...)


BTW, Intrigued by this so +rep!

i shouldn't say it works at that pressure but rather the tank i have hold that pressure then i regulate it as the can.

here are the old pics i posted before. you can see at the top of the air brush can there is a valve from which i can control the pressure.
http://img92.imageshack.us/img92/9513/propellantmodev7.th.jpg (http://img92.imageshack.us/my.php?image=propellantmodev7.jpg)
http://img293.imageshack.us/img293/2829/propellantmod3au0.th.jpg (http://img293.imageshack.us/my.php?image=propellantmod3au0.jpg)


http://img412.imageshack.us/img412/8986/propellantmod1zg4.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod1zg4.jpg)

http://inlinethumb59.webshots.com/1274/2732893440100511463S600x600Q85.jpg

[pedrofilho]

i shouldn't say it works at that pressure but rather the tank i have hold that pressure then i regulate it as the can.

here are the old pics i posted before. you can see at the top of the air brush can there is a valve from which i can control the pressure.
http://img92.imageshack.us/img92/9513/propellantmodev7.th.jpg (http://img92.imageshack.us/my.php?image=propellantmodev7.jpg)

http://img293.imageshack.us/img293/2829/propellantmod3au0.th.jpg (http://img293.imageshack.us/my.php?image=propellantmod3au0.jpg)


http://img412.imageshack.us/img412/8986/propellantmod1zg4.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod1zg4.jpg)

http://inlinethumb59.webshots.com/1274/2732893440100511463S600x600Q85.jpg


I say thank you for your kindly observations and for the tips.

Really soon i´ll bring very nice updates as the air compressor system i am mounting is going just fine.

I did the lung screw cover system and tomorrow i´ll put the botton valve and finish the compressor for the airbrush works.

The cover with regulator screw mounting:http://img01.picoodle.com/img/img01/7/3/28/pedrotorresfilho/f_P3200003m_2d6bfa6.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/28/pedrotorresfilho/f_P3200003m_2d6bfa6.jpg)

Just a better shot of top alien (still miss 1 led)
http://img01.picoodle.com/img/img01/7/3/28/pedrotorresfilho/f_P3200011m_3e7dcc8.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/28/pedrotorresfilho/f_P3200011m_3e7dcc8.jpg)

Now i am going to bed, see you tomorrow !

Thanks,

Pedro Torres.

[pedrofilho]

i shouldn't say it works at that pressure but rather the tank i have hold that pressure then i regulate it as the can.

here are the old pics i posted before. you can see at the top of the air brush can there is a valve from which i can control the pressure.
http://img92.imageshack.us/img92/9513/propellantmodev7.th.jpg (http://img92.imageshack.us/my.php?image=propellantmodev7.jpg)

http://img293.imageshack.us/img293/2829/propellantmod3au0.th.jpg (http://img293.imageshack.us/my.php?image=propellantmod3au0.jpg)


http://img412.imageshack.us/img412/8986/propellantmod1zg4.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod1zg4.jpg)

http://inlinethumb59.webshots.com/1274/2732893440100511463S600x600Q85.jpg


I say thank you for your kindly observations and for the tips.

Really soon i´ll bring very nice updates as the air compressor system i am mounting is going just fine.

I did the lung screw cover system and tomorrow i´ll put the botton valve and finish the compressor for the airbrush works.

The cover with regulator screw mounting:http://img01.picoodle.com/img/img01/7/3/28/pedrotorresfilho/f_P3200003m_2d6bfa6.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/28/pedrotorresfilho/f_P3200003m_2d6bfa6.jpg)

Just a better shot of top alien (still miss 1 led)
http://img01.picoodle.com/img/img01/7/3/28/pedrotorresfilho/f_P3200011m_3e7dcc8.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/28/pedrotorresfilho/f_P3200011m_3e7dcc8.jpg)

Now i am going to bed, see you tomorrow !

Thanks,

Pedro Torres.

[pedrofilho]

i shouldn't say it works at that pressure but rather the tank i have hold that pressure then i regulate it as the can.

here are the old pics i posted before. you can see at the top of the air brush can there is a valve from which i can control the pressure.
http://img92.imageshack.us/img92/9513/propellantmodev7.th.jpg (http://img92.imageshack.us/my.php?image=propellantmodev7.jpg)

http://img293.imageshack.us/img293/2829/propellantmod3au0.th.jpg (http://img293.imageshack.us/my.php?image=propellantmod3au0.jpg)


http://img412.imageshack.us/img412/8986/propellantmod1zg4.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod1zg4.jpg)

http://inlinethumb59.webshots.com/1274/2732893440100511463S600x600Q85.jpg


I say thank you for your kindly observations and for the tips.

Really soon i´ll bring very nice updates as the air compressor system i am mounting is going just fine.

I did the lung screw cover system and tomorrow i´ll put the botton valve and finish the compressor for the airbrush works.

The cover with regulator screw mounting:http://img01.picoodle.com/img/img01/7/3/28/pedrotorresfilho/f_P3200003m_2d6bfa6.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/28/pedrotorresfilho/f_P3200003m_2d6bfa6.jpg)

Just a better shot of top alien (still miss 1 led)
http://img01.picoodle.com/img/img01/7/3/28/pedrotorresfilho/f_P3200011m_3e7dcc8.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/28/pedrotorresfilho/f_P3200011m_3e7dcc8.jpg)

Now i am going to bed, see you tomorrow !

Thanks,

Pedro Torres.

[pedrofilho]

i shouldn't say it works at that pressure but rather the tank i have hold that pressure then i regulate it as the can.

here are the old pics i posted before. you can see at the top of the air brush can there is a valve from which i can control the pressure.
http://img92.imageshack.us/img92/9513/propellantmodev7.th.jpg (http://img92.imageshack.us/my.php?image=propellantmodev7.jpg)

http://img293.imageshack.us/img293/2829/propellantmod3au0.th.jpg (http://img293.imageshack.us/my.php?image=propellantmod3au0.jpg)


http://img412.imageshack.us/img412/8986/propellantmod1zg4.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod1zg4.jpg)

http://inlinethumb59.webshots.com/1274/2732893440100511463S600x600Q85.jpg


I say thank you for your kindly observations and for the tips.

Really soon i´ll bring very nice updates as the air compressor system i am mounting is going just fine.

I did the lung screw cover system and tomorrow i´ll put the botton valve and finish the compressor for the airbrush works.

The cover with regulator screw mounting:http://img01.picoodle.com/img/img01/7/3/28/pedrotorresfilho/f_P3200003m_2d6bfa6.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/28/pedrotorresfilho/f_P3200003m_2d6bfa6.jpg)

Just a better shot of top alien (still miss 1 led)
http://img01.picoodle.com/img/img01/7/3/28/pedrotorresfilho/f_P3200011m_3e7dcc8.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/28/pedrotorresfilho/f_P3200011m_3e7dcc8.jpg)

Now i am going to bed, see you tomorrow !

Thanks,

Pedro Torres.

[pedrofilho]

i shouldn't say it works at that pressure but rather the tank i have hold that pressure then i regulate it as the can.

here are the old pics i posted before. you can see at the top of the air brush can there is a valve from which i can control the pressure.
http://img92.imageshack.us/img92/9513/propellantmodev7.th.jpg (http://img92.imageshack.us/my.php?image=propellantmodev7.jpg)

http://img293.imageshack.us/img293/2829/propellantmod3au0.th.jpg (http://img293.imageshack.us/my.php?image=propellantmod3au0.jpg)


http://img412.imageshack.us/img412/8986/propellantmod1zg4.th.jpg (http://img412.imageshack.us/my.php?image=propellantmod1zg4.jpg)

http://inlinethumb59.webshots.com/1274/2732893440100511463S600x600Q85.jpg


I say thank you for your kindly observations and for the tips.

Really soon i´ll bring very nice updates as the air compressor system i am mounting is going just fine.

I did the lung screw cover system and tomorrow i´ll put the botton valve and finish the compressor for the airbrush works.

The cover with regulator screw mounting:http://img01.picoodle.com/img/img01/7/3/28/pedrotorresfilho/f_P3200003m_2d6bfa6.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/28/pedrotorresfilho/f_P3200003m_2d6bfa6.jpg)

Just a better shot of top alien (still miss 1 led)
http://img01.picoodle.com/img/img01/7/3/28/pedrotorresfilho/f_P3200011m_3e7dcc8.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/28/pedrotorresfilho/f_P3200011m_3e7dcc8.jpg)

Now i am going to bed, see you tomorrow !

Thanks,

Pedro Torres.

[pedrofilho]

Look fantastic so far pedro.. Took me a while to read through the log, but I'm loving it so far!

-Jeremy


Thank you for ur kindly coment. This mod still will suffer too many changes ´till the end of the year, when i´ll subscribe it to WW coolermaster casemoding contest 2007.

I´ll do an wires work to put everything in order on this case, i am just waiting the money for a new font, because this one is already on it´s limit !

So, i did a functional air reservoir for the airbrush compressor and will start some paintings here. Keep you eyes opened:

Best regards,


Today i got the black cooldrive from CM RMA. Quite amazing service and pretty stuff the black unit, look at this:
http://img03.picoodle.com/img/img03/7/3/29/pedrotorresfilho/f_P3210001m_c3f8f5a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/29/pedrotorresfilho/f_P3210001m_c3f8f5a.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210005m_1ca85eb.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210005m_1ca85eb.jpg)

http://img03.picoodle.com/img/img03/7/3/29/pedrotorresfilho/f_P3210011m_c49a90d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/29/pedrotorresfilho/f_P3210011m_c49a90d.jpg)

See you,

Pedro Torres

[pedrofilho]

Look fantastic so far pedro.. Took me a while to read through the log, but I'm loving it so far!

-Jeremy


Thank you for ur kindly coment. This mod still will suffer too many changes ´till the end of the year, when i´ll subscribe it to WW coolermaster casemoding contest 2007.

I´ll do an wires work to put everything in order on this case, i am just waiting the money for a new font, because this one is already on it´s limit !

So, i did a functional air reservoir for the airbrush compressor and will start some paintings here. Keep you eyes opened:

Best regards,


Today i got the black cooldrive from CM RMA. Quite amazing service and pretty stuff the black unit, look at this:
http://img03.picoodle.com/img/img03/7/3/29/pedrotorresfilho/f_P3210001m_c3f8f5a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/29/pedrotorresfilho/f_P3210001m_c3f8f5a.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210005m_1ca85eb.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210005m_1ca85eb.jpg)

http://img03.picoodle.com/img/img03/7/3/29/pedrotorresfilho/f_P3210011m_c49a90d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/29/pedrotorresfilho/f_P3210011m_c49a90d.jpg)

See you,

Pedro Torres

[pedrofilho]

Look fantastic so far pedro.. Took me a while to read through the log, but I'm loving it so far!

-Jeremy


Thank you for ur kindly coment. This mod still will suffer too many changes ´till the end of the year, when i´ll subscribe it to WW coolermaster casemoding contest 2007.

I´ll do an wires work to put everything in order on this case, i am just waiting the money for a new font, because this one is already on it´s limit !

So, i did a functional air reservoir for the airbrush compressor and will start some paintings here. Keep you eyes opened:

Best regards,


Today i got the black cooldrive from CM RMA. Quite amazing service and pretty stuff the black unit, look at this:
http://img03.picoodle.com/img/img03/7/3/29/pedrotorresfilho/f_P3210001m_c3f8f5a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/29/pedrotorresfilho/f_P3210001m_c3f8f5a.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210005m_1ca85eb.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210005m_1ca85eb.jpg)

http://img03.picoodle.com/img/img03/7/3/29/pedrotorresfilho/f_P3210011m_c49a90d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/29/pedrotorresfilho/f_P3210011m_c49a90d.jpg)

See you,

Pedro Torres

[pedrofilho]

Look fantastic so far pedro.. Took me a while to read through the log, but I'm loving it so far!

-Jeremy


Thank you for ur kindly coment. This mod still will suffer too many changes ´till the end of the year, when i´ll subscribe it to WW coolermaster casemoding contest 2007.

I´ll do an wires work to put everything in order on this case, i am just waiting the money for a new font, because this one is already on it´s limit !

So, i did a functional air reservoir for the airbrush compressor and will start some paintings here. Keep you eyes opened:

Best regards,


Today i got the black cooldrive from CM RMA. Quite amazing service and pretty stuff the black unit, look at this:
http://img03.picoodle.com/img/img03/7/3/29/pedrotorresfilho/f_P3210001m_c3f8f5a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/29/pedrotorresfilho/f_P3210001m_c3f8f5a.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210005m_1ca85eb.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210005m_1ca85eb.jpg)

http://img03.picoodle.com/img/img03/7/3/29/pedrotorresfilho/f_P3210011m_c49a90d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/29/pedrotorresfilho/f_P3210011m_c49a90d.jpg)

See you,

Pedro Torres

[pedrofilho]

I´ve painted the cooldrive 6 and changed the vantec nexus front panel for a black on, so, everything get more harmonious and clean, take a look:

http://img03.picoodle.com/img/img03/7/3/29/pedrotorresfilho/f_P3210008m_afe0c27.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/29/pedrotorresfilho/f_P3210008m_afe0c27.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210009m_aeb6e09.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210009m_aeb6e09.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210015m_5af96e0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210015m_5af96e0.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210016m_1107754.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210016m_1107754.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210001m_a39afc0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210001m_a39afc0.jpg)
http://img03.picoodle.com/img/img03/7/3/29/pedrotorresfilho/f_P32100122m_d11f2cf.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/29/pedrotorresfilho/f_P32100122m_d11f2cf.jpg)

See you,

Pedro Torres.

[pedrofilho]

I´ve painted the cooldrive 6 and changed the vantec nexus front panel for a black on, so, everything get more harmonious and clean, take a look:

http://img03.picoodle.com/img/img03/7/3/29/pedrotorresfilho/f_P3210008m_afe0c27.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/29/pedrotorresfilho/f_P3210008m_afe0c27.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210009m_aeb6e09.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210009m_aeb6e09.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210015m_5af96e0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210015m_5af96e0.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210016m_1107754.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210016m_1107754.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210001m_a39afc0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210001m_a39afc0.jpg)
http://img03.picoodle.com/img/img03/7/3/29/pedrotorresfilho/f_P32100122m_d11f2cf.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/29/pedrotorresfilho/f_P32100122m_d11f2cf.jpg)

See you,

Pedro Torres.

[pedrofilho]

I´ve painted the cooldrive 6 and changed the vantec nexus front panel for a black on, so, everything get more harmonious and clean, take a look:

http://img03.picoodle.com/img/img03/7/3/29/pedrotorresfilho/f_P3210008m_afe0c27.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/29/pedrotorresfilho/f_P3210008m_afe0c27.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210009m_aeb6e09.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210009m_aeb6e09.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210015m_5af96e0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210015m_5af96e0.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210016m_1107754.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210016m_1107754.jpg)

http://img01.picoodle.com/img/img01/7/3/29/pedrotorresfilho/f_P3210001m_a39afc0.jpg (http://www.picoodle.com/view.php?srv=img01&img=/7/3/29/pedrotorresfilho/f_P3210001m_a39afc0.jpg)
http://img03.picoodle.com/img/img03/7/3/29/pedrotorresfilho/f_P32100122m_d11f2cf.jpg (http://www.picoodle.com/view.php?srv=img03&img=/7/3/29/pedrotorresfilho/f_P32100122m_d11f2cf.jpg)

See you,

Pedro Torres.

[pedrofilho]

Looking cool man, I love how you mod everything that goes in there.

Dear jdbnsn,

You´re aways supporting us, what is the best reward we can expect.


Thank you !

I´ve ordered some hot stuff and i´m 'till buying some materials to the next steps at this time, so, wait for really nice updates soon.

Pedro Torres.

[pedrofilho]

Looking cool man, I love how you mod everything that goes in there.

Dear jdbnsn,

You´re aways supporting us, what is the best reward we can expect.


Thank you !

I´ve ordered some hot stuff and i´m 'till buying some materials to the next steps at this time, so, wait for really nice updates soon.

Pedro Torres.

[pedrofilho]

Just joined the forum after seeing your detailed work log.
Can't wait to see the finished product. I have allot of reading to do before I attempt any case mod that would even compare to what you have in the works.

Looks Great! :up:

Thank you -eck, your opinion is very important to me. Keep watching, I´ll be back soon with really big news.

I´m planning to do a paint job, textures and plexi work on the next week beginning.

Glad you registered to do your first post here.

Be wellcome,

Pedro Torres.

[pedrofilho]

Just joined the forum after seeing your detailed work log.
Can't wait to see the finished product. I have allot of reading to do before I attempt any case mod that would even compare to what you have in the works.

Looks Great! :up:

Thank you -eck, your opinion is very important to me. Keep watching, I´ll be back soon with really big news.

I´m planning to do a paint job, textures and plexi work on the next week beginning.

Glad you registered to do your first post here.

Be wellcome,

Pedro Torres.

[pedrofilho]

13.04.2007

Some materiais to the next big update and painting of Cooler Master 6::
http://img03.picoodle.com/img/img03/8/4/14/pedrotorresfilho/f_P4050001m_6bcf09f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/14/pedrotorresfilho/f_P4050001m_6bcf09f.jpg)

http://img02.picoodle.com/img/img02/8/4/14/pedrotorresfilho/f_P4050005m_9ed1b6f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/14/pedrotorresfilho/f_P4050005m_9ed1b6f.jpg)

http://img03.picoodle.com/img/img03/8/4/14/pedrotorresfilho/f_P4050008m_ca84601.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/14/pedrotorresfilho/f_P4050008m_ca84601.jpg)

A few amount of leds
http://img02.picoodle.com/img/img02/8/4/14/pedrotorresfilho/f_P4050011m_1b38a5e.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/14/pedrotorresfilho/f_P4050011m_1b38a5e.jpg)

http://img02.picoodle.com/img/img02/8/4/14/pedrotorresfilho/f_P4050014m_f2ba509.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/14/pedrotorresfilho/f_P4050014m_f2ba509.jpg)

Cooler Master Musketeer 3
http://img03.picoodle.com/img/img03/8/4/14/pedrotorresfilho/f_P4050016m_9406a7b.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/14/pedrotorresfilho/f_P4050016m_9406a7b.jpg)

http://img02.picoodle.com/img/img02/8/4/14/pedrotorresfilho/f_P4050020m_0cc5f6b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/14/pedrotorresfilho/f_P4050020m_0cc5f6b.jpg)

Enermax Liberty 620 font

http://img03.picoodle.com/img/img03/8/4/14/pedrotorresfilho/f_P4050023m_1430d50.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/14/pedrotorresfilho/f_P4050023m_1430d50.jpg)

Body filler for some textures
http://img03.picoodle.com/img/img03/8/4/14/pedrotorresfilho/f_P4050024m_c85668d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/14/pedrotorresfilho/f_P4050024m_c85668d.jpg)

[pedrofilho]

13.04.2007

Some materiais to the next big update and painting of Cooler Master 6::
http://img03.picoodle.com/img/img03/8/4/14/pedrotorresfilho/f_P4050001m_6bcf09f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/14/pedrotorresfilho/f_P4050001m_6bcf09f.jpg)

http://img02.picoodle.com/img/img02/8/4/14/pedrotorresfilho/f_P4050005m_9ed1b6f.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/14/pedrotorresfilho/f_P4050005m_9ed1b6f.jpg)

http://img03.picoodle.com/img/img03/8/4/14/pedrotorresfilho/f_P4050008m_ca84601.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/14/pedrotorresfilho/f_P4050008m_ca84601.jpg)

A few amount of leds
http://img02.picoodle.com/img/img02/8/4/14/pedrotorresfilho/f_P4050011m_1b38a5e.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/14/pedrotorresfilho/f_P4050011m_1b38a5e.jpg)

http://img02.picoodle.com/img/img02/8/4/14/pedrotorresfilho/f_P4050014m_f2ba509.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/14/pedrotorresfilho/f_P4050014m_f2ba509.jpg)

Cooler Master Musketeer 3
http://img03.picoodle.com/img/img03/8/4/14/pedrotorresfilho/f_P4050016m_9406a7b.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/14/pedrotorresfilho/f_P4050016m_9406a7b.jpg)

http://img02.picoodle.com/img/img02/8/4/14/pedrotorresfilho/f_P4050020m_0cc5f6b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/14/pedrotorresfilho/f_P4050020m_0cc5f6b.jpg)

Enermax Liberty 620 font

http://img03.picoodle.com/img/img03/8/4/14/pedrotorresfilho/f_P4050023m_1430d50.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/14/pedrotorresfilho/f_P4050023m_1430d50.jpg)

Body filler for some textures
http://img03.picoodle.com/img/img03/8/4/14/pedrotorresfilho/f_P4050024m_c85668d.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/14/pedrotorresfilho/f_P4050024m_c85668d.jpg)

[pedrofilho]

Got this 2 pieces of cristal plexi to remake the 3D ET face from side panel, because the other UV reactive was stollen all colors from inside:
http://img02.picoodle.com/img/img02/8/4/15/pedrotorresfilho/f_P4070003m_81d64b8.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/15/pedrotorresfilho/f_P4070003m_81d64b8.jpg)

Another new: i resized all the pics to pages load faster.

See you !

Pedro Torres.

[pedrofilho]

Are you going to sand or paint the grey on the sides.. ?

Yes. I´ll paint it like alien metal. Also, i´ll do some texturing yet, on both sides of the case. Until the end of month i´ll unmount the case to do this.

Thank you for your visit !

Pedro Torres.

[pedrofilho]

all i can say is some very very innovative ideas going on.

i love the front mounted Res.
also thanks for the idea with the Can (+rep) i will probably adapt this at some point

great work cant wait to see what it looks like with some wire management

Thank you ! Wire manaement will be the next step, also, i´ll finish the alien reservoir. It will be like an alien regeneration chamber.


HEY! that was my idea! but he was gonna do it anyway so it doesn't matter

yes i like all the new stuff you got for it

You have the idea, but, i dit it first?! Luck on your fabrication...

Glad i´ve inspirated you for doing the same and, yeah, there is a lot of cool stuff on the case, and more are coming..

Thanks for your coment !


so it was!
+rep also

Thank you for you coment !

By the end of the month i´ll unmount everything to do some changes on this project, and improve some things.

See you !

Pedro Torres.

[pedrofilho]

24.04.2007

Some cool stuff I’ve just received:
http://img02.picoodle.com/img/img02/8/4/24/pedrotorresfilho/f_P4160025m_75b342b.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/24/pedrotorresfilho/f_P4160025m_75b342b.jpg)

A new easy grip molex kit:
http://img03.picoodle.com/img/img03/8/4/24/pedrotorresfilho/f_P4100007m_5bed6f0.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/24/pedrotorresfilho/f_P4100007m_5bed6f0.jpg)

Cooler Master UV Silent Fans from Sponsor:
http://img03.picoodle.com/img/img03/8/4/24/pedrotorresfilho/f_P4160013m_85e3fac.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/24/pedrotorresfilho/f_P4160013m_85e3fac.jpg)

VGA memories low profile heatsinks:
http://img03.picoodle.com/img/img03/8/4/24/pedrotorresfilho/f_P4160015m_92ec3ee.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/24/pedrotorresfilho/f_P4160015m_92ec3ee.jpg)

This cooler is really beautiful, a nice addiction to de side panel:
http://img02.picoodle.com/img/img02/8/4/24/pedrotorresfilho/f_P4160017m_e5f37a6.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/24/pedrotorresfilho/f_P4160017m_e5f37a6.jpg)

Wires and connectors for a decent wire management:
http://img02.picoodle.com/img/img02/8/4/24/pedrotorresfilho/f_P4160023m_237e8b3.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/24/pedrotorresfilho/f_P4160023m_237e8b3.jpg)

A little bit of work… Redoing the front panel of cooldrive 6 I’ve destroyed.
http://img02.picoodle.com/img/img02/8/4/24/pedrotorresfilho/f_P4160008m_859a396.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/24/pedrotorresfilho/f_P4160008m_859a396.jpg)

http://img03.picoodle.com/img/img03/8/4/24/pedrotorresfilho/f_P4160009m_4cab1e7.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/24/pedrotorresfilho/f_P4160009m_4cab1e7.jpg)

After some sanding…
http://img02.picoodle.com/img/img02/8/4/24/pedrotorresfilho/f_P4160010m_d9f1be5.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/24/pedrotorresfilho/f_P4160010m_d9f1be5.jpg)

Fits perfectly:
http://img03.picoodle.com/img/img03/8/4/24/pedrotorresfilho/f_P4160011m_9db3a5f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/24/pedrotorresfilho/f_P4160011m_9db3a5f.jpg)

The rest of updates will comes, maybe, in may.

Thanks,

Pedro Torres.

[pedrofilho]

Cooldrive6 mod completed:

http://img03.picoodle.com/img/img03/8/4/25/pedrotorresfilho/f_P4170001m_adf13a1.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/25/pedrotorresfilho/f_P4170001m_adf13a1.jpg)


http://img03.picoodle.com/img/img03/8/4/25/pedrotorresfilho/f_P4170004m_e5fb015.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/25/pedrotorresfilho/f_P4170004m_e5fb015.jpg)

Starting the side panel conclusion:
http://img03.picoodle.com/img/img03/8/4/25/pedrotorresfilho/f_P4170002m_024258b.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/25/pedrotorresfilho/f_P4170002m_024258b.jpg)

That´s all folks !

Pedro Torres.

[pedrofilho]

Unpacking the Cooler Master Dual Storm cooler to study it’s adaptation to the side panel hole:
http://img02.picoodle.com/img/img02/8/4/29/pedrotorresfilho/f_P4180012m_e2b7485.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/29/pedrotorresfilho/f_P4180012m_e2b7485.jpg)

http://img02.picoodle.com/img/img02/8/4/29/pedrotorresfilho/f_P4180015m_fe77a60.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/29/pedrotorresfilho/f_P4180015m_fe77a60.jpg)

http://img01.picoodle.com/img/img01/8/4/29/pedrotorresfilho/f_P4180016m_c044472.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/4/29/pedrotorresfilho/f_P4180016m_c044472.jpg)

http://img02.picoodle.com/img/img02/8/4/29/pedrotorresfilho/f_P4180020m_c6c1d36.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/29/pedrotorresfilho/f_P4180020m_c6c1d36.jpg)

The beauty revealed:
http://img03.picoodle.com/img/img03/8/4/29/pedrotorresfilho/f_P4180017m_5f9019f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/29/pedrotorresfilho/f_P4180017m_5f9019f.jpg)

Final remake of 3D type ET face on crystal plexi-glass:
http://img01.picoodle.com/img/img01/8/4/29/pedrotorresfilho/f_P4180021m_e73ecb3.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/4/29/pedrotorresfilho/f_P4180021m_e73ecb3.jpg)

http://img03.picoodle.com/img/img03/8/4/29/pedrotorresfilho/f_P4180023m_0f8f704.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/29/pedrotorresfilho/f_P4180023m_0f8f704.jpg)

http://img03.picoodle.com/img/img03/8/4/29/pedrotorresfilho/f_P4180024m_5a248b9.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/29/pedrotorresfilho/f_P4180024m_5a248b9.jpg)

http://img02.picoodle.com/img/img02/8/4/29/pedrotorresfilho/f_P4180025m_d3742ae.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/29/pedrotorresfilho/f_P4180025m_d3742ae.jpg)

http://img02.picoodle.com/img/img02/8/4/29/pedrotorresfilho/f_P4180026m_6e788ef.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/4/29/pedrotorresfilho/f_P4180026m_6e788ef.jpg)

Again (stone age method):
http://img01.picoodle.com/img/img01/8/4/29/pedrotorresfilho/f_P4190027m_159f9de.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/4/29/pedrotorresfilho/f_P4190027m_159f9de.jpg)

Done:
http://img01.picoodle.com/img/img01/8/4/29/pedrotorresfilho/f_P4200030m_436773f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/4/29/pedrotorresfilho/f_P4200030m_436773f.jpg)

Photography is a second hobby of mine, so, this is the tripod I’ll use to take pictures for the contest (mostly night shots blurry without it):
http://img03.picoodle.com/img/img03/8/4/29/pedrotorresfilho/f_P4200031m_9c443e3.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/4/29/pedrotorresfilho/f_P4200031m_9c443e3.jpg)

Thanks for visiting. !

Pedro Torres.

[pedrofilho]

The side panel texture begins:
http://img03.picoodle.com/img/img03/8/5/9/pedrotorresfilho/f_P4280003m_4642e0a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/9/pedrotorresfilho/f_P4280003m_4642e0a.jpg)

Epoxi:
http://img02.picoodle.com/img/img02/8/5/9/pedrotorresfilho/f_P4300005m_f433db7.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/9/pedrotorresfilho/f_P4300005m_f433db7.jpg)

Blondo on borders:
http://img02.picoodle.com/img/img02/8/5/9/pedrotorresfilho/f_P5010001m_740c331.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/9/pedrotorresfilho/f_P5010001m_740c331.jpg)

I am waiting the plastic mass dry to finish it sanding and painting.

See you later with the results !

Pedro Torres.

[pedrofilho]

The side panel finished, waiting for a paint job:
http://img02.picoodle.com/img/img02/8/5/9/pedrotorresfilho/f_P5010002m_c18e05a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/9/pedrotorresfilho/f_P5010002m_c18e05a.jpg)

The camouflage of analog thermometer (invented metod):
http://img02.picoodle.com/img/img02/8/5/9/pedrotorresfilho/f_P5010003m_7a83a6d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/9/pedrotorresfilho/f_P5010003m_7a83a6d.jpg)

Second adhesive tape to be easily removed after texture works:
http://img02.picoodle.com/img/img02/8/5/9/pedrotorresfilho/f_P5010006m_a6a7991.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/9/pedrotorresfilho/f_P5010006m_a6a7991.jpg)

Voilà:
http://img03.picoodle.com/img/img03/8/5/9/pedrotorresfilho/f_P5010007m_fa6fcee.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/9/pedrotorresfilho/f_P5010007m_fa6fcee.jpg)

Perfect fit:
http://img03.picoodle.com/img/img03/8/5/9/pedrotorresfilho/f_P5010008m_e4d2401.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/9/pedrotorresfilho/f_P5010008m_e4d2401.jpg)

Drying for paintings:
http://img01.picoodle.com/img/img01/8/5/9/pedrotorresfilho/f_P5010009m_364ed20.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/9/pedrotorresfilho/f_P5010009m_364ed20.jpg)

See you later with more results:

Pedro Torres.

[pedrofilho]

Ready for paintings:
http://img01.picoodle.com/img/img01/8/5/9/pedrotorresfilho/f_P5010004m_dd097da.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/9/pedrotorresfilho/f_P5010004m_dd097da.jpg)

Fist hand, Polished Aluminum:
http://img02.picoodle.com/img/img02/8/5/9/pedrotorresfilho/f_P5010007m_2706b06.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/9/pedrotorresfilho/f_P5010007m_2706b06.jpg)

See you later with more pics !

Pedro Torres.

[Spacehonkey]

http://img01.picoodle.com/img/img01/8/5/9/pedrotorresfilho/f_P5010004m_dd097da.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/9/pedrotorresfilho/f_P5010004m_dd097da.jpg)


Forget the mod who's the girl in the newspaper article?

Just kidding, I like what you've done so far.

[pedrofilho]

Forget the mod who's the girl in the newspaper article?

Just kidding, I like what you've done so far.

The girl in the photo is the winner of a reality show called ´Big Brother Brasil´. She´s pretty nice.

Thanks for coment, the job is calling me.


I second that about the newspaper article, I totally need to visit Brazil! I love that side panel by the way, great shaping work Pedro!

Thank you jdbnsn, the shape gets fine this time and now i´m working on the texture of side panel. Need some material i hope to buy today.

When you come to Brazil let me know and i introduce some pretty babies here. :D

See you later !

Pedro Torres.

[pedrofilho]

Side panel textures (with PVC):
http://img03.picoodle.com/img/img03/8/5/10/pedrotorresfilho/f_P5020010m_d3b4a30.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/10/pedrotorresfilho/f_P5020010m_d3b4a30.jpg)

http://img03.picoodle.com/img/img03/8/5/10/pedrotorresfilho/f_P5020013m_4f779b6.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/10/pedrotorresfilho/f_P5020013m_4f779b6.jpg)

http://img02.picoodle.com/img/img02/8/5/10/pedrotorresfilho/f_P5020017m_d61cdf2.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/10/pedrotorresfilho/f_P5020017m_d61cdf2.jpg)

Work done, after that, comes the paint:
http://img03.picoodle.com/img/img03/8/5/10/pedrotorresfilho/f_P5020018m_00c8ab4.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/10/pedrotorresfilho/f_P5020018m_00c8ab4.jpg)

See you tomorrow with nice news!

Pedro Torres.

[pedrofilho]

Some goodies I’ve gotten today:
The Cooler Master Hyper 6+ and the COOLLABORATORY-LP Thermal compound:
http://img03.picoodle.com/img/img03/8/5/11/pedrotorresfilho/f_P5030001m_2770114.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/11/pedrotorresfilho/f_P5030001m_2770114.jpg)

2 pairs of 4” UV CC and some Logitech G5 mouses to keep economy up:
http://img02.picoodle.com/img/img02/8/5/11/pedrotorresfilho/f_P5030003m_ea97ae2.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/11/pedrotorresfilho/f_P5030003m_ea97ae2.jpg)

A closer view of the COOLLABORATORY-LP Thermal compound
http://img03.picoodle.com/img/img03/8/5/11/pedrotorresfilho/f_P5030006m_f7269eb.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/11/pedrotorresfilho/f_P5030006m_f7269eb.jpg)

The new Enermax Liberty 620 font (all cables sleeved blue UV):
http://img02.picoodle.com/img/img02/8/5/11/pedrotorresfilho/f_P5030007m_9085b3d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/11/pedrotorresfilho/f_P5030007m_9085b3d.jpg)

The 4” UV CC which will illuminate the front panel ET:
http://img02.picoodle.com/img/img02/8/5/11/pedrotorresfilho/f_P5030008m_7ad3978.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/11/pedrotorresfilho/f_P5030008m_7ad3978.jpg)

That’s it for now, see you later !

Pedro Torres.

[pedrofilho]

well, no its not the same one but its almost the same, my worklog is on a german site heres the link http://www.moddingtech.de/cgi-bin/mtiB/ikonboard.cgi?;act=ST;f=15;t=10931
dont be arfaid its german^^
and here s the case i used
http://www.kuchenstueck.de/pe3466444.jpg
as you can see almost the same^^

It's almost the same, really.

Thank's for the link. I saw your mod worklog. Nice work.

Pedro Torres.

[pedrofilho]

The front panel remake process:

http://img02.picoodle.com/img/img02/8/5/16/pedrotorresfilho/f_P5080002m_2258b7d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/16/pedrotorresfilho/f_P5080002m_2258b7d.jpg)

First cut:
http://img02.picoodle.com/img/img02/8/5/16/pedrotorresfilho/f_P5080003m_98fee87.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/16/pedrotorresfilho/f_P5080003m_98fee87.jpg)

The bit for the left border:
http://img03.picoodle.com/img/img03/8/5/16/pedrotorresfilho/f_P5080004m_65850c2.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/16/pedrotorresfilho/f_P5080004m_65850c2.jpg)

First pass:
http://img03.picoodle.com/img/img03/8/5/16/pedrotorresfilho/f_P5080006m_884c5d0.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/16/pedrotorresfilho/f_P5080006m_884c5d0.jpg)

Both sides:
http://img03.picoodle.com/img/img03/8/5/16/pedrotorresfilho/f_P5080007m_3151d99.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/16/pedrotorresfilho/f_P5080007m_3151d99.jpg)

The bit for the bending mark:
http://img03.picoodle.com/img/img03/8/5/16/pedrotorresfilho/f_P5080008m_ef644bb.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/16/pedrotorresfilho/f_P5080008m_ef644bb.jpg)

The bend mark done:
http://img02.picoodle.com/img/img02/8/5/16/pedrotorresfilho/f_P5080009m_ef18795.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/16/pedrotorresfilho/f_P5080009m_ef18795.jpg)

Ready for bending I’ll start next weekend:
http://img02.picoodle.com/img/img02/8/5/16/pedrotorresfilho/f_P5080010m_b0167b3.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/16/pedrotorresfilho/f_P5080010m_b0167b3.jpg)

See you !

Pedro Torres.

[pedrofilho]

The opposite side panel concept (UFO):
http://img03.picoodle.com/img/img03/8/5/19/pedrotorresfilho/f_P5110003m_b34e8c3.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/19/pedrotorresfilho/f_P5110003m_b34e8c3.jpg)

See you soon !

Pedro Torres.

[pedrofilho]

Working on the feet and opposite side panel UFO cup
http://img03.picoodle.com/img/img03/8/5/21/pedrotorresfilho/f_P5120001m_1ba3af3.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/21/pedrotorresfilho/f_P5120001m_1ba3af3.jpg)

http://img02.picoodle.com/img/img02/8/5/21/pedrotorresfilho/f_P5120003m_30018d3.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/21/pedrotorresfilho/f_P5120003m_30018d3.jpg)

http://img02.picoodle.com/img/img02/8/5/21/pedrotorresfilho/f_P5120004m_22604eb.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/21/pedrotorresfilho/f_P5120004m_22604eb.jpg)

Ready for a paint job:
http://img03.picoodle.com/img/img03/8/5/21/pedrotorresfilho/f_P5130005m_c6ffa95.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/21/pedrotorresfilho/f_P5130005m_c6ffa95.jpg)

Chrome for a better shine:
http://img03.picoodle.com/img/img03/8/5/21/pedrotorresfilho/f_P5130007m_b9a42ee.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/21/pedrotorresfilho/f_P5130007m_b9a42ee.jpg)

That’s all for now.

See you !

Pedro Torres.

[pedrofilho]

Feet base remake
http://img03.picoodle.com/img/img03/8/5/21/pedrotorresfilho/f_P5130002m_b64c356.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/21/pedrotorresfilho/f_P5130002m_b64c356.jpg)

Spaceship construction:

Dremel router with circle cutter adapter
http://img03.picoodle.com/img/img03/8/5/21/pedrotorresfilho/f_P5130004m_74d31a1.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/21/pedrotorresfilho/f_P5130004m_74d31a1.jpg)

http://img02.picoodle.com/img/img02/8/5/21/pedrotorresfilho/f_P5130005m_831916a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/21/pedrotorresfilho/f_P5130005m_831916a.jpg)

Marking the center:
http://img03.picoodle.com/img/img03/8/5/21/pedrotorresfilho/f_P5130007m_b287e6e.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/21/pedrotorresfilho/f_P5130007m_b287e6e.jpg)

Marking the cut circle:
http://img02.picoodle.com/img/img02/8/5/21/pedrotorresfilho/f_P5130011m_429a9cf.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/21/pedrotorresfilho/f_P5130011m_429a9cf.jpg)

The right tool to do a small circle cut:
http://img02.picoodle.com/img/img02/8/5/21/pedrotorresfilho/f_P5130012m_c4dc5df.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/21/pedrotorresfilho/f_P5130012m_c4dc5df.jpg)

The result:
http://img02.picoodle.com/img/img02/8/5/21/pedrotorresfilho/f_P5130014m_fb10568.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/21/pedrotorresfilho/f_P5130014m_fb10568.jpg)

See you soon !

Pedro Torres.

[pedrofilho]

Spacecraft dome holes done:

http://img03.picoodle.com/img/img03/8/5/21/pedrotorresfilho/f_P5130004m_976ed2f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/21/pedrotorresfilho/f_P5130004m_976ed2f.jpg)

See you tomorrow !

Pedro Torres.

[pedrofilho]

Spacecraft building:
The materials:
http://img03.picoodle.com/img/img03/8/5/22/pedrotorresfilho/f_P5140002m_7eadc95.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/22/pedrotorresfilho/f_P5140002m_7eadc95.jpg)

http://img02.picoodle.com/img/img02/8/5/22/pedrotorresfilho/f_P5140003m_2b911d1.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/22/pedrotorresfilho/f_P5140003m_2b911d1.jpg)

Marks
http://img02.picoodle.com/img/img02/8/5/22/pedrotorresfilho/f_P5140006m_a247cec.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/22/pedrotorresfilho/f_P5140006m_a247cec.jpg)

Feet base sanding with Dremel:
http://img02.picoodle.com/img/img02/8/5/22/pedrotorresfilho/f_P5140011m_0fbe043.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/22/pedrotorresfilho/f_P5140011m_0fbe043.jpg)

Work done:
http://img03.picoodle.com/img/img03/8/5/22/pedrotorresfilho/f_P5140014m_dd71cdd.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/22/pedrotorresfilho/f_P5140014m_dd71cdd.jpg)

The circle scratch:
http://img03.picoodle.com/img/img03/8/5/22/pedrotorresfilho/f_P5140015m_ffc941c.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/22/pedrotorresfilho/f_P5140015m_ffc941c.jpg)

The center base fixed with super-glue:
http://img02.picoodle.com/img/img02/8/5/22/pedrotorresfilho/f_P5140016m_7ca3256.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/22/pedrotorresfilho/f_P5140016m_7ca3256.jpg)

The leds work:
http://img03.picoodle.com/img/img03/8/5/22/pedrotorresfilho/f_P5140017m_ca4efd9.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/22/pedrotorresfilho/f_P5140017m_ca4efd9.jpg)

http://img02.picoodle.com/img/img02/8/5/22/pedrotorresfilho/f_P5140018m_1bdca44.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/22/pedrotorresfilho/f_P5140018m_1bdca44.jpg)

http://img01.picoodle.com/img/img01/8/5/22/pedrotorresfilho/f_P5140021m_e1b3b3f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/22/pedrotorresfilho/f_P5140021m_e1b3b3f.jpg)

Fixing the leds on spacecraft dome:
http://img03.picoodle.com/img/img03/8/5/22/pedrotorresfilho/f_P5140023m_4fadd90.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/22/pedrotorresfilho/f_P5140023m_4fadd90.jpg)

Leds Fixed:
http://img03.picoodle.com/img/img03/8/5/22/pedrotorresfilho/f_P5140026m_7b91034.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/22/pedrotorresfilho/f_P5140026m_7b91034.jpg)

http://img02.picoodle.com/img/img02/8/5/22/pedrotorresfilho/f_P5140027m_d2aebd5.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/22/pedrotorresfilho/f_P5140027m_d2aebd5.jpg)

Wired:
http://img03.picoodle.com/img/img03/8/5/22/pedrotorresfilho/f_P5140029m_22ad0a7.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/22/pedrotorresfilho/f_P5140029m_22ad0a7.jpg)

The spacecraft dome placed on the center base:
http://img02.picoodle.com/img/img02/8/5/22/pedrotorresfilho/f_P5140031m_2e808bb.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/22/pedrotorresfilho/f_P5140031m_2e808bb.jpg)

The spacecraft body fixed with epoxy (2h to dry):
http://img03.picoodle.com/img/img03/8/5/22/pedrotorresfilho/f_P5140033m_4aba1a9.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/22/pedrotorresfilho/f_P5140033m_4aba1a9.jpg)

I’ll be back soon !

Thanks

Pedro Torres.

[pedrofilho]

The very, very, first UFO preview:
http://img03.picoodle.com/img/img03/8/5/22/pedrotorresfilho/f_P5150001m_ed8b85a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/22/pedrotorresfilho/f_P5150001m_ed8b85a.jpg)

See you later !

Pedro Torres.

[pedrofilho]

More about the UFO and top alien base:
http://img02.picoodle.com/img/img02/8/5/23/pedrotorresfilho/f_P5150001m_f724f29.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/23/pedrotorresfilho/f_P5150001m_f724f29.jpg)

http://img01.picoodle.com/img/img01/8/5/23/pedrotorresfilho/f_P5150002m_9afab8e.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/23/pedrotorresfilho/f_P5150002m_9afab8e.jpg)

Top alien base remake:
http://img02.picoodle.com/img/img02/8/5/23/pedrotorresfilho/f_P5150004m_7242c61.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/23/pedrotorresfilho/f_P5150004m_7242c61.jpg)

http://img02.picoodle.com/img/img02/8/5/23/pedrotorresfilho/f_P5150005m_0a3a80d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/23/pedrotorresfilho/f_P5150005m_0a3a80d.jpg)

Done:
http://img03.picoodle.com/img/img03/8/5/23/pedrotorresfilho/f_P5150006m_b3eb037.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/23/pedrotorresfilho/f_P5150006m_b3eb037.jpg)

See you later !

Pedro Torres

[pedrofilho]

Are those rocks being used as weights to hold the base of the UFO down or are they going to become part of the mod itself?

It's only to keep the base of the UFO down, nothing else. I think this UFO have not enought power to carry those rocks :D

Last but one gluing
http://img03.picoodle.com/img/img03/8/5/23/pedrotorresfilho/f_P5150001m_5708c3f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/23/pedrotorresfilho/f_P5150001m_5708c3f.jpg)

Next one will occur about 21:00h.

See you there.

Pedro Torres.

[pedrofilho]

This is what happens when use the wrong material:
http://img02.picoodle.com/img/img02/8/5/24/pedrotorresfilho/f_P5160001m_284218a.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/24/pedrotorresfilho/f_P5160001m_284218a.jpg)

Now, the work is going faster as a rabbit:
http://img01.picoodle.com/img/img01/8/5/24/pedrotorresfilho/f_P5160002m_282eec4.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/24/pedrotorresfilho/f_P5160002m_282eec4.jpg)

Taped:
http://img02.picoodle.com/img/img02/8/5/24/pedrotorresfilho/f_P5160006m_5031928.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/24/pedrotorresfilho/f_P5160006m_5031928.jpg)

Why don’t I think this before? I waste two days trying to get that PVC circle to shape I want…

See you really soon !

Pedro Torres.

[pedrofilho]

UFO dome protected:
http://img02.picoodle.com/img/img02/8/5/24/pedrotorresfilho/f_P5160002m_e4775cc.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/24/pedrotorresfilho/f_P5160002m_e4775cc.jpg)

Body filler first pass:
http://img03.picoodle.com/img/img03/8/5/24/pedrotorresfilho/f_P5160003m_a65981a.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/24/pedrotorresfilho/f_P5160003m_a65981a.jpg)

Second layer:
http://img01.picoodle.com/img/img01/8/5/24/pedrotorresfilho/f_P5160004m_67f25d9.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/24/pedrotorresfilho/f_P5160004m_67f25d9.jpg)

I’ll do one last body filler layer and sand it.

See you soon !

Pedro Torres.

[pedrofilho]

UFO 3rd shot.



Epoxy gluing

http://img02.picoodle.com/img/img02/8/5/25/pedrotorresfilho/f_P5160003m_17906c0.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/25/pedrotorresfilho/f_P5160003m_17906c0.jpg)



Glued:

http://img02.picoodle.com/img/img02/8/5/25/pedrotorresfilho/f_P5170005m_6067c97.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/25/pedrotorresfilho/f_P5170005m_6067c97.jpg)



More leds work:

http://img02.picoodle.com/img/img02/8/5/25/pedrotorresfilho/f_P5170007m_028691d.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/25/pedrotorresfilho/f_P5170007m_028691d.jpg)



A closer look:

http://img03.picoodle.com/img/img03/8/5/25/pedrotorresfilho/f_P5170010m_21225ab.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/25/pedrotorresfilho/f_P5170010m_21225ab.jpg)



Finished:

http://img02.picoodle.com/img/img02/8/5/25/pedrotorresfilho/f_P5170014m_20a3d6c.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/25/pedrotorresfilho/f_P5170014m_20a3d6c.jpg)



Making the borders clear:

http://img03.picoodle.com/img/img03/8/5/25/pedrotorresfilho/f_P5170015m_8cb70d5.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/25/pedrotorresfilho/f_P5170015m_8cb70d5.jpg)



A little dusty:

http://img01.picoodle.com/img/img01/8/5/25/pedrotorresfilho/f_P5170016m_f1baac9.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/25/pedrotorresfilho/f_P5170016m_f1baac9.jpg)



Ready for the leds:

http://img03.picoodle.com/img/img03/8/5/25/pedrotorresfilho/f_P5170017m_e8a26eb.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/25/pedrotorresfilho/f_P5170017m_e8a26eb.jpg)



Leds fixed:

http://img02.picoodle.com/img/img02/8/5/25/pedrotorresfilho/f_P5180020m_c10a525.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/25/pedrotorresfilho/f_P5180020m_c10a525.jpg)



In the dark, daylight !

http://img01.picoodle.com/img/img01/8/5/25/pedrotorresfilho/f_P5180021m_dc17e20.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/25/pedrotorresfilho/f_P5180021m_dc17e20.jpg)



Tomorrow I’ll work with the body filler again and finish the UFO.



Enjoy !



Pedro Torres.

[pedrofilho]

I'm speechless.

I'm also going to incorporate that idea with the LEDs into a mod of my own. Thanks for the inspiration, as always!

:up: :up: :up: :up: :up:

Glad to see that my work has inspirated someone.

Thanks for the coment !



Awesome! Like the ship from ET.

:D Thank you for the coment The Black Pumpkin, nice to see you.

Body filler work:
http://img02.picoodle.com/img/img02/8/5/27/pedrotorresfilho/f_P5180002m_50d4e0c.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/27/pedrotorresfilho/f_P5180002m_50d4e0c.jpg)

http://img02.picoodle.com/img/img02/8/5/27/pedrotorresfilho/f_P5180003m_b575380.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/27/pedrotorresfilho/f_P5180003m_b575380.jpg)

http://img02.picoodle.com/img/img02/8/5/27/pedrotorresfilho/f_P5180004m_0793eab.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/27/pedrotorresfilho/f_P5180004m_0793eab.jpg)

Today I’ll sand it before apply another body filler layer and do the texturing job.

See you soon !

Pedro Torres.

[pedrofilho]

After a hand sanding, the imperfections appears:
http://img01.picoodle.com/img/img01/8/5/28/pedrotorresfilho/f_P5200001m_df1da83.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/28/pedrotorresfilho/f_P5200001m_df1da83.jpg)

I’ll do another body filler layer and sand it again. Almost there.

See you later !

Pedro Torres.

[pedrofilho]

Painting the side panels:
http://img01.picoodle.com/img/img01/8/5/30/pedrotorresfilho/f_P5220002m_9b25b7f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/30/pedrotorresfilho/f_P5220002m_9b25b7f.jpg)

http://img02.picoodle.com/img/img02/8/5/30/pedrotorresfilho/f_P5220005m_3371e98.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/5/30/pedrotorresfilho/f_P5220005m_3371e98.jpg)

http://img01.picoodle.com/img/img01/8/5/30/pedrotorresfilho/f_P5220007m_feba7f5.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/30/pedrotorresfilho/f_P5220007m_feba7f5.jpg)

http://img03.picoodle.com/img/img03/8/5/30/pedrotorresfilho/f_P5220009m_f162d9f.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/30/pedrotorresfilho/f_P5220009m_f162d9f.jpg)

http://img01.picoodle.com/img/img01/8/5/30/pedrotorresfilho/f_P5220012m_9ac3bee.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/30/pedrotorresfilho/f_P5220012m_9ac3bee.jpg)

http://img01.picoodle.com/img/img01/8/5/30/pedrotorresfilho/f_P5220013m_363d9de.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/30/pedrotorresfilho/f_P5220013m_363d9de.jpg)

http://img01.picoodle.com/img/img01/8/5/30/pedrotorresfilho/f_P5220014m_16c5427.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/30/pedrotorresfilho/f_P5220014m_16c5427.jpg)

http://img01.picoodle.com/img/img01/8/5/30/pedrotorresfilho/f_P5220016m_c274822.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/5/30/pedrotorresfilho/f_P5220016m_c274822.jpg)

http://img03.picoodle.com/img/img03/8/5/30/pedrotorresfilho/f_P5220021m_c290dd3.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/30/pedrotorresfilho/f_P5220021m_c290dd3.jpg)

http://img03.picoodle.com/img/img03/8/5/30/pedrotorresfilho/f_P5220023m_e58d8d3.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/5/30/pedrotorresfilho/f_P5220023m_e58d8d3.jpg)

I’ll finish it tomorrow.

See you

Pedro Torres.

[pedrofilho]

Working on the feet and one side panel:
http://img03.picoodle.com/img/img03/8/6/3/pedrotorresfilho/f_P5260020m_cdacfeb.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/6/3/pedrotorresfilho/f_P5260020m_cdacfeb.jpg)

http://img01.picoodle.com/img/img01/8/6/3/pedrotorresfilho/f_P5260024m_f4f624a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/6/3/pedrotorresfilho/f_P5260024m_f4f624a.jpg)

Dry brush paintings:
http://img01.picoodle.com/img/img01/8/6/3/pedrotorresfilho/f_P5260031m_7a1cc6d.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/6/3/pedrotorresfilho/f_P5260031m_7a1cc6d.jpg)

http://img03.picoodle.com/img/img03/8/6/3/pedrotorresfilho/f_P5260032m_9324143.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/6/3/pedrotorresfilho/f_P5260032m_9324143.jpg)

Final result:
http://img03.picoodle.com/img/img03/8/6/3/pedrotorresfilho/f_P5260046m_36917c0.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/6/3/pedrotorresfilho/f_P5260046m_36917c0.jpg)

See you soon !

Pedro Torres.

[pedrofilho]

Feet dry painting:
http://img01.picoodle.com/img/img01/8/6/3/pedrotorresfilho/f_P5270027m_9f5937f.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/6/3/pedrotorresfilho/f_P5270027m_9f5937f.jpg)

The differences:
http://img02.picoodle.com/img/img02/8/6/3/pedrotorresfilho/f_P5270028m_bc07bd2.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/6/3/pedrotorresfilho/f_P5270028m_bc07bd2.jpg)

The final results:
http://img03.picoodle.com/img/img03/8/6/3/pedrotorresfilho/f_P5270029m_1c6e738.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/6/3/pedrotorresfilho/f_P5270029m_1c6e738.jpg)

That’s all for now, see you!

Pedro Torres.

[pedrofilho]

I’ve got the power:
http://img01.picoodle.com/img/img01/8/6/4/pedrotorresfilho/f_P5270002m_0fda610.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/6/4/pedrotorresfilho/f_P5270002m_0fda610.jpg)

http://img02.picoodle.com/img/img02/8/6/4/pedrotorresfilho/f_P5270003m_1ab31aa.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/6/4/pedrotorresfilho/f_P5270003m_1ab31aa.jpg)

http://img02.picoodle.com/img/img02/8/6/4/pedrotorresfilho/f_P5270004m_aee100c.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/6/4/pedrotorresfilho/f_P5270004m_aee100c.jpg)

Really nice stuff !
http://img03.picoodle.com/img/img03/8/6/4/pedrotorresfilho/f_P5270005m_1d84ac6.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/6/4/pedrotorresfilho/f_P5270005m_1d84ac6.jpg)

Cables sleeving begins:
http://img03.picoodle.com/img/img03/8/6/4/pedrotorresfilho/f_P5270011m_f4e8369.jpg (http://www.picoodle.com/view.php?srv=img03&img=/8/6/4/pedrotorresfilho/f_P5270011m_f4e8369.jpg)

http://img02.picoodle.com/img/img02/8/6/4/pedrotorresfilho/f_P5280013m_dee7644.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/6/4/pedrotorresfilho/f_P5280013m_dee7644.jpg)

Tomorrow I’ll bring more photos of the sleeving process.

See you !

Pedro Torres.

[pedrofilho]

Font sleeving:
http://img02.picoodle.com/img/img02/8/6/5/pedrotorresfilho/f_P5280002m_4c83ffd.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/6/5/pedrotorresfilho/f_P5280002m_4c83ffd.jpg)

http://img02.picoodle.com/img/img02/8/6/5/pedrotorresfilho/f_P5280006m_83da662.jpg (http://www.picoodle.com/view.php?srv=img02&img=/8/6/5/pedrotorresfilho/f_P5280006m_83da662.jpg)

http://img01.picoodle.com/img/img01/8/6/5/pedrotorresfilho/f_P5280007m_e32270a.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/6/5/pedrotorresfilho/f_P5280007m_e32270a.jpg)

Done (the main cable will be hidden, so, I don’t want it glowing)
http://img01.picoodle.com/img/img01/8/6/5/pedrotorresfilho/f_P5280010m_2ca7576.jpg (http://www.picoodle.com/view.php?srv=img01&img=/8/6/5/pedrotorresfilho/f_P5280010m_2ca7576.jpg)

Now, I’ll do ‘the one’ cable.

See you,

Pedro Torres.

[pedrofilho]

Another cable done, PCI-E:
http://img31.picoodle.com/img/img31/8/6/6/pedrotorresfilho/f_P5290001m_82f5595.jpg (http://www.picoodle.com/view.php?srv=img31&img=/8/6/6/pedrotorresfilho/f_P5290001m_82f5595.jpg)

Now, I’ll do a cable to connect all the gears.

See you soon,

Pedro Torres.

[pedrofilho]

Small back panel plate:
http://img30.picoodle.com/img/img30/8/6/10/pedrotorresfilho/f_P6020007m_a17077b.jpg (http://www.picoodle.com/view.php?srv=img30&img=/8/6/10/pedrotorresfilho/f_P6020007m_a17077b.jpg)

Routed with Dremel
http://img38.picoodle.com/img/img38/8/6/10/pedrotorresfilho/f_P6020008m_3a5461b.jpg (http://www.picoodle.com/view.php?srv=img38&img=/8/6/10/pedrotorresfilho/f_P6020008m_3a5461b.jpg)

Sanded:
http://img37.picoodle.com/img/img37/8/6/10/pedrotorresfilho/f_P6020010m_304bccd.jpg (http://www.picoodle.com/view.php?srv=img37&img=/8/6/10/pedrotorresfilho/f_P6020010m_304bccd.jpg)

Fits:
http://img36.picoodle.com/img/img36/8/6/10/pedrotorresfilho/f_P6020011m_cd247eb.jpg (http://www.picoodle.com/view.php?srv=img36&img=/8/6/10/pedrotorresfilho/f_P6020011m_cd247eb.jpg)
See you later !

[pedrofilho]

Working on front panel with fiberglass:
http://img27.picoodle.com/img/img27/8/6/10/pedrotorresfilho/f_P6020001m_24ee6b2.jpg (http://www.picoodle.com/view.php?srv=img27&img=/8/6/10/pedrotorresfilho/f_P6020001m_24ee6b2.jpg)

Cut the bended part (not necessary anymore)
http://img35.picoodle.com/img/img35/8/6/10/pedrotorresfilho/f_P6020003m_539fa04.jpg (http://www.picoodle.com/view.php?srv=img35&img=/8/6/10/pedrotorresfilho/f_P6020003m_539fa04.jpg)

Preparing the fiberglass:
http://img36.picoodle.com/img/img36/8/6/10/pedrotorresfilho/f_P6020008m_cab6b08.jpg (http://www.picoodle.com/view.php?srv=img36&img=/8/6/10/pedrotorresfilho/f_P6020008m_cab6b08.jpg)

Cutting:
http://img33.picoodle.com/img/img33/8/6/10/pedrotorresfilho/f_P6020009m_e830f89.jpg (http://www.picoodle.com/view.php?srv=img33&img=/8/6/10/pedrotorresfilho/f_P6020009m_e830f89.jpg)

Opening the center hole:
http://img30.picoodle.com/img/img30/8/6/10/pedrotorresfilho/f_P6020010m_116626f.jpg (http://www.picoodle.com/view.php?srv=img30&img=/8/6/10/pedrotorresfilho/f_P6020010m_116626f.jpg)

The fiberglass pieces needed:
http://img39.picoodle.com/img/img39/8/6/10/pedrotorresfilho/f_P6020011m_c1b84a1.jpg (http://www.picoodle.com/view.php?srv=img39&img=/8/6/10/pedrotorresfilho/f_P6020011m_c1b84a1.jpg)

Fiberglass to fix the depression:
http://img35.picoodle.com/img/img35/8/6/10/pedrotorresfilho/f_P6020012m_3f0f150.jpg (http://www.picoodle.com/view.php?srv=img35&img=/8/6/10/pedrotorresfilho/f_P6020012m_3f0f150.jpg)

Done:
http://img37.picoodle.com/img/img37/8/6/10/pedrotorresfilho/f_P6020013m_0efb402.jpg (http://www.picoodle.com/view.php?srv=img37&img=/8/6/10/pedrotorresfilho/f_P6020013m_0efb402.jpg)

When it dry I’ll paint and come back with more photos.

See you really soon !

Pedro Torres.

[pedrofilho]

Front panel paintings:
First hand, black:
http://img32.picoodle.com/img/img32/8/6/11/pedrotorresfilho/f_P6030001m_6abf8d0.jpg (http://www.picoodle.com/view.php?srv=img32&img=/8/6/11/pedrotorresfilho/f_P6030001m_6abf8d0.jpg)

The regeneration chamber painting:
http://img32.picoodle.com/img/img32/8/6/11/pedrotorresfilho/f_P6030002m_6955a53.jpg (http://www.picoodle.com/view.php?srv=img32&img=/8/6/11/pedrotorresfilho/f_P6030002m_6955a53.jpg)
First layer, natural shadow (brownie):
http://img27.picoodle.com/img/img27/8/6/11/pedrotorresfilho/f_P6030003m_3983067.jpg (http://www.picoodle.com/view.php?srv=img27&img=/8/6/11/pedrotorresfilho/f_P6030003m_3983067.jpg)

Second layer, ochre:
http://img40.picoodle.com/img/img40/8/6/11/pedrotorresfilho/f_P6030004m_2034193.jpg (http://www.picoodle.com/view.php?srv=img40&img=/8/6/11/pedrotorresfilho/f_P6030004m_2034193.jpg)

Third layer, titanium white:
http://img37.picoodle.com/img/img37/8/6/11/pedrotorresfilho/f_P6030005m_c806b85.jpg (http://www.picoodle.com/view.php?srv=img37&img=/8/6/11/pedrotorresfilho/f_P6030005m_c806b85.jpg)

The results:
http://img27.picoodle.com/img/img27/8/6/11/pedrotorresfilho/f_P6030008m_a0602b5.jpg (http://www.picoodle.com/view.php?srv=img27&img=/8/6/11/pedrotorresfilho/f_P6030008m_a0602b5.jpg)

A better shot of colors:
http://img36.picoodle.com/img/img36/8/6/11/pedrotorresfilho/f_P6030024m_d9c07dc.jpg (http://www.picoodle.com/view.php?srv=img36&img=/8/6/11/pedrotorresfilho/f_P6030024m_d9c07dc.jpg)

See you tomorrow with the front panel window in plexi-glass.

Pedro Torres.

[pedrofilho]

Damn, I had to register just to leave a comment in this baby!
AWESOME job Pedro, you have some mad skills!

A question:
Did you plan this ALL from the beggining(which tools to use, materials, etcetera) or you bought them as needed?

Você é o cara! Se melhorar estraga!! Hehe.
(Sorry for the portuguese guys... Had to congratulate him in good old portuguese too!)

Thank you very much Axell, I'm glad to have some fellow citzens around the globe. Actually I was building and the ideas were coming up, so, I mad many changes along the construction of this case.

The main tool is the Dremel and a lot of other materials, like fiber glass, body filler, sanding and a lot of paint job and modeling.

And, yes, I bought then as I needed. Each new creation requires specific tools and materials. Most of the case was projected, but, a nice part of then just was happenig as I build it.

Thank you again for the visit and you kindly coment.

See you !

Working on front panel plexi-glass window:
http://img30.picoodle.com/img/img30/8/6/12/pedrotorresfilho/f_P6040001m_bad9d50.jpg (http://www.picoodle.com/view.php?srv=img30&img=/8/6/12/pedrotorresfilho/f_P6040001m_bad9d50.jpg)

Bending the borders:
http://img32.picoodle.com/img/img32/8/6/12/pedrotorresfilho/f_P6050006m_3221302.jpg (http://www.picoodle.com/view.php?srv=img32&img=/8/6/12/pedrotorresfilho/f_P6050006m_3221302.jpg)

Bended:
http://img30.picoodle.com/img/img30/8/6/12/pedrotorresfilho/f_P6050007m_36b5aaa.jpg (http://www.picoodle.com/view.php?srv=img30&img=/8/6/12/pedrotorresfilho/f_P6050007m_36b5aaa.jpg)

The other side:
http://img29.picoodle.com/img/img29/8/6/12/pedrotorresfilho/f_P6050008m_ebee5da.jpg (http://www.picoodle.com/view.php?srv=img29&img=/8/6/12/pedrotorresfilho/f_P6050008m_ebee5da.jpg)

Bending the middle:
http://img37.picoodle.com/img/img37/8/6/12/pedrotorresfilho/f_P6050009m_d0ae383.jpg (http://www.picoodle.com/view.php?srv=img37&img=/8/6/12/pedrotorresfilho/f_P6050009m_d0ae383.jpg)

Done:
http://img33.picoodle.com/img/img33/8/6/12/pedrotorresfilho/f_P6050011m_a19fb6b.jpg (http://www.picoodle.com/view.php?srv=img33&img=/8/6/12/pedrotorresfilho/f_P6050011m_a19fb6b.jpg)

Almost there:
http://img30.picoodle.com/img/img30/8/6/12/pedrotorresfilho/f_P6050012m_52a4412.jpg (http://www.picoodle.com/view.php?srv=img30&img=/8/6/12/pedrotorresfilho/f_P6050012m_52a4412.jpg)

After a few adjustments, the result:
http://img35.picoodle.com/img/img35/8/6/12/pedrotorresfilho/f_P6050013m_8392fd2.jpg (http://www.picoodle.com/view.php?srv=img35&img=/8/6/12/pedrotorresfilho/f_P6050013m_8392fd2.jpg)

Fits perfectly.

See you tomorrow with more news.

Pedro Torres.

[pedrofilho]

Exterior texture starts:
http://img28.picoodle.com/img/img28/8/6/16/pedrotorresfilho/f_P6080001m_f599844.jpg (http://www.picoodle.com/view.php?srv=img28&img=/8/6/16/pedrotorresfilho/f_P6080001m_f599844.jpg)

Black base:
http://img27.picoodle.com/img/img27/8/6/16/pedrotorresfilho/f_P6080002m_f2290e4.jpg (http://www.picoodle.com/view.php?srv=img27&img=/8/6/16/pedrotorresfilho/f_P6080002m_f2290e4.jpg)

Tomorrow I’ll do the texturing paintings and bring the photos.

See you,

Pedro Torres.

[pedrofilho]

Texture paintings:
First of all, fix some irregularities of UFO surface:
http://img38.picoodle.com/img/img38/8/6/17/pedrotorresfilho/f_P6090001m_e8002f5.jpg (http://www.picoodle.com/view.php?srv=img38&img=/8/6/17/pedrotorresfilho/f_P6090001m_e8002f5.jpg)

http://img40.picoodle.com/img/img40/8/6/17/pedrotorresfilho/f_P6090015m_acf819e.jpg (http://www.picoodle.com/view.php?srv=img40&img=/8/6/17/pedrotorresfilho/f_P6090015m_acf819e.jpg)

http://img28.picoodle.com/img/img28/8/6/17/pedrotorresfilho/f_P6090018m_41c4c54.jpg (http://www.picoodle.com/view.php?srv=img28&img=/8/6/17/pedrotorresfilho/f_P6090018m_41c4c54.jpg)

The first part to be painted:
http://img31.picoodle.com/img/img31/8/6/17/pedrotorresfilho/f_P6090003m_45d7506.jpg (http://www.picoodle.com/view.php?srv=img31&img=/8/6/17/pedrotorresfilho/f_P6090003m_45d7506.jpg)

First layer, Prussian blue:
http://img39.picoodle.com/img/img39/8/6/17/pedrotorresfilho/f_P6090005m_a160b1e.jpg (http://www.picoodle.com/view.php?srv=img39&img=/8/6/17/pedrotorresfilho/f_P6090005m_a160b1e.jpg)

After a second and third layer, titanium white and ochre:
http://img40.picoodle.com/img/img40/8/6/17/pedrotorresfilho/f_P6090009m_ca50d0a.jpg (http://www.picoodle.com/view.php?srv=img40&img=/8/6/17/pedrotorresfilho/f_P6090009m_ca50d0a.jpg)

http://img26.picoodle.com/img/img26/8/6/17/pedrotorresfilho/f_P6090011m_6651967.jpg (http://www.picoodle.com/view.php?srv=img26&img=/8/6/17/pedrotorresfilho/f_P6090011m_6651967.jpg)

The upside:
http://img36.picoodle.com/img/img36/8/6/17/pedrotorresfilho/f_P6090012m_bc6462f.jpg (http://www.picoodle.com/view.php?srv=img36&img=/8/6/17/pedrotorresfilho/f_P6090012m_bc6462f.jpg)

Prussian blue:
http://img39.picoodle.com/img/img39/8/6/17/pedrotorresfilho/f_P6090013m_9e48e96.jpg (http://www.picoodle.com/view.php?srv=img39&img=/8/6/17/pedrotorresfilho/f_P6090013m_9e48e96.jpg)

Work done, with flash:
http://img26.picoodle.com/img/img26/8/6/17/pedrotorresfilho/f_P6090014m_c1eb131.jpg (http://www.picoodle.com/view.php?srv=img26&img=/8/6/17/pedrotorresfilho/f_P6090014m_c1eb131.jpg)

Tomorrow I’ll paint the UFO and it’s side panel.

See you,

Pedro Torres.

[pedrofilho]

UFO and it’s side panel painting:

First layer, Prussian blue, the UFO was painted in silver:
http://img26.picoodle.com/img/img26/8/6/18/pedrotorresfilho/f_P6100003m_fc8c638.jpg (http://www.picoodle.com/view.php?srv=img26&img=/8/6/18/pedrotorresfilho/f_P6100003m_fc8c638.jpg)

Second layer, titanium white:
http://img26.picoodle.com/img/img26/8/6/18/pedrotorresfilho/f_P6100005m_68e0b01.jpg (http://www.picoodle.com/view.php?srv=img26&img=/8/6/18/pedrotorresfilho/f_P6100005m_68e0b01.jpg)

Third layer, ochre:
http://img39.picoodle.com/img/img39/8/6/18/pedrotorresfilho/f_P6100006m_a2786bb.jpg (http://www.picoodle.com/view.php?srv=img39&img=/8/6/18/pedrotorresfilho/f_P6100006m_a2786bb.jpg)

Strobe flash
http://img39.picoodle.com/img/img39/8/6/18/pedrotorresfilho/f_P6100007m_e10f6a3.jpg (http://www.picoodle.com/view.php?srv=img39&img=/8/6/18/pedrotorresfilho/f_P6100007m_e10f6a3.jpg)

This paintings takes 5 days to dry completely, after that, I’ll mount all the case.

See you there,

Pedro Torres.

[pedrofilho]

Case feet repair and internal side panel painting:
During the texturing I let some body filler escape to the plexi-glass and, now, had to repair it:
http://img39.picoodle.com/img/img39/8/6/20/pedrotorresfilho/f_P6120001m_3710825.jpg (http://www.picoodle.com/view.php?srv=img39&img=/8/6/20/pedrotorresfilho/f_P6120001m_3710825.jpg)

First, I removed the excess of body filler with the Dremel sander:
http://img28.picoodle.com/img/img28/8/6/20/pedrotorresfilho/f_P6120002m_81d72e0.jpg (http://www.picoodle.com/view.php?srv=img28&img=/8/6/20/pedrotorresfilho/f_P6120002m_81d72e0.jpg)

Finished one:
http://img29.picoodle.com/img/img29/8/6/20/pedrotorresfilho/f_P6120004m_0d1fce0.jpg (http://www.picoodle.com/view.php?srv=img29&img=/8/6/20/pedrotorresfilho/f_P6120004m_0d1fce0.jpg)

Got this:
http://img31.picoodle.com/img/img31/8/6/20/pedrotorresfilho/f_P6120005m_8ec1e6d.jpg (http://www.picoodle.com/view.php?srv=img31&img=/8/6/20/pedrotorresfilho/f_P6120005m_8ec1e6d.jpg)

Sanded one by one with 150 paper to remove every body filler traces:
http://img39.picoodle.com/img/img39/8/6/20/pedrotorresfilho/f_P6120006m_80f4b6e.jpg (http://www.picoodle.com/view.php?srv=img39&img=/8/6/20/pedrotorresfilho/f_P6120006m_80f4b6e.jpg)

Used the polishing Dremel bit with silicone to smooth the border and get a nice shiny:
http://img33.picoodle.com/img/img33/8/6/20/pedrotorresfilho/f_P6120007m_0ad3aa2.jpg (http://www.picoodle.com/view.php?srv=img33&img=/8/6/20/pedrotorresfilho/f_P6120007m_0ad3aa2.jpg)

In action:
http://img33.picoodle.com/img/img33/8/6/20/pedrotorresfilho/f_P6120008m_3cef618.jpg (http://www.picoodle.com/view.php?srv=img33&img=/8/6/20/pedrotorresfilho/f_P6120008m_3cef618.jpg)

This is the result of polishing:
http://img26.picoodle.com/img/img26/8/6/20/pedrotorresfilho/f_P6120012m_ae0f714.jpg (http://www.picoodle.com/view.php?srv=img26&img=/8/6/20/pedrotorresfilho/f_P6120012m_ae0f714.jpg)

Then I painted the scratched areas using the same colors:
http://img34.picoodle.com/img/img34/8/6/20/pedrotorresfilho/f_P6120013m_533d64c.jpg (http://www.picoodle.com/view.php?srv=img34&img=/8/6/20/pedrotorresfilho/f_P6120013m_533d64c.jpg)

Ochre:
http://img31.picoodle.com/img/img31/8/6/20/pedrotorresfilho/f_P6120014m_25d70c1.jpg (http://www.picoodle.com/view.php?srv=img31&img=/8/6/20/pedrotorresfilho/f_P6120014m_25d70c1.jpg)

Repair done:
http://img27.picoodle.com/img/img27/8/6/20/pedrotorresfilho/f_P6120015m_9002fa2.jpg (http://www.picoodle.com/view.php?srv=img27&img=/8/6/20/pedrotorresfilho/f_P6120015m_9002fa2.jpg)

All the feet painted and waiting for the titanium white with a dry paint.
http://img30.picoodle.com/img/img30/8/6/20/pedrotorresfilho/f_P6120016m_81390c7.jpg (http://www.picoodle.com/view.php?srv=img30&img=/8/6/20/pedrotorresfilho/f_P6120016m_81390c7.jpg)

Final result:
http://img32.picoodle.com/img/img32/8/6/20/pedrotorresfilho/f_P6120017m_f34573c.jpg (http://www.picoodle.com/view.php?srv=img32&img=/8/6/20/pedrotorresfilho/f_P6120017m_f34573c.jpg)

The ET side panel interior was a mess of colors, so, I decided to paint it in chrome to help the illumination:
http://img32.picoodle.com/img/img32/8/6/20/pedrotorresfilho/f_P6120018m_c43eec0.jpg (http://www.picoodle.com/view.php?srv=img32&img=/8/6/20/pedrotorresfilho/f_P6120018m_c43eec0.jpg)

This is the result (really shiny, mirror finishing):
http://img30.picoodle.com/img/img30/8/6/20/pedrotorresfilho/f_P6120021m_11d2027.jpg (http://www.picoodle.com/view.php?srv=img30&img=/8/6/20/pedrotorresfilho/f_P6120021m_11d2027.jpg)

That’s it for now. Be back soon.

See you,

Pedro Torres.

[pedrofilho]

Arrived ! The items I's missing to mount the case. The block for the VGA volt regulator, a pair of CC and a switch.

next wednesday it'll be mounted.

See you,

Pedro Torres.

[pedrofilho]

hey petro,

one question,
youve painted the side panel in chrome look, but the rest of the interior is bright yellow, isnt it? do leave that, or will it be shiny 8)

When I finish this 2nd fase will start a 3rd fase and maybe I should change the interior painting to chrome too, but, this time I'll leave this UV yellow.

After painting the side panel in chrome I confess to be inclined to paint everything the same way, but, I'll decide it in 3rd fase.

Thank's for asking,

Pedro Torres.

[pedrofilho]

What kind of chrome paint did you use?

Looks awesome, but I think I liked the flourescent green better. :D

Hi The Black Pumpkin, I used a metal paint, called Renner. The result becames shiny due a lot of sanding work I did before, in preparation.

The UV yellow inside will remains, I just painted the side windows in chrome to improve ilummination. I won a pair of ACRyan CC UV from performance-pcs.com and it will be a nice update to lightings stuff.

Thanks for your kindly coment. See you,

Pedro Torres.

[pedrofilho]

Doing a single cable to connect all the equipments:

The victim:
http://img35.picoodle.com/img/img35/8/6/25/pedrotorresfilho/f_P6130002m_f5c657a.jpg (http://www.picoodle.com/view.php?srv=img35&img=/8/6/25/pedrotorresfilho/f_P6130002m_f5c657a.jpg)

First I put a blue UV reactive sleeve covering the main cable:
http://img29.picoodle.com/img/img29/8/6/25/pedrotorresfilho/f_P6160003m_e7f807f.jpg (http://www.picoodle.com/view.php?srv=img29&img=/8/6/25/pedrotorresfilho/f_P6160003m_e7f807f.jpg)

Change some connectors to blue UV reactive ones
http://img37.picoodle.com/img/img37/8/6/25/pedrotorresfilho/f_P6170004m_7385876.jpg (http://www.picoodle.com/view.php?srv=img37&img=/8/6/25/pedrotorresfilho/f_P6170004m_7385876.jpg)

Prolongation of the cable
http://img34.picoodle.com/img/img34/8/6/25/pedrotorresfilho/f_P6170006m_a655e7e.jpg (http://www.picoodle.com/view.php?srv=img34&img=/8/6/25/pedrotorresfilho/f_P6170006m_a655e7e.jpg)

Separation done:
http://img37.picoodle.com/img/img37/8/6/25/pedrotorresfilho/f_P6170007m_f67d1ce.jpg (http://www.picoodle.com/view.php?srv=img37&img=/8/6/25/pedrotorresfilho/f_P6170007m_f67d1ce.jpg)

Connecting female Molex pins
http://img40.picoodle.com/img/img40/8/6/25/pedrotorresfilho/f_P6170008m_8673dc7.jpg (http://www.picoodle.com/view.php?srv=img40&img=/8/6/25/pedrotorresfilho/f_P6170008m_8673dc7.jpg)

Verifying the connections:
http://img39.picoodle.com/img/img39/8/6/25/pedrotorresfilho/f_P6170011m_1aefa67.jpg (http://www.picoodle.com/view.php?srv=img39&img=/8/6/25/pedrotorresfilho/f_P6170011m_1aefa67.jpg)

First addiction:
http://img28.picoodle.com/img/img28/8/6/25/pedrotorresfilho/f_P6170012m_8000900.jpg (http://www.picoodle.com/view.php?srv=img28&img=/8/6/25/pedrotorresfilho/f_P6170012m_8000900.jpg)

Another part of the sleeve process
http://img35.picoodle.com/img/img35/8/6/25/pedrotorresfilho/f_P6170013m_4bd6803.jpg (http://www.picoodle.com/view.php?srv=img35&img=/8/6/25/pedrotorresfilho/f_P6170013m_4bd6803.jpg)

Cable done:
http://img28.picoodle.com/img/img28/8/6/25/pedrotorresfilho/f_P6170014m_5e82fb6.jpg (http://www.picoodle.com/view.php?srv=img28&img=/8/6/25/pedrotorresfilho/f_P6170014m_5e82fb6.jpg)

See you,

Pedro Torres.

[pedrofilho]

Well, I’ll need two fan extension cables, so, I did it, take a look:

The material I used:
http://img36.picoodle.com/img/img36/8/6/26/pedrotorresfilho/f_P6180001m_bf46446.jpg (http://www.picoodle.com/view.php?srv=img36&img=/8/6/26/pedrotorresfilho/f_P6180001m_bf46446.jpg)

A closer look at the connectors:
http://img28.picoodle.com/img/img28/8/6/26/pedrotorresfilho/f_P6180004m_bcb78e4.jpg (http://www.picoodle.com/view.php?srv=img28&img=/8/6/26/pedrotorresfilho/f_P6180004m_bcb78e4.jpg)

First, I did the female connector
http://img31.picoodle.com/img/img31/8/6/26/pedrotorresfilho/f_P6180008m_c2b8ebf.jpg (http://www.picoodle.com/view.php?srv=img31&img=/8/6/26/pedrotorresfilho/f_P6180008m_c2b8ebf.jpg)

Then I put the sleeve:
http://img36.picoodle.com/img/img36/8/6/26/pedrotorresfilho/f_P6180010m_04c2dea.jpg (http://www.picoodle.com/view.php?srv=img36&img=/8/6/26/pedrotorresfilho/f_P6180010m_04c2dea.jpg)

And fix it with a heatshrink
http://img37.picoodle.com/img/img37/8/6/26/pedrotorresfilho/f_P6180011m_6cad9ed.jpg (http://www.picoodle.com/view.php?srv=img37&img=/8/6/26/pedrotorresfilho/f_P6180011m_6cad9ed.jpg)

So, I started on the other side of the cable:
http://img34.picoodle.com/img/img34/8/6/26/pedrotorresfilho/f_P6180012m_55d8cee.jpg (http://www.picoodle.com/view.php?srv=img34&img=/8/6/26/pedrotorresfilho/f_P6180012m_55d8cee.jpg)

Soldered the pins and fix with heatshrink :
http://img38.picoodle.com/img/img38/8/6/26/pedrotorresfilho/f_P6180013m_1623008.jpg (http://www.picoodle.com/view.php?srv=img38&img=/8/6/26/pedrotorresfilho/f_P6180013m_1623008.jpg)

The cable is done:
http://img29.picoodle.com/img/img29/8/6/26/pedrotorresfilho/f_P61800014m_6183853.jpg (http://www.picoodle.com/view.php?srv=img29&img=/8/6/26/pedrotorresfilho/f_P61800014m_6183853.jpg)

Two units:
http://img38.picoodle.com/img/img38/8/6/26/pedrotorresfilho/f_P61800015m_ba5f785.jpg (http://www.picoodle.com/view.php?srv=img38&img=/8/6/26/pedrotorresfilho/f_P61800015m_ba5f785.jpg)

See you later with more news.

Pedro Torres.

[pedrofilho]

This looks really cool Pedro!!!!
Saludos!

w00t w00t :D

Hey buddy, Saludos to you too. Be wellcome aways.

Thank you.


This reminds me, I've got some work to do on my fans for the Frankenstripe...

Superb work man, I've been following this since the beginning.

I know that DrumThumper, I aways see you around. Get hands on work to your Frankenstripe, it desirve a nice cable sleeving too.

Thank you.


Vote for Pedro!!!

Hello Jon, I appreciate that. :D

Thank you for constantly supporting us.

See you soon with more sleeves. That's the finals to mount the case, the end is near. (end of the second fase)

Pedro Torres.

[pedrofilho]

wow nice shiny paint job on the side panel. i should get some cable sleeves too, since i don't have a pc yet, i can work on making the case i have better looking. good job !

The cable sleeving helps a lot the air flow. It's a good idea to do the same on your next PC.

See you soon with more sleeves and cable management.

Pedro Torres.

[pedrofilho]

Got today that missing items to finish the case, take a look:
This will turn on/off all the lights:
http://img29.picoodle.com/img/img29/8/7/2/pedrotorresfilho/f_P6240002m_effeb0a.jpg (http://www.picoodle.com/view.php?srv=img29&img=/8/7/2/pedrotorresfilho/f_P6240002m_effeb0a.jpg)

Came with accessories, very nice:
http://img33.picoodle.com/img/img33/8/7/2/pedrotorresfilho/f_P6240003m_aa52993.jpg (http://www.picoodle.com/view.php?srv=img33&img=/8/7/2/pedrotorresfilho/f_P6240003m_aa52993.jpg)

The glitter to front panel paintings:
http://img35.picoodle.com/img/img35/8/7/2/pedrotorresfilho/f_P6240005m_029e954.jpg (http://www.picoodle.com/view.php?srv=img35&img=/8/7/2/pedrotorresfilho/f_P6240005m_029e954.jpg)

Royal blue to front panel:
http://img35.picoodle.com/img/img35/8/7/2/pedrotorresfilho/f_P6240008m_27e325e.jpg (http://www.picoodle.com/view.php?srv=img35&img=/8/7/2/pedrotorresfilho/f_P6240008m_27e325e.jpg)

This is the WC block to the VGA volt regulator chipset by Koolance (extremely well finished material):
http://img35.picoodle.com/img/img35/8/7/2/pedrotorresfilho/f_P6240010m_84a353a.jpg (http://www.picoodle.com/view.php?srv=img35&img=/8/7/2/pedrotorresfilho/f_P6240010m_84a353a.jpg)

And this was a birthday gift I received from performance-pcs.com:
http://img29.picoodle.com/img/img29/8/7/2/pedrotorresfilho/f_P6240011am_f3d7d3c.jpg (http://www.picoodle.com/view.php?srv=img29&img=/8/7/2/pedrotorresfilho/f_P6240011am_f3d7d3c.jpg)

Now, I’ll paint the front panel and mount the case finally.

See you soon,

Pedro Torres.

[pedrofilho]

Sick!

:D Glad you liked it. Hope you like the rest of the case. Today I'll paint the front panel and tomorrow I'll start mounting it.

See you soon,


birthday gift?? i want one!!! where did you get the switch from?

Yeah ! I just told to Hank Baron from performance-pcs.com about my birthday and he gives me this cool CC pair. These stuff was all bought in the PPCS.

This is a nice switch, very well made and very beautyfull. I recommend.

See you later,

Pedro Torres.

[pedrofilho]

Am I the only one here who read that, and had Borat's voice pop into my head?

Pedro, this is fast becoming one of my favorite (if not my absolute favorite) mods of all time. Keep it up!

Hope you liked it more when done. Glad to figure between your favorites mods. Today I did a little adjustmente of the center hole to fits with new switch.

See you tomorrow and thank you for the visit.


I WAS QUOTED!

Anyway i cant wait to see this when its fully done. U should film a video instead of pics so we can see how that switch works! ;)

I'll do that. When it be done, I'll make a small video of it in action and the switch working on.

See you later.


http://www.performance-pcs.com/catalog/index.php?main_page=product_info&products_id=21776
i think thats the switch.

Exactly that one. Today I did the first layer of paint and tomorrow I'll apply the glitter. The paint I used takes 24h to dry.

See you tomorrow,

Front panel adjustment and painting
Remake of center hole to match the new switch requirement:
http://img40.picoodle.com/img/img40/8/7/3/pedrotorresfilho/f_P6250001m_9455f88.jpg (http://www.picoodle.com/view.php?srv=img40&img=/8/7/3/pedrotorresfilho/f_P6250001m_9455f88.jpg)

First hand of paint, colonial blue:
http://img35.picoodle.com/img/img35/8/7/3/pedrotorresfilho/f_P6250018m_24edba1.jpg (http://www.picoodle.com/view.php?srv=img35&img=/8/7/3/pedrotorresfilho/f_P6250018m_24edba1.jpg)

Tomorrow I’ll apply the glitter and start mounting the case.

See you there,

Pedro Torres.

[pedrofilho]

cool!

You wouldn't believe, but, I messed it up with this paint and have to remake all the process again. Today I'll paint it again and tomorrow I'll apply the glitter.

Thank you for the visiit.

Pedro Torres.

[pedrofilho]

After a mess on paint, I did a body filler job and sanded it all again:
http://img29.picoodle.com/img/img29/9/7/14/pedrotorresfilho/f_P7060017m_eba093f.jpg (http://www.picoodle.com/view.php?srv=img29&img=/9/7/14/pedrotorresfilho/f_P7060017m_eba093f.jpg)

http://img35.picoodle.com/img/img35/9/7/14/pedrotorresfilho/f_P7060018m_8d24fe2.jpg (http://www.picoodle.com/view.php?srv=img35&img=/9/7/14/pedrotorresfilho/f_P7060018m_8d24fe2.jpg)

Tomorrow I’ll paint it again and finish it.

See you,

Pedro Torres.