DnA

[p0Pe]

DnA – a casemod by p0Pe

Sponsored by

www.coolbits.dk
&
www.matronics.dk

Hello again fokes:) this is the newest projekt i have begun.

The project is going to be build apon an antec P190 case wich I recently got my fingers on (needed a powersupply and since the case comes with 1200 Watts of power, 650W & 550W that was another reason to buy it)


The plans is a following:
1: Make cover plates for most of the interior stuff
2: maybe cut a window beside of the big 250 mm cooler
3: place reservoir on the top
4: watercool the hell out of the punk!
5: make a black & white colour scheme. black fluid, white light.


So what do I need for this? Well… lets start with the BIG thingie!
I got my hands on this lovely thing:
http://tosed.dk/billeder/DnA/Mora.JPG
The MO-RA 2PRO radiator! 9*120 mm! that’s 1080 mm of cooling dudes! So I hope that this ting can passive cool my system which consists of following:
AMD phenom X4 9850 BE
Ati X1950XT-X
In these 2 things is about 300 Watts of heat that needs to be dealt with. In my current setup (scrapheap challenge) this is done by a 120,3 mm radiator with idle temps @ 40/45 C. so I hope to keep these temps, or beat them:D

and for the case i got the P190
http://tosed.dk/billeder/DnA/P1962.jpg




Lets begin
First of all.. there is some smaller damage on the case because the previous owner had a leak in his system, which he blamed on the huge MO-RA radiator, because his pump literally blew up xD.
http://www.tosed.dk/billeder/DnA/DSC01271.jpg
I did prove him wrong though. In the same system as he had the MO-RA raddy he had 2 of the little handy things called quick connectors (the things that closes the waterflow when taken apart).
http://www.tosed.dk/billeder/DnA/DSC01270.jpg
Now, I knew that these would restrict the waterflow, I just didn’t knew how much, so I made a test, which can be seen here:
http://www.thebestcasescenario.com/forum/showthread.php?t=15352
as you can see they absolutely KILL the flow of the system, so I decided to put them in the “keeper” box:D

the first thing I did was of course a lot of thinking but I have no pic´s of that sry:/
then I made up cardbox models of how I wanted the whole thing to look:
http://www.tosed.dk/billeder/DnA/DSC01257.jpg
I put a model in the top to cover the two 140 mm fans. IMO they were way to visible.
Then I made some for the 5.25 bay, and both hdd cages.
Then I made some sketches for how they could possibly end up looking:
http://tosed.dk/billeder/DnA/sketch1.jpg
The big plate is the one that has to cover up the 2*140 mm fans, and some wires. The other ones is the three you also see in the cardbox models at the bays.
Then I mounted the radiator on the left side of the case. Since I cant get the radiator off without bleeding the system, I didn’t wanted to have it on the right side so that I couldn’t get into all the hardware easily.
The thing is mounted with something that looks like mother board spacers. Ill maybe post a pic later on, but here it is on the case side:
http://www.tosed.dk/billeder/DnA/DSC01259.jpg
(the case side, and the radiator has a weight of 7.2 kilo´s alone!!!)
This fan will make sure that my system don’t overheat in any circumstances lol:
http://www.tosed.dk/billeder/DnA/DSC01264.jpg

Just a little comparison to and ordinary P182 case (the P190 is almost 10 cm longer xD)
http://www.tosed.dk/billeder/DnA/DSC01266.jpg
And here you see the whole the previous owner made for the radiator. He had it on the side with the huge fan. Don’t know how ill hide these… ill find out xD
http://www.tosed.dk/billeder/DnA/DSC01268.jpg

This is how I plan to mount the pump. I am using a ddc+ pump and am gonna pair it with a XSPC reservoir top:
http://www.tosed.dk/billeder/DnA/DSC01275.jpg

And a little overview. You can see the pump, and another cardboard at the rear fan. Ill post sketches of this later on:)
http://www.tosed.dk/billeder/DnA/DSC01277.jpg
You might notice that I have taken the included fan holder off in the PSU section. I did this because I think its big and clumsy. So I threw it out, and mounted some fan grills on the fan because I didn’t wanted to have the cables from the PSU´s conflicting with the fan…
http://www.tosed.dk/billeder/DnA/DSC01279.jpg
As seen in this picture of an P182 the cables from the PSU comes very close to the fan :S
http://www.tosed.dk/billeder/DnA/DSC01282.jpg
http://www.tosed.dk/billeder/DnA/DSC01284.jpg
That’s it:) ill update… yeah.. when I get something done lol…
All that’s left to do is to show this pic of the whole mombo with the raddy on the side… damn that thing is big!
http://www.tosed.dk/billeder/DnA/DSC01285.jpg

Have fun!:D

[Enigma]

Yeah, thats a cruel mother of a case you've got there p0Pe :)
This is going to be interesting to follow !!!

[jdbnsn]

woohoo! Another project by the pontiff!

[Acey]

wow... disclosed yesterday bout the rad and starts today? thats fast mate

[The_Crippler]

Whoa, mama! That's a decent-sized rad right there.

...and what happened to the former owner of that case is what has really kept me from going the water-cooling route just yet. Too scared that I'll destroy everything.

+Rep

[p0Pe]

yeah.. it did cost him a few harddrives lol... but as you see in the link i posted that was purely beacuse of the quick connectors:P so as long as your carefull, its safe and colder:D
the shop i have to order vital parts from is closed duo to vacation, and cant get anything cut in the next 2 weeks either so i have plenty of time to make sketches and .cad drawings so that i can send all of the stuff and hopefully complete this mod quicker than the last one xD

[The_Crippler]

...but as you see in the link i posted that was purely beacuse of the quick connectors:P so as long as your carefull, its safe and colder:D


Well, your link crashed my browser several times when I tried it this morning, so I'll just have to take your word on it...:rolleyes:

[p0Pe]

then just try to save it from this link:) its the one named flow test in the bottom:)

http://tosed.dk/billeder/DnA/

should work
(what browser are you using? i remember firefox 2.0 had that fault)

[FuzzyPlushroom]

That's one hell of a radiator! Been considering taking a window air conditioner apart, but that'd actually be a fair bit smaller than this...! Nice huge case for it too, can't wait to see how this turns out.

[p0Pe]

yeah the raddy is a tad big;) but ill need it XD or not lol

Back again with new parts:) (sry for crappy pics, only got cell atm:/ )

I ordered a fan for the raddy, and a reservoir top for my ddc pump (this is the best top for the ddc pumps atm!).

http://tosed.dk/billeder/DnA/DSC00061.jpg

And as you see there is 2 fans behind the pump! This is because I wanted a window in the side, but there was a big fan in the way. So instead of cutting and filling to my hands started bleeding I used the hole that was already there.

First I removed the fan and the dust filter

http://tosed.dk/billeder/DnA/DSC00062.jpg

And then, a nice window with a fine mesh that will fit the rest of the “mesh” theme. In the place where there were a dust filter before I plan to put in some acrylic. Black, or white wich is the overall color scheme.

http://tosed.dk/billeder/DnA/DSC00063.jpg

As you see this is 400 mm of cooling potential:D 2*200 mm fans!!! This should keep the temps down. I will make a cover for them which will sit on top:) will look something like the other fan holes I made in previous sketches.

This is a little view of how big the raddy and fans actually are xD

http://tosed.dk/billeder/DnA/DSC00059.jpg

And how the tubes are gonna enter the case. This will look rather hot IMO!

http://tosed.dk/billeder/DnA/DSC00060.jpg

Did I mention the color of the fluid? ;)

http://tosed.dk/billeder/DnA/F1-0009-2.jpg

BLACK! And with white light this should look AWSOME! (I hope lol)

That was all for now:) next will be finished sketches of the parts that needs to be cut!

Stay cool!
-p0Pe

[FrooP]

oh yeah dude oh yeah 8)

[DocNitrous]

I REALLY dig your rad....

:up:


I think your gonna have monstrous cooling capacity here...

This build will be very interesting

:glasses:

[DonT-FeaR]

cant wait that rad is huge man

[p0Pe]

thx all, and yeah. the raddy added to the two fans should be able to cool quite a few watts. i am gonna try if i can fit 3 or 4 of the 200mm fans on the raddy but i doubt it:( this would be more than i need (hell, i dont even need the fans since this raddy should be able to passive cool my entire setup. but hey, it isnt overkill until something dies from it;) )

i hope to get some time to get sketches made today and update them tonight. so stay tuned for DnA!

[Acey]

Hmm... so are you gonna passive cool and have loads of fans sucking air out of the rad? That would be fun if I have that rad hehe.

[p0Pe]

well since im gonna put fans on it it isnt "passive" anymore:P and im gonna blow air through the raddy. if i pull it through the most part will be sucked from the tiny gab between the fans and the radiator, and dust would be imposible to get of, since it would stick to the side against the case

[Acey]

That would suck... considering its such a cool rad but dust has to spoil it :(

[p0Pe]

Sketches done!

I have made some files that I’m going to send to laser cutting soonest possible. I haven’t made any mounting holes to get the plates to sit on the case, since I will take a closer look at this when I get them. Possibly make them stick with something non-visible such as tape/glue etc. I hope to be able to get them painted blank black, and put some white light in there to shine the whole thing up, should look cool with the white fluid.

On to the sketches. I have made the sketches from these cardboards so it should be easy to see what belongs to where:D

http://tosed.dk/billeder/DnA/DSC01257.jpg

And here is the final sketches.

http://tosed.dk/billeder/DnA/sketch5.jpg

And a view of the top/rear fan covers. The think long line in the metal is where it is going to be bend to cover up the fan sides.

http://tosed.dk/billeder/DnA/sketch4.jpg

It all lying down

http://tosed.dk/billeder/DnA/sketch2.jpg

And wireframe from the top:)

http://tosed.dk/billeder/DnA/sketch3.jpg

That was all for now. I will see if I cant get a hold on the dude who is going to cut the stuff, and see if I can find some sponsors!:D

All that’s left to say now is: have a nice weekend!

[dfigravity]

wow man...I couldn't figure out where the picture of the rad was...everyone kept saying how big it was, but I didn't realize that it is almost the size of a regular atx case! :) This looks cool bro!!!

[The boy 4rm oz]

Have I seen this mod somewhere else before???

[Acey]

Where's the rad standing again?

[p0Pe]

this is were the raddy is gonna sit if you didnt see it:P
http://www.tosed.dk/billeder/DnA/DSC01285.jpg

the boy from oz -

i dont know? i dont hope so:D i havent:P

[The boy 4rm oz]

I could have sworn I have seen the exact same radiator on the exact same case over at Tech Power Up, it may have been a different case but I sure do remember the radiator, it's not one of those things you forget.

[p0Pe]

i searched over there and i found one... he had it on top of a thermaltake xt case:P hm... they say the radiator is underperforming.. im excited to see what it can do

[The boy 4rm oz]

I looked but couldn't find it lol. I knew I had seen the rad but most cases look like an Antec these days lol.

[kris]

Great idea, especialy like the radiator.How heavy it is?
If you'r planing on mounting some fans on radiator i would suggest that u use 4x 120mm fans rather than 2x 140mm.

[p0Pe]

the raddy is about 4 kg heavy.
i use 2*200 mm fans

[p0Pe]

Another update (little one, this time with proper pics:D)
okay lads!
from now one things are gonna get VERY interesting i hope

the awsome news:

GOT SPONSORED!
watercooling and light!!!!

to look who the sponsors are, view first post!


The watercooling! Ohhh the sweet watercooling!!!

This is the things that have to happen!

Dual loops
A harddrive loop with a 120,1 radiator
And
A cpu/gpu loop with a 120,9 radiator

One with black fluid, one with white (oh yeah)

Parts:
1 x MO-RA 2 PRO 120.9

1 x black ice pro 120.1

1 x XSPC bay reservoir pump

2 x Koolance PMP-400 (Laing DDC )

2 x XSPC Laing DDC top

1 x D-Tek Fuzion v2

1 x D-Tek Fuzion v2 Quad Core Mid Chamber

2 x Koolance Inline Reservoir 80mm (225ml)

2 x Koolance HD-57

2 x Feser One - Black (1L)

1 x Feser One - UV Clear/Blue (1L)

1 x CoolLaboratory Liquid Pro

3 x Tygon R-3603 1/4" [9,5/6,4mm] - 50cm

1 x Tygon R-3603 1/2" [19/12,7mm]- 50cm

4 x Koolance G1/4" [6mm, 1/4"]

4 x Koolance push-on G1/4" [9/6mm]

2 x Koolance G1/4" [13mm, 1/2"]


And again, oh yeah

Since I have 2 loops I naturally needs another radiator (120.1)
Where is that going to sit:S?
1
http://tosed.dk/billeder/DnA/DSC01359.jpg

2
http://tosed.dk/billeder/DnA/DSC01362.jpg

And three
http://tosed.dk/billeder/DnA/DSC01363.jpg

The reservoirs are going to sit ontop of the mod like this:

http://tosed.dk/billeder/DnA/DSC01379.jpg

And ofcourse made some cover plates for them

http://tosed.dk/billeder/DnA/res2.jpg

And talking of cover plates, this is what I have made all this time!
http://tosed.dk/billeder/DnA/overall sketch.JPG

And the plate for the 2 200 mm fans
http://tosed.dk/billeder/DnA/raddy side2.JPG

And the sponsor list plate
http://tosed.dk/billeder/DnA/plate55.JPG

ill be back soon:D

[The boy 4rm oz]

Looking really good mate. Congratz on the sponsors. The cover plates look awesome, love the honey comb grills and the Halo-esque text. I can't wait t see how those reservoirs turn out.

[p0Pe]

thx!
and more good newz!
the watercooling parts should be here tommorow!

[The boy 4rm oz]

That is good news. Don't forget to post pics ;) lol.

[Acey]

The plans looks sweet as hell man. Hurry up we want to see the real thing! :D

[p0Pe]

thx:D
well... lasercut parts should be here within a week or 2! so things should really begin to move on from now:D

[DonT-FeaR]

you hit the jackpot thats alot of parts... NICE

[p0Pe]

yeah! got em today!!!:D

and more coming tommorow, hopefully along with light from the light sponsor!!! now i just need the laser cut plates which should be here soon. and then the fun begins;P

[Vision]

Dude, that radiator is BIG. Love the coolant color aswell.

Good work!

Vision

[p0Pe]

thx man! i just got newz that most of the plates are ready tonight! so ill go get them asap.
cant wait:D

sadly i dont have a proper camera atm so no good pics:(

[p0Pe]

now for the fun stuff!

Update. Agian again:) we like them!

Got the laser plates! Sadly 2 of them didn’t fit all that well:(… but they are redrawn and will be here in a few days.
But… teasers! Got all of the watercooling stuff! Thx again coolbits:D almost all watercooling in this case is provided by them! And this is quality stuff!
How all the plates are going to sit! Enjoy, the image will speak for themselves

http://tosed.dk/billeder/DnA/HPIM1331.jpg

http://tosed.dk/billeder/DnA/HPIM1333.jpg

http://tosed.dk/billeder/DnA/HPIM1334.jpg

http://tosed.dk/billeder/DnA/HPIM1336.jpg

Oh and if you are wondering what will circulate the hdd system:

http://tosed.dk/billeder/DnA/HPIM1327.jpg

And a tiny bit of the stuff I got from coolbits! Hdd coolers, and a d-tek fusion v2. !

http://tosed.dk/billeder/DnA/HPIM1337.jpg

And the fan cover plate for the mo-ra. This will be redone because strangly the lasercutter didn’t cut the DnA text. But this will be done next time:D

http://tosed.dk/billeder/DnA/HPIM1338.jpg

And a little teaser of the reservoirs.. this will ofc. Look just like the drawing but didn’t have the spacers so for now its just like this:D

http://tosed.dk/billeder/DnA/HPIM1341.jpg

Thx for reading:)

[The boy 4rm oz]

How much does it cost you to get your stuff lasercut?

The pieces look lovely, shame about the few mis-cuts. The internal panels and water cooling look great. Those reservoirs look sweet mate.

[p0Pe]

it costd me a 160 gb usb harddrive:P "we are here to help each other":D

i know people (best gangster voice) and i know 2 that has a lasercutter for their disposal:D

if you think the res´s looks great now, wait until i get the cover plats on! xD

[DonT-FeaR]

wow that res holder looks sweet

[p0Pe]

thx! now look at this:D only managed to take one picture before the camera went dead on batteries:(

has been filling all day to make it a perfect fit, and now it is! just need to make the spacers for it.

http://tosed.dk/billeder/DnA/IM005064 (1024 x 768).jpg

hope you like it;P

[rendermandan]

Dude, this is looking sweet! +rep,
I have to ask, Where did you get your Laser cutting from?

[p0Pe]

thx dan!
cant tell:P someone might get into truble (unlikely but the change is there)

its a dude i know who works @ a company where they have loads of CNC machines... he is doing my lasercutting and engraving:) and another dude works @ a sign factory that has speacialized in acrylic text signs etc:)

[DonT-FeaR]

wow... thats frigan awsome!!!

[The boy 4rm oz]

Looks as awesome as I thought it would mate. Fantastic work.

My local electronics store sells chrome plated aluminium spacers in packs of 10 in sizes of 5-10mm. You should have a look at your, may find exactly what you are looking for.

[p0Pe]

i will do that! thx for the tip:P i was thinking about making some myself but i know that 1 or 2 will not be even and that could ruin the look:(

[SgtM]

You mods are always sick. +rep

[p0Pe]

thx man! tommorow ill go pick up the small parts for the mod and hopefully get alot of holes drilled xD and im gonna get the very last laserparts i hope:) hose manegement;) will look awsome:D

[The boy 4rm oz]

Excellent news. Can't wait to see how those last laser cut parts look.

[DonT-FeaR]

cool i like this project alot

[p0Pe]

thx!
i worked on the wholes for the resevoirs today:O and DAMN... this is the first and last time i mod a antec case! this is quality made and damn hard to drill in! 5 mm hard plastic on the top and 1 - 1.5 mm alu underneath... went out of dremel tools:( so have to buy some tommorow.. didnt get the change today as i was stupid enough to forget my visa card -.-

but i can show you this:) a teaser of the new parts that will organize the hoses:D

http://tosed.dk/billeder/DnA/Unavngivet2.JPG

cu:)

[The boy 4rm oz]

As usual your sketches are top notch.

[DonT-FeaR]

cool i love this case so far

[p0Pe]

Okay, now some work on the res!

Got to make some spacers, so bought a 5 mm ID alu tube.

Tool of choice:
http://tosed.dk/billeder/DnA/DSC01512.jpg

Made a test
http://tosed.dk/billeder/DnA/DSC01513.jpg

And a little place to fill it on
http://tosed.dk/billeder/DnA/DSC01514.jpg

The result:
http://tosed.dk/billeder/DnA/DSC01515.jpg

And the wholes I cut in the top of the case. These have to be filled to fit better. Just bought some tools for that today, the others were worn down :/
http://tosed.dk/billeder/DnA/DSC01521.jpg

Fitted the thing on! And am actually quite happy with the result. Cant wait to get this painted black!
http://tosed.dk/billeder/DnA/DSC01517.jpg

Some of the spacers is a little off, and will fix these
http://tosed.dk/billeder/DnA/DSC01518.jpg

And a little teaser of the raddy cover plate with fans on ;P
http://tosed.dk/billeder/DnA/DSC01516.jpg

And some random parts
http://tosed.dk/billeder/DnA/DSC01522.jpg

The final lasercut parts will be here tomorrow I hope, and hopefully also a little package from the last sponsors;P

Until next time! enjoy

[The boy 4rm oz]

Dude now that looks sweet. Excellent work.

[DonT-FeaR]

that looks sweet keep it up

[p0Pe]

thx m8´s!

And the lord said
”Let there be light!”
And p0Pe said
“say plz”

Got my goods from matronics.dk ! and what a package!

So.. got the god ol’ soldering tools on the table “bed” and started getting the diodes on the pumps.
http://tosed.dk/billeder/DnA/DSC01523.jpg

I haven’t soldered that much so I think the result was quite good! (not much to see though but it looks good aight? :P)
http://tosed.dk/billeder/DnA/DSC01528.jpg

And light, with the flash
http://tosed.dk/billeder/DnA/DSC01524.jpg

And without!
http://tosed.dk/billeder/DnA/DSC01525.jpg

Money shot
http://tosed.dk/billeder/DnA/DSC01533.jpg

And the remote control for the light:D
http://tosed.dk/billeder/DnA/DSC01535.jpg

And the LED strips that’s gonna be the main light of the mod
http://tosed.dk/billeder/DnA/DSC01538.jpg

And the last diodes will be places here (this is the 3 mm ones) I am thinking of ordering someone in a different colour in case I get tired of black and white. And since there is 4 holes to diodes, and the remote has 4 chanals I could mix another colour in (just cant decide wich:S)
http://tosed.dk/billeder/DnA/DSC01543.jpg

[The boy 4rm oz]

White LEDs FTW mate. This is looking bloody fantastic. Can't wait for more.

[Drew]

Wow.

That thing's gonna weigh a ton.

/subscribe, looks awesome.

[Acey]

IDK which sounds suitable for this mod. "Pope on dope" or "case is dope"?
Dammit, gimme some of the leftover once you're done hahahahaha.

[p0Pe]

haha thx:D
cant wait to get the new watercooling in -.- with my current wc my cpu&gpu reachs 55C after 3 hours of supreme commander gaming :O but that was with closed windows and a damn hot room lol

[The boy 4rm oz]

For what it's cooling those temps are still better than stock lol.

[FuzzyPlushroom]

I like pOPe. pOPe is dope.

Awesome work on that watercooling setup too!

[DonT-FeaR]

lol i agree fuzzy

[p0Pe]

haha thx xD
i just rapped the light up last night. looks awsome in the dark! cant wait to get the last lasercut parts in:D

[DonT-FeaR]

lol my leds are on rigt now

[p0Pe]

we like leds;P

[The boy 4rm oz]

Can't wait to see those last laser cut parts.

[smoking_pig]

looks really good so far, i like!

[p0Pe]

My soldering skills = fail
http://tosed.dk/billeder/DnA/DSC01550.jpg

Got the last filling on the res holder done
http://tosed.dk/billeder/DnA/DSC01553.jpg

My workplace lol…
http://tosed.dk/billeder/DnA/DSC01554.jpg

And cleaned:D
http://tosed.dk/billeder/DnA/DSC01555.jpg

And as usual I messed it up after 30 mins;P
http://tosed.dk/billeder/DnA/DSC01556.jpg

Got all the wholes drilled
http://tosed.dk/billeder/DnA/DSC01557.jpg

And got the things drilled away that made the raddy a very tight fit… fits better now
http://tosed.dk/billeder/DnA/DSC01558.jpg

Looks good:D
http://tosed.dk/billeder/DnA/DSC01563.jpg

The dvd cover plate:D a damn nice fit!
http://tosed.dk/billeder/DnA/DSC01565.jpg

http://tosed.dk/billeder/DnA/DSC01566.jpg

Its hold in place by these 2 rivets in the one side
http://tosed.dk/billeder/DnA/DSC01574.jpg

The cables from the Leds. Don’t look that bad:D
http://tosed.dk/billeder/DnA/DSC01575.jpg

And got some holes drilled and tapped for the cover plate.
http://tosed.dk/billeder/DnA/DSC01581.jpg

And some more spacers:D
http://tosed.dk/billeder/DnA/DSC01584.jpg

To the cover plate hose entrance
http://tosed.dk/billeder/DnA/DSC01585.jpg

And light! Got it all rigged :D most of it:D
http://tosed.dk/billeder/DnA/DSC01587.jpg

Only one led in the res´s atm and still lights up pretty good:D
http://tosed.dk/billeder/DnA/DSC01588.jpg

Placed one of the 10 cm led strips beside the fans
http://tosed.dk/billeder/DnA/DSC01592.jpg

And looks quite good:D
http://tosed.dk/billeder/DnA/DSC01593.jpg

I almost cant wait to get the last things drilled in place. Since I got my worktable cleaned everything has been a lot easier:D

Probertly wont get my laser stuff before Monday since there is some problems with the engraving:(

[The boy 4rm oz]

Those plates look fantastic installed my friend. When you are soldering make sure the solder is touching what is getting soldered before you heat it up. I have found that this way works best because the solder instantly washes over the solder point, ideal for cables and such.

[p0Pe]

thx for the advice:D ill try that with the rest of the 3 mm leds.. got 7 left :/

[b4i7]

lookin great pope! i had a similar res design ive been working up!

[DonT-FeaR]

gotta make a mess to create

and create you did

nice work

[The boy 4rm oz]

Mate congratz on your nomination for MOTM over at Bit-Tech. You get my vote mate.

[p0Pe]

what? wtf lol! didnt even see that hahah:D
thx!

[jdbnsn]

agreed, great work so far! As for the soldering, I'm no expert but it looks to me like the contact surface might not have been hot enough. The way my Dad taught me was to hold the iron against the surface and make a bead of molten solder to rest on the surface of the iron just next to the contacts. Then, when the temp is just high enough, the contacts will "suck up" the solder and form perfectly.

[The boy 4rm oz]

Yeah that's kinda what I tried to explain in one of my previous posts.

[DonT-FeaR]

lol thats what i learnt to :)

[Acey]

You got my vote, mate. Hopefully froop dont start banging against the wall hahahahah. Wicked lighting.. spare me some? LOL

[p0Pe]

haha:P i might actually got some leds in spare;P

So… got some more laser cut parts and guess what?
Some fits, some don’t. measured once, twice and triple… hell.. I even quadro checked !

But this is what I got:

Loot
http://tosed.dk/billeder/DnA/DSC01636.jpg

Can you guess what they are going to be used to:D ill show later

Along with the small parts I had another part made, because the other one I had didn’t fit well enough. (this is one of the parts that fits to the mm.! man I love when things turns out well

http://tosed.dk/billeder/DnA/DSC01631.jpg

Got another back plate bend

http://tosed.dk/billeder/DnA/DSC01634.jpg

Put in place:

http://tosed.dk/billeder/DnA/DSC01667.jpg

And got the whole drilled for the led wire’s

http://tosed.dk/billeder/DnA/DSC01644.jpg

Now back to these:

http://tosed.dk/billeder/DnA/DSC01635.jpg

Taddaaa… got some of the hoses in place. This will look awesome with the fluid inthere!

http://tosed.dk/billeder/DnA/DSC01645.jpg

http://tosed.dk/billeder/DnA/DSC01647.jpg

This looked kinda messy:/

http://tosed.dk/billeder/DnA/DSC01648.jpg

http://tosed.dk/billeder/DnA/DSC01649.jpg

So moved it around to look like this:

http://tosed.dk/billeder/DnA/DSC01652.jpg

The hoses has to end somewhere… in this case, under the res’s xD

http://tosed.dk/billeder/DnA/DSC01655.jpg

And this is how it looks. The hdd loop is done, and is going to sit like shown in the pictures, and the gpu/cpu loop will go like, red pump (red impellar) – raddy – cpu – gpu – blue pump – res – red pump

http://tosed.dk/billeder/DnA/DSC01660.jpg

After dark

http://tosed.dk/billeder/DnA/DSC01661.jpg

http://tosed.dk/billeder/DnA/DSC01663.jpg

Notice the little feature in the side of the front:P

http://tosed.dk/billeder/DnA/DSC01664.jpg

Duo to this xD put another light in front. It looks awesome in the dark when the front is opened and closed!

http://tosed.dk/billeder/DnA/DSC01665.jpg

thats about it! next up is paint xD... and some more parts.. when i get the last friggin parts remeasured 20 times to be sure... dont get it, they should fit:D

cu until next time lads!

[DonT-FeaR]

looks great... that case is truley huge nice modding work pope keep it up

[The boy 4rm oz]

Love how your routing the tubing mate, looks fantastic. Lighting is looking great. Shame about the bits that don't fit.

[p0Pe]

thx:D the hose routing was also something that took me a while to figure out xD

Paint… paint paint paint:D

http://tosed.dk/billeder/DnA/DSC01671.jpg

Managed to paint the test plate somehow reasonable and continued with the rest. A flie ruined one of the plates sadly:( so have to redo that one…

But that said it looks quite good

http://tosed.dk/billeder/DnA/DSC01673.jpg

And now to put it in place and see how it looks

http://tosed.dk/billeder/DnA/DSC01704.jpg

http://tosed.dk/billeder/DnA/DSC01705.jpg

Wuhuu:D

http://tosed.dk/billeder/DnA/DSC01735.jpg

And another cover plate I also got painted

http://tosed.dk/billeder/DnA/DSC01741.jpg

And got these painted ;P

http://tosed.dk/billeder/DnA/DSC01713.jpg

http://tosed.dk/billeder/DnA/DSC01716.jpg

So… lets see how they fit and look!
Oh damn! With fluid and light this will be epic!

http://tosed.dk/billeder/DnA/DSC01718.jpg

http://tosed.dk/billeder/DnA/DSC01723.jpg

http://tosed.dk/billeder/DnA/DSC01724.jpg

The bottom plate looks kinda wird, but that’s because the paint hadn’t dryid probertly. And its getting another layer or 2.

http://tosed.dk/billeder/DnA/DSC01738.jpg

And with the raddy on!:D

http://tosed.dk/billeder/DnA/DSC01737.jpg


thats about all until i get the last parts painted and when they dry i can start assembling it:D

until then! - cu

[The boy 4rm oz]

This is looking fantastic my friend. Painted bits look great and so does the tubing mounts.

[DonT-FeaR]

i agree with tb4o man looks sensational.... cant spell but i tried

[p0Pe]

thx:D

now THIS is the result i wanted:D

http://tosed.dk/billeder/DnA/DSC01743.jpg:twisted:

[FrooP]

Whaaaa Ghosts :o

[p0Pe]

mwuharharhra!!!

[DonT-FeaR]

you posed... lol nice work

[Karbon Killa]

Looks great. I love the honeycomb fan grille. And that loop looks amazing in my honest opinion.

[p0Pe]

thx! just started painted some of the smaller parts.. takes forever:( ill maybe update later:D

[p0Pe]

finally an updata again ay?:D a small one, and not with all the little parts ive done in all this time, but time is short and ive torn apart the main pc so that i could put it into the case itself!

i got the last parts home, and sanded and painted them and fitted them on! and what a job.. took me whole day -.-

to start with! DnA !:D it looks awsome IMO!
http://tosed.dk/billeder/DnA/IM005069 (Large).JPG

and got the plates fitted on! wuuuh
http://tosed.dk/billeder/DnA/IM005070 (Large).JPG

http://tosed.dk/billeder/DnA/IM005071 (Large).JPG

and how much you can see through the window
http://tosed.dk/billeder/DnA/IM005073 (Large).JPG

http://tosed.dk/billeder/DnA/IM005074 (Large).JPG

look at the raddy reflecting in the paint:P
http://tosed.dk/billeder/DnA/IM005075 (Large).JPG

and last, i got handles installed:) quite usefull since this thing already weighs a tonne!
http://tosed.dk/billeder/DnA/IM005077[/url] (Large).JPG

sry for the lack of pics, and the crappy pic quality. i am hoping to get my hand on a decent camera in a week or so, but until then you have to settle with this:D

next up is routing hoses and finishing the light setup. i got some cool bouble lights that i have a plan with.

have fun!

-p0Pe

[The boy 4rm oz]

That looks amazing, fantastic work my friend. Can't wait to see it finished.

[mittelmeier]

Looking great. Can't wait to see more.

[DonT-FeaR]

love it.... plain and simple.... love it

(the case is anything but plain and simple)

[p0Pe]

That looks amazing, fantastic work my friend. Can't wait to see it finished.

me neither:D think i might have some time to work on the watercooling today:D


Looking great. Can't wait to see more.

thx:) neither can i;P


love it.... plain and simple.... love it

(the case is anything but plain and simple)

hah yeah:P this case is a b###h to mod! but i hope the result will come out nice:P

[DonT-FeaR]

they are.... trust me.... (results)

[SXRguyinMA]

amazing work! cant wait to see more

[p0Pe]

a quick update with hose routing:D

http://tosed.dk/billeder/DnA/IM005079.JPG

i might have more in a little while;P

[p0Pe]

and another!

so... i got all the light installed + i installed 2 bouble ccf.
and i installed the remote control8):up:

so, solderd on wich took me a while and then hocked it all up, and guess what?
IT WORKS LIKE A CHARM! cant tell you how absolutely awsome this remote is:D 4 chans!
chan 1 - bouble ccf
chan 2 - res & pump leds
chan 3 - led strips front and inside
chan 4 - free

and ofc, i took some pics but they dosnt really do the mod justice:(as always it looks so much better IRL.

the remote:
http://tosed.dk/billeder/DnA/DSC01885.JPG

and the bouble light
http://tosed.dk/billeder/DnA/DSC01816.JPG

http://tosed.dk/billeder/DnA/DSC01887.JPG

the res & pump leds:
http://tosed.dk/billeder/DnA/DSC01888.JPG

http://tosed.dk/billeder/DnA/DSC01889.JPG

http://tosed.dk/billeder/DnA/DSC01894.JPG

the main light led strips:
http://tosed.dk/billeder/DnA/DSC01891.JPG

http://tosed.dk/billeder/DnA/DSC01892.JPG

http://tosed.dk/billeder/DnA/DSC01895.JPG

and a with & without flash:D

with

http://tosed.dk/billeder/DnA/DSC01898.JPG

without!

http://tosed.dk/billeder/DnA/DSC01897.JPG

i am very satisfyid with the light results! came out better than i hoped for.

more hose routing:

http://tosed.dk/billeder/DnA/DSC01899.JPG

http://tosed.dk/billeder/DnA/DSC01900.JPG

and the messe backplate that will be hidden by the side, and thank god for that;P

http://tosed.dk/billeder/DnA/DSC01901.JPG


thx for watching and reading:)

-p0Pe

[The boy 4rm oz]

Looking way cool mate, water loop is looking really good. I love black with white LEDs, my next major mod will incorporate both lol. Looks like cable management is gonna be fard for you mate lol, good luck.

[DonT-FeaR]

only thing i can suggest is have channel 4 for the on switch?? other than that.. i love it man very nice..

[p0Pe]

Looking way cool mate, water loop is looking really good. I love black with white LEDs, my next major mod will incorporate both lol. Looks like cable management is gonna be fard for you mate lol, good luck.

hah thx! as said i think the black and white fluid will be a neat combo;P


only thing i can suggest is have channel 4 for the on switch?? other than that.. i love it man very nice..

heh.. i actually thought about that and was quite hyped. then i came to think of it and the answer is: i cant
the controller runs on a 12 volt line from the psu:P wich requires to be off before it can be turned on:D off equals no power to the remote xDDDDDDD

[mittelmeier]

That looks awesome all lit up. Can't wait to see it with the fluid in the lines, it's gonna look amazing. Using one of the 4 channel remotes is a cool idea. I've always wanted to get one but I've never had anything to justify setting it up on, I may have to do that to my computer.

[p0Pe]

thx:D i only need one little hose to complete the hdd loop:( the hose i had wasnt long enough sadly!:/ gonna order it sometime next week...
next plans is to get the psu´s inthere. have to drill out the rivets in the bottom beacuse i covered the entrance whole in the deviding section with the alu plates:P (the p190 has 2 psu that stands, and they have to be put in in some obscure way)

i might have some more light pics ill put in later:D just for the fun of eye candy;P

[p0Pe]

so.. threw the black mesh window on again beacuse it fitted the theme better than the black acryllic window i planned (and the window wasnt as cool as intended -.-)

glory shots:

http://tosed.dk/billeder/DnA/DSC01912.JPG

http://tosed.dk/billeder/DnA/DSC01913.JPG

http://tosed.dk/billeder/DnA/DSC01918.JPG

http://tosed.dk/billeder/DnA/DSC01920.JPG

http://tosed.dk/billeder/DnA/DSC01923.JPG

http://tosed.dk/billeder/DnA/DSC01927.JPG

http://tosed.dk/billeder/DnA/DSC01929.JPG

and ooh i like it;P spend 15 min in bed in the total dark last nigh and played with the remote controlled light:D i dont think ill ever get tired of that xDD

until next time: :banana:

[rendermandan]

Very nice.

[p0Pe]

Very nice.

hehe:P a true man of few words xD thx!

[jdbnsn]

Looks hot pope, very clean build!

[mittelmeier]

The mesh looks nice in the window. Good choice.

[p0Pe]

Looks hot pope, very clean build!

thx alot jon:) that was also the main point of this mod:D your comment means i havent failed hard!;P


The mesh looks nice in the window. Good choice.

thx:) i also decided to put a dust filter to cover it. i got 2*140 mm fans and a 120mm on the outtake, and only a 120mm intake, so there will be pulled alot of air through that window! and i really wouldnt want the whole thing to be covered in dust:/

[The boy 4rm oz]

Dude looks fantastic, you have done a fantastic job. The accent lighting is really effective. So how much does it weigh now lol. +rep buddy, nice work.

[p0Pe]

Dude looks fantastic, you have done a fantastic job. The accent lighting is really effective. So how much does it weigh now lol. +rep buddy, nice work.

thx man!:D

atm with all panels & radiator on it weighs.... erm... (31 kilo)lol:dead::dead::dead:

[Mach]

Phenomenal attention to detail. Very nice! +rep

[p0Pe]

Phenomenal attention to detail. Very nice! +rep

thank you very much:)

so... i think i figured out what to do with the last remote channel.

fans!

only problem is that i arent actually sure if the controller puts out enough power to run all the fans
2*200 mm
2*140 mm
3*120 mm
(yeah... lots of fans lol...)

actually i hocked all the fans up to a spare psu together with the light last night, and DAMN they throw some air out of the case @ max! and makes about the same noise as a jet:P
but when turned to medium or low speed, the whole case is actually very silent! still, it would be awsome to could turn off all fans beside the ones in the psu´s:P

[The boy 4rm oz]

I dunno if you could use the controller to mount the fans. However I do have an idea for you to contemplate.

I was thinking you could install one of those Scythe fan controllers to the top of the case. After having a look at the pics you are very pressed for room there. However you could mount a fan controller above the reservoir (in one of the empty drive bays) if you can find a fan controller than can control 7 fans lol.

[p0Pe]

I dunno if you could use the controller to mount the fans. However I do have an idea for you to contemplate.

I was thinking you could install one of those Scythe fan controllers to the top of the case. After having a look at the pics you are very pressed for room there. However you could mount a fan controller above the reservoir (in one of the empty drive bays) if you can find a fan controller than can control 7 fans lol.

would be a good idea. but as it is now, there isnt room for anything underneath the resevoirs:D the hoses inthere takes up 2 5.25 drive slots -.-

all i really needed was to turn off the fans if posible since all of the antec fans comes with a standard of 3 settings, low, med, high. and dont really give any noise at the low setting:P but a almost passive pc of this size would be neat:D

[The boy 4rm oz]

Yeah I know what you mean. I use those Antecs and they are great fans. The 3 speed switch is really good. I leave mine on medium the whole time.

[p0Pe]

i think i will have mine on low or off:P no point in having them on medium or full blow wit that radiator lol... only thing i might get concerned about is the mosfet/chipset:/ i cant find any waterblocks for the board im using:( an asus m3a32 mvp deluxe

[The boy 4rm oz]

Why but the blocks when you can make em ;) lol. Doesn't one of your friends have access to a CNC?

[p0Pe]

yeah... 3 axix router, steel printer, laser & plasma cutter etc etc:P but i only know how to draw .cad´s for the 2d laser cutter :/ the other stuff is quite dificult:D

[p0Pe]

okay, the leds are using a total of 320 mA and the light controller handles 25 A ? how much does fans use:?:?:?

[The boy 4rm oz]

No idea lol. Does it say on the backing sticker or the manufacturer home page?

[p0Pe]

mach helped me with the amp question:D so know all of the fans (beside the one in the psu section) are connected to the switch and it works perfectly fine! i noticed that the led light turned a tiny bit down when i starts the fans, but that might have something to do with the low end test powersupply i uses to test it with:P either case it dosnt really matter since its so little lol.

[The boy 4rm oz]

I want pics!!! lol.

[p0Pe]

your more likely gonna need a video:P borrowed my gf´s cam but forgot it at here place -.- so your have to wait a little while:D also i need some more paint for the huge fan cover on the radiator. decided to paint that as well:D

[p0Pe]

now... 1200 Watts of cable organizing... took me quite a while lucky the 550W psu is 50% modular:D

ill let the immages talk

http://tosed.dk/billeder/DnA/PA040182.JPG

http://tosed.dk/billeder/DnA/PA040188.JPG

http://tosed.dk/billeder/DnA/PA040193.JPG

dont wory, the back plate has PLENTY of room to fit!
http://tosed.dk/billeder/DnA/PA040195.JPG

have in mind that this system contains:

2*psu´s (550&650)
4*sata drives
1*sata dvd drive
2*200 mm fans
2*140 mm fans
3*120 mm fans
1*remote controller
3*pumps

mobo, gfx & and lights

water loops contains no less than

2*res
3*pumps
4*waterblocks
2*radiators (9*120&1*120)

all in all i think its a pritty big system that almost looks like it isnt hoocked up at all:D

only thing to do know is to do the last hose routing, and connect the on off swithc!

[The boy 4rm oz]

OMG you hid a lot behind the mobo tray lol. Nice work, very clean.

[p0Pe]

thx man!

got a very big thing done tonight! filled the loop!

and... i f####d up.. the cpu block has a inlet and outlet.. guess what i misplaced?... yeah.. thats right.. got the loop filled and turned on the pump and a wierd sound came from the cpu block..
nothing else to do than to whine about my missery to a few people and then drain the loop, and start over:P luckyli it didnt took to long! so within no time i had the loop up and running again to discover ONE thing

2*18Watts pumps might be a tiny overkill:/

so i just ordered 2 koolance pump controllers, since the pumps are waaaayyy to strong:P

but. here we go with some pics:) theres alot since i just fired away with the cam:D there seems to be alot of dust on the mod lol... have to get on it with some cleaner;P

http://tosed.dk/billeder/DnA/PA060219.JPG

http://tosed.dk/billeder/DnA/PA060220.JPG

http://tosed.dk/billeder/DnA/PA060221.JPG

http://tosed.dk/billeder/DnA/PA060223.JPG

http://tosed.dk/billeder/DnA/PA060225.JPG

http://tosed.dk/billeder/DnA/PA060229.JPG

http://tosed.dk/billeder/DnA/PA060232.JPG

http://tosed.dk/billeder/DnA/PA060236.JPG

http://tosed.dk/billeder/DnA/PA060240.JPG

http://tosed.dk/billeder/DnA/PA070222.JPG

http://tosed.dk/billeder/DnA/PA070225.JPG

http://tosed.dk/billeder/DnA/PA070227.JPG

http://tosed.dk/billeder/DnA/PA070230.JPG

http://tosed.dk/billeder/DnA/PA070231.JPG

http://tosed.dk/billeder/DnA/PA070232.JPG

http://tosed.dk/billeder/DnA/PA070236.JPG

http://tosed.dk/billeder/DnA/PA070237.JPG

http://tosed.dk/billeder/DnA/PA070238.JPG

thats all fokes:D hope you like what you see!

next up is... getting theese pump controllers in place so that the pumps arent trying to create a tsunami or something... and then get all the air out..

and not to forget:D complete the hdd loop!
as it stands right now i can actually just plug it in and start the BEAST up!.. but i want to leak test it for a few hours before i do so;P

have fun lads!

[mittelmeier]

That looks sick with the black fluid in there. Great job. +rep

[TheMainMan]

So not only am I jealous of the very slick system and phenomenal build quality but also I'm jealous of the Lego Millenium Falcon under the table. They're hard to find these days at a reasonable price. The black fluid is a stunning effect.

[The boy 4rm oz]

The black coolant really sets the water cooling off mate. A very good outcome to a fantastic mod. I can't wait to see those pump controllers.

[p0Pe]

That looks sick with the black fluid in there. Great job. +rep

thx:D im quite satisfied with the koolance myself to! ill recommend it indeed xD


So not only am I jealous of the very slick system and phenomenal build quality but also I'm jealous of the Lego Millenium Falcon under the table. They're hard to find these days at a reasonable price. The black fluid is a stunning effect.

haha:D thanks alot.. and yeah.. its one of a kind:P they released a newer model but its just a cheap knockoff.. all the new models are:D


The black coolant really sets the water cooling off mate. A very good outcome to a fantastic mod. I can't wait to see those pump controllers.

pump controllers are ordred:D should be here the day after tommorow!


this is the punks:

http://www.koolance.com/water-cooling/images/more/pcb-pwm10p_p0.jpg

http://www.koolance.com/water-cooling/product_info.php?products_id=324

and a few extra hoses and some other stuff that i just need to complete this beast:D

[p0Pe]

just got the beast turned on for a little while:D couldnt resist!

now how many inhere can brag about having a 190Watt quad core running passive cooled along with a 200W gfx at a temp of 30C ;P
idle though! but still nice:D gonna have full temp scheme up when i get the pump controllers in

until then! cu:D

[The boy 4rm oz]

Dame that's a nice temp running passive mate.

[p0Pe]

Dame that's a nice temp running passive mate.

thx! i got the beast up again this night and am running on it atm!

did some temp tests

NOTICE that theese tests is with one pump running and no hdd cooling yet.

http://tosed.dk/billeder/DnA/dna temp test.JPG

sadly i couldnt get the cpu under 31C :( but the second pump might help on that:P and if i took it down to stock speed it definetly would get it under i think:D

its currently running @ 2.8

imho its some nice temps:D but cant wait to see what they will end up with when all of the boubles is out of the system and with both pumps!

[DonT-FeaR]

wow...

[AMD_TaT3rs]

i dont get it why you did all that work and then just covered it up with that side panel. if i were you i would put a big ole window right there. i dont know if you planned to do that or not but it looks good. +rep.

[The boy 4rm oz]

That is some really good temps, even as passive. Personally I would just keep the fans running at low or medium permanently.

[p0Pe]

wow...

hehe;P just wait until i get the other 2 pumps running!:D


i dont get it why you did all that work and then just covered it up with that side panel. if i were you i would put a big ole window right there. i dont know if you planned to do that or not but it looks good. +rep.

thx man:) i didnt make a helluva big side window beacuse with my old mod i got tired of being able so see everything. i think its more stylish to have a little side window and that you have to get close to really see whats inside. the light and 2 res´s alone will attrack that attention, so that people would wanna come and have a closer look:) they are gonna think that it looks good on the outside, but if they look through the window, or i take the side panel of they are gonna go "wow" ;P


That is some really good temps, even as passive. Personally I would just keep the fans running at low or medium permanently.

well... its gonna end up like this:

140 and 120 mm fans at top and back are gonna be controlled by remote since they are the noisiest
200 mm fans on raddy are gonna run on low permanently
the 120 mm fan for the hdd radiator is also gonna run permenently to get a little air flow into the case. not much is needed since the passive cooled chipset really is the only beaf.

and with 200 mm fans running along with the other 2 120 mm thats gonna be permenetly (the other is the one in the psu section) the whole thing is as good as silent:P and i love it! just hope that the pump regulators will reduce the noice from the pump... im not that worried about preasure drop since its 2 18Watt´s pumps lol...
only think im not sure of at this moment is how much the xspc bay pump noises... but ill see soon;P


EDIT:

ill have the pump regulators tommorow, and then i will have the change of bleeding the system completely!
also i set some money aside for a new part i am dreaming:yellow: of

[AMD_TaT3rs]

hmm thats an interesting reason. i would have at least changed the mesh into plexi or something. also what are your other plans?

[p0Pe]

well.. i tryid to put black acryllic on the side window, but it didnt look that good... the mesh is giving a better finish:)

did a test run last night. check theese temps out;)
http://tosed.dk/billeder/DnA/max temp test4.JPG

and i got about 52C passive on both cpu and gpu:D

[Acey]

Slick as hell mate. Especially the coolant. Turning out real classy and clean. +rep!

[DonT-FeaR]

yea i personially love the 2 coolant lots..... very.... unique? is that a good word to describe its awsomeness?

[The boy 4rm oz]

yea i personially love the 2 coolant lots..... very.... unique? is that a good word to describe its awsomeness?

Unique and smart. Won't be draining the wrong loop by accident lol.

[walterbieber]

That!!!! Is One Of My Favorite Mods. You Have Great Computer There. It's So Simple, Elegant And Great Looking (Sounds Like A Girl Were Talking About lol). Keep Up The Good Work I Might Do The Same With My Mod. Cover Up All The Things (Disk Drives And Things) How Would You Get The BLACK Colored Coolent?

[p0Pe]

Slick as hell mate. Especially the coolant. Turning out real classy and clean. +rep!

thx man:D


yea i personially love the 2 coolant lots..... very.... unique? is that a good word to describe its awsomeness?

just wait till i get the last coolance into the system:D tommorrow, or the day after that! then semi final pics are up!


That!!!! Is One Of My Favorite Mods. You Have Great Computer There. It's So Simple, Elegant And Great Looking (Sounds Like A Girl Were Talking About lol). Keep Up The Good Work I Might Do The Same With My Mod. Cover Up All The Things (Disk Drives And Things) How Would You Get The BLACK Colored Coolent?

wow, thanks:D

the coolant is "feeser-one" :) easy to find, easy to use:D and works like a charm! its nice as he## and dosnt fry your hardware if leaked

i apriciate all of your comments and you all helped me get through this mod!
i can say its running like a dream! cpu temps is 31C idle atm! and have been all day:D all at low xD probertly beacuse i got the loop drained for air! so now the pumps are running more silent, and effecient:banana::up:

[The boy 4rm oz]

WOOHOO, nice temps mate.

[DonT-FeaR]

wow...
thats nice...
think mine ran at about 35 stock in my soprano

[mittelmeier]

Those temps look great. I can't wait to see the other cooling loop hooked up.

[p0Pe]

Hoses Should be here today! So when i get home from work i will put the last loop together:D

[The boy 4rm oz]

Awesome, can't wait for pics.

[DonT-FeaR]

yea this will be sweet!!!

[p0Pe]

So i hope:D but i just got told that the lightning just hit near our house and whiped out all power... And the pc was on:/ i hope the psu's can handle that:D it would suck to get home to hardware grill xD
I will have pics up tonight i think:D cant wait to see the last loop:D ! And just got confirmed that the Hoses Has arrived:) so now its almost done.

[The boy 4rm oz]

Lol yeah I hate lightning. we always get it near our place. My Antec Neo has taken a fair few close strikes and power outs and is still strong. Your PC should be fine.

[p0Pe]

Yeah:D lets hope so lol... Just hope to hit the 30 c on the harddrives with the watercooling:D

[The boy 4rm oz]

30*c with water, they should get lower than that. Mine sits at about 34*c with a single fan blowing over it.

[p0Pe]

yeah. but mine is a 4*hdd cluster in tight space, and in the same compartment at the two psu´s xD right now they are about 27/30 cus i just turned the beast on, but after a few hours they are on the 40C ca. :)
hell my cpu is idling @ 32 now lol... with only the raddy fans on low

[Acey]

Careful, froop might go green again hehehehehehe

[p0Pe]

not tonight :( ffs im mad! "yeee yeee we have a package for you yeee yeee" and when home no FUC#ING package!!! guess i have to wait for tommorow -.- should have had the friggin thing last monday....

[FrooP]

Careful, froop might go green again hehehehehehe


say WHAT?

[mittelmeier]

I know how you feel about the mail, but there is always tomorrow.

[p0Pe]

got the hose... finally! now i just have to get home and get the last loop together:D

[The boy 4rm oz]

Great news mate. I can't wait to see that second loop up and running.

[p0Pe]

and your gonna get it! not as cool as i hoped though.. the pics dosnt do the loop justice since the water in the res looks AAAWSOME with the light in dark!!!

this is the res with the clear water up to about half. i messed filling the loop and dropped some fluid so i didnt have enough to fill it:( gotta order another L :/ but its only 30$ soooo...
http://tosed.dk/billeder/DnA/PA170252.jpg

and the pump bay thingie
http://tosed.dk/billeder/DnA/PA170254.jpg

with led light
http://tosed.dk/billeder/DnA/PA170258.jpg

black & white!
http://tosed.dk/billeder/DnA/PA170260.jpg

not the sharpest pics.. but it will do:P
http://tosed.dk/billeder/DnA/PA170270.jpg

http://tosed.dk/billeder/DnA/PA170272.jpg

http://tosed.dk/billeder/DnA/PA170277.jpg

i personally like this one
http://tosed.dk/billeder/DnA/PA170279.jpg

and this one
http://tosed.dk/billeder/DnA/PA170280.jpg

erm.. and this one lol
http://tosed.dk/billeder/DnA/PA170282.jpg

okay... i like most of them:
http://tosed.dk/billeder/DnA/PA170287.jpg

the gfx
http://tosed.dk/billeder/DnA/PA170289.jpg

and the res´s again. its hard to get a prober shot with this light source -.-

http://tosed.dk/billeder/DnA/PA170253.jpg


proper shot of the whole loop
http://tosed.dk/billeder/DnA/PA170257.jpg

the pump controllers:
http://tosed.dk/billeder/DnA/PA170260.jpg

and another few eye candy shots

http://tosed.dk/billeder/DnA/PA170262.jpg
a shame that tygon have to put numbers all over their tubes:( it totally destroys the last touch! curse them

the awsomemememe pumps! i turned them down to lowest speed and they are decent quiet... (everyone who has a ddc pump knows the noise they can make at full blow:P)
http://tosed.dk/billeder/DnA/PA170268.jpg

so.. there you had it:) now all thats left to do is fixing the radiator fan cover... i have bend it and such but its just hanging on the side for now. need to paint it, and maybe put some light under the "DnA" logo.

enjoy, and have a nice weekend;P

[The boy 4rm oz]

I forget, what does the clear loop cool? or is it just for decoration?Looks fantastic mate. The white and black goes really well together.

[DonT-FeaR]

yeah thats sweet..... nice work man...

[p0Pe]

the clear loop cools the harddrives:P temp on hdd´s is down by 7/8 C. decent for a pump that size and a 120 mm raddy.

and thank you veddy much:D

[mittelmeier]

Those pics look amazing. I wish I could see that in real life because it's gotta look twice as good. +rep

[ContraptionMaker]

Hey pOPe! Just got a chance to check out your puter and awesome job on the wc'ing and cable management! The whole thing looks fantastic! Props & of course +rep

[p0Pe]

Those pics look amazing. I wish I could see that in real life because it's gotta look twice as good. +rep

yeah, it really does:P but most mods do:D and thx alot!


Hey pOPe! Just got a chance to check out your puter and awesome job on the wc'ing and cable management! The whole thing looks fantastic! Props & of course +rep

thx for reading:P and the cable manegement was one of the things i just wanted to do perfect! i cant stand comps with cables everywhere:D amazing what you can do with a little patience:twisted:

well... as i turned off the pc yesterday, the last water in the hdd res just went down to the pump, so now there is excactly not enough fluid to make the thing run -.- .. so i have to order another L for like.. only fill up the res lol...

i might order someting else while im at it:D just got my hands on some cash i didnt expected :up:

[DonT-FeaR]

it looks killer man.... like they said... nice cable managment and w/c loops..

[p0Pe]

Thx:D i just used a bunch of money on a new monitor. It was that or a new gfx:D and i got some more clear fluid but thats gonna take a few days:(

[The boy 4rm oz]

Cool, which monitor did you get?

[p0Pe]

this little 24" sucker:smoker:
http://www.benq.com/products/LCD/?product=1313

http://www.markpascua.com/wp-content/benq-v2400w-1.jpg

[DonT-FeaR]

nice :) very cool.... updates?

[The boy 4rm oz]

Nice monitor mate, I was looking at that one. I like the unusual stand. Makes the monitor seem bigger than it really is.

[p0Pe]

yeah. its a nice monitor indeed.
i dont know when next updates will be sadly:/ things are going a bit slow lol

[p0Pe]

okay! a small update.

the reason that this mod has been on stand by for a while was beacuse the reservoirs leaked:( sadly...
it went so bad that fluid was going in between the plastik and the metal on the top, so had to find new reservoirs... only problem, they had to be 60mm in diamiter to fit in. and such reservoirs is hard to find
asked xspc if they could make costum reservoirs but sadly no.

so only thing to do:
1: make them myself.
2: fizzle around with some premade

i choose nr. 2

took 2 of the 150 ml xspc reservoirs and since they were 70mm in diamiter i had to cut away some. but only so they just fitted into the top whole:

http://tosed.dk/billeder/DnA/Unavngiv23et.JPG

so i went ahead and killed the little buggers!

http://tosed.dk/billeder/DnA/IMG_0063.jpg

dismantle the old ones:( i loved them:( but cant use something that leaks -.- i thought about buyin a pair of new ones, but i just dont think that they can manage the preasure and passive temps, which i want to play a bit with :/

http://tosed.dk/billeder/DnA/IMG_0066.jpg

and here to show the leaky part:

http://tosed.dk/billeder/DnA/IMG_0067.jpg

http://tosed.dk/billeder/DnA/IMG_0070.jpg

and how it fitted (with a little violence with the dremel)

http://tosed.dk/billeder/DnA/IMG_0071.jpg

one down another one to go

http://tosed.dk/billeder/DnA/IMG_0072.jpg

im probertly gonna end up doing a litle cover plater to make a smoother "edge" between the res and the case top

with modyfied top (originally to wide)

http://tosed.dk/billeder/DnA/IMG_0073.jpg

light from the blue bouble light (think this is gonna look cool in the dark:D)

http://tosed.dk/billeder/DnA/IMG_0074.jpg

http://tosed.dk/billeder/DnA/IMG_0077.jpg

note that in theese pics fluid already has been filled in

so how its gonna look compared to the old. a big bigger and not transparrent but... ill survive.
and its alu i know, but i hope to be alright with the amount of anti corrosion fluid thats in lol

http://tosed.dk/billeder/DnA/IMG_0083.jpg

i dont know when ill have the time to do the other one, but for now:

marry christmas and happy new year!
:santa: :santa: :santa: :santa: :santa: :santa:

[The boy 4rm oz]

Man that really sucks about your reservoirs leaking. The new ones look great though, a worthy replacement.

[p0Pe]

thx man! :) yeah.. they were the only one i thought went good with the case. they are to high sadly:/ but they cant get any lower:D

[The boy 4rm oz]

Passive reservoirs for a passive cooled case lol.

[p0Pe]

So.. a small update.
Its been a while but ive had a thing or two between my hands :D (or on my feets should i say…)
Rules are made to be broken lol
http://tosed.dk/billeder/DnA/CIMG0423.jpg

That’s me, with the baby size ski´s
http://tosed.dk/billeder/DnA/CIMG0427.jpg

For some reason this route was closed and called “the murderer” we had to find out why… took us an hour to get to the bottom of the valley xD on normal routes we could run that trip in 5 min.
http://tosed.dk/billeder/DnA/CIMG0625.jpg

Well.. on to the mod!

As you can see I already installed one of the new reservoirs. And I did not have the time to start on the other one since I knew it was going to be a b#tch to install
http://tosed.dk/billeder/DnA/CIMG0945.jpg

Had to take the back plate of again. What a mess:/
http://tosed.dk/billeder/DnA/CIMG0946.jpg

Note the bracket I used to keep the wires in the hole made for them to slip through xD the little whole all the sata cables are going through is the one that’s barely visible on the other side.
http://tosed.dk/billeder/DnA/CIMG0950.jpg

This is the space I have to work with :/
http://tosed.dk/billeder/DnA/CIMG0963.jpg

Now this little thing is going to be hard to get out xD
http://tosed.dk/billeder/DnA/CIMG0969.jpg

“working it”
http://tosed.dk/billeder/DnA/CIMG0980.jpg

And as usual the watergods didn’t thought nice of me, so on of my fittings went mental.. but I don’t belive in gods so on with it
http://tosed.dk/billeder/DnA/CIMG0981.jpg

And a little neat feature I made on the raddy fan cover;)
http://tosed.dk/billeder/DnA/CIMG0984.jpg

And a very very bad pic of how it turned out. I have a few plans on how to make a smooth erm… “melting”? between the res´s and the top. But that’s gonna be later:D
http://tosed.dk/billeder/DnA/CIMG0978.jpg

I have talked with one of my friends about getting some nicer foto´s of the whole case, (he´s a camera geek) so I hope to get some better pics up soon:D

Don’t know how much I will be able to work on the case the next amount of time though… my car just broke and at the same time some sh#t f#ckers decided to break the rear and front window and steal my sound system:( but life goes on:D

Ill cu!
Comments and stuff are as always greatly appreciated!

-p0Pe

[Kumo]

Cool rez's idea

[p0Pe]

thx:) though i liked the other ones better, but ill make theese work:D

[Kumo]

The other one were different, but nice too. Maybe you could re-use them in another mod, if fix the leakages.

New ones have... i don't know... gear feeling :D

[p0Pe]

The other one were different, but nice too. Maybe you could re-use them in another mod, if fix the leakages.

New ones have... i don't know... gear feeling :D

hah.. never thought of it that way:D
dont think ill be able to fix the leakages in the others res´s though... might be able to get them swapped at my sponsor if i ask nice lol

[DonT-FeaR]

LEGEND!!! lol zac and i break the law with our bikes all the time

[p0Pe]

a little teaser on the sponsor plate:

http://tosed.dk/billeder/DnA/CIMG1019.jpg

http://tosed.dk/billeder/DnA/CIMG1024.jpg

this is not the final version though

[The boy 4rm oz]

The plate looks very classy.

[p0Pe]

thx man:)

a update, sort of... got tired of the old desk and got myself one from work! you dont belive what they threw out :S

old desk:

http://tosed.dk/billeder/DnA/CIMG1030.jpg

and 5 min after then WRUAM! and the nuclear vacum cleaner had it torn apart!

http://tosed.dk/billeder/DnA/CIMG1031.jpg

starting to asemble the new table. look at the size of that thing :O

http://tosed.dk/billeder/DnA/CIMG1033.jpg

how high it goes,

http://tosed.dk/billeder/DnA/CIMG1036.jpg

how low,

http://tosed.dk/billeder/DnA/CIMG1037.jpg

and with the pc in place! damn there is a lot of room on this sucker xDDD

http://tosed.dk/billeder/DnA/CIMG1044.jpg

that was actually what i had to show lol...

sleep tight:D

[The boy 4rm oz]

Great desk mate. I can't believe they would throw that out haha, nice find.

[DonT-FeaR]

i think ur mod deserves some desk space... who else does ?

[Vitz¥^]

aye, very good desk.. plenty of room to spread... lol!

personally i wouldnt put it right in front of the window like that tho, you wont be able to see didly squat if the sun shines through it! lol!

[p0Pe]

Great desk mate. I can't believe they would throw that out haha, nice find.

yeah... they got way to much cash!


i think ur mod deserves some desk space... who else does ?

thx man:D and desk space it got:P


aye, very good desk.. plenty of room to spread... lol!

personally i wouldnt put it right in front of the window like that tho, you wont be able to see didly squat if the sun shines through it! lol!

sunshine? i live in denmark:P sunshines is as rare as dancing bananas:banana:

but i think that im eventually gonna do some redecorating:)

[DonT-FeaR]

oh nice!!!! dancing bananas,,,, rofl....


pics on desk space?

[rendermandan]

That is a nice desk.
-I like the sponsor plate, too, but what do you mean its not the final version?

[p0Pe]

that i "hope" that its not the final:) got a thing i like to test out. just to get it to fit into the mod better but if that fails ill have this one:D


pics on desk space?

erm.. what? :P

[The boy 4rm oz]

There is a thread running that wants you to post up pics of your desk space, where you game. I think that's what DF means.

[p0Pe]

already posted inthere i think:P

[DonT-FeaR]

nah i ment.. got pics of the pc on ur desk yet...

[p0Pe]

I tryid to take a few decent pics of the pc on the desk. On this on it actually looks quite standard except from the side window and the top res´s
http://tosed.dk/billeder/DnA/CIMG1050.jpg

And how it looks with the side panel off. I didn’t like the looks of the psu compartment, neither did I like the harddrive compartment so I decided to see what I could do about it

This was how it looked to start with
http://tosed.dk/billeder/DnA/CIMG1054.jpg

And after I worked a little with a black piece of acrylic
http://tosed.dk/billeder/DnA/CIMG1059.jpg

And gonna make another one for the hdd compartment… just have to dremel it into shape first:D
Like this:
http://tosed.dk/billeder/DnA/CIMG1060.jpg

Sooo… I wanted more light in the case as the single led strip wasn’t enough
Couldn’t find space in the case itself though:( the strips would either be to visible or to invisible!... so I mounted them on the side panel with a 3 pin fan connector so when I have to take the side panel off, I don’t have to cut it all up:P
http://tosed.dk/billeder/DnA/CIMG1066.jpg

Now I just have to get the wire that goes the remote control and find channel 2 on that one ó_ò
Luckily I remembered wich one it was;P sort of
http://tosed.dk/billeder/DnA/CIMG1067.jpg

A soldering station really eases things up lol!
http://tosed.dk/billeder/DnA/CIMG1068.jpg

Weight -.-
http://tosed.dk/billeder/DnA/CIMG1074.jpg

And some bad night shots:( I want to have some really god pictures taken soooo baaad! You cant see jack of the light on these ones:/
http://tosed.dk/billeder/DnA/CIMG1075.jpg

http://tosed.dk/billeder/DnA/CIMG1077.jpg

Okay.. this one sort of does it
http://tosed.dk/billeder/DnA/CIMG1079.jpg

http://tosed.dk/billeder/DnA/CIMG1088.jpg

And some blurry overall pics:)
http://tosed.dk/billeder/DnA/CIMG1056.jpg

http://tosed.dk/billeder/DnA/CIMG1058.jpg

http://tosed.dk/billeder/DnA/CIMG1063.jpg

Enjoy:) comments and questions is as always welcome:D

[SXRguyinMA]

looks nice :D

[Karbon Killa]

You want more lights? Why not get white LED fans? They usually are decently bright, but not too bright at the same time.

[The boy 4rm oz]

The lower compartment looks ten times better mate.

[TheMainMan]

About halfway through the pictures I love the face in CIMG1077.jpg:shoed:

[p0Pe]

looks nice :D

thx:D


You want more lights? Why not get white LED fans? They usually are decently bright, but not too bright at the same time.

beacuse i wanted to be able to turn all light off:)

as it is now, the fans is remote controlled all except the raddy fans, and the fan in the hdd and psu compartment.
and light is too, so if i put led fans inthere there would be light whenever i turn the fans on, and since the fans are covered by plates, its limited how much led fans would light up:)


The lower compartment looks ten times better mate.

thx!

and yeah:D it gives a hole other look at it!


About halfway through the pictures I love the face in CIMG1077.jpg:shoed:

haha lol xD

[Karbon Killa]

So couldn't you just take the leds from the fans, and re wire them, so that they are not being powered from the fan, and have them going to the same switch and power as the rest of your lights? I believe I've seen it done somewhere on here before, not sure where though.

[p0Pe]

i could but you have to bear in mind that i have the cover plates infront of the fans, wich tottally hides the edge of the fan, wich is where most of the light would come from from a led fan. its a great idea if i hadnt used the covers but i didnt wanted any visible fans:D

[p0Pe]

so... post number 1000. that took a long time lol.

the upcoming week will hopefully finish this mod! i got plans for engraving, foto´s and lasercutting xD gonna be busy as h#ll but it will be worth it i hope!

so on friday i will have some fotos to share:D hopefully some awsome ones;P

almost cant wait!

until then, cu lads!

[DonT-FeaR]

sweet
cu lad!! lol looking forward to this beast being complete

[p0Pe]

a little teaser. couldnt resist!

http://tosed.dk/billeder/DnA/CIMG1140s.jpg

and tommorow your in for another suprice;)

[SXRguyinMA]

nice :D

[The boy 4rm oz]

Man now that looks cool.

[DonT-FeaR]

wow time goes really slow when ur waiting for something

[rendermandan]

ok, its tomorrow, where is my suprise???? LOL

[p0Pe]

im getting the final things up for the photo shoot:) you will have your suprises within the day i promis:D (its 17:37 @ my place;) still got time:D)

thanks for the comments:) i hope i wont let you down lol xD but i can say... IMO it looks awsome ;P

[p0Pe]

lady´s and gentlemens

a few shots since i didnt have time to go trough 150 pics @ 20mb. but better might come;)

i give to you

DnA

ill let the pics speak

http://tosed.dk/billeder/DnA/Computer.JPG

http://tosed.dk/billeder/DnA/Computer_3.JPG

http://tosed.dk/billeder/DnA/Computer_2.JPG

http://tosed.dk/billeder/DnA/Computer_1.JPG

http://tosed.dk/billeder/DnA/Computer_4.JPG

for better quality click the pics;)

hope you like it:D more will come and then ill put this in the chest of finished mods!

best regards /0/

-p0Pe

[FrooP]

damn sweet

[p0Pe]

thx:D took all eveaning! cant wait to get the other pics up;)

[The boy 4rm oz]

Sweet pics mate. +rep

[Kumo]

Good work. Amazing details.

The new joint between case and rez's is nice and like the side panel with hex mesh pattern.

[SXRguyinMA]

nice! +rep

[p0Pe]

Sweet pics mate. +rep

thx:D 3.5 hours of fotografing lol


Good work. Amazing details.

The new joint between case and rez's is nice and like the side panel with hex mesh pattern.

thans! the new joint was just put on an hour before the shoot xD


nice! +rep

thanks dude!:glasses:

[DonT-FeaR]

very nice.. i like it... good on ya mate... very well made

[p0Pe]

very nice.. i like it... good on ya mate... very well made

thx:D always nice to hear:)


So fokes. This will be my final update on this mod.
It have taken its time, and had its trouble but I think it came out quite nice! I am already looking forward doing another one, with all I’ve learned on this xD.

Not much to say, so I’ll let the pictures speak for themselves. Beware, there’s going to be a bunch;)
some of the previous pics are showed one more time, but thats just to keep all the finished together:)

http://tosed.dk/billeder/DnA/Computer.JPG

http://tosed.dk/billeder/DnA/Computer_3.JPG

http://tosed.dk/billeder/DnA/Computer_2.JPG

http://tosed.dk/billeder/DnA/Computer_1.JPG

http://tosed.dk/billeder/DnA/Computer_4.JPG

http://tosed.dk/billeder/DnA/IMG_1010.jpg

http://tosed.dk/billeder/DnA/IMG_1001.jpg

http://tosed.dk/billeder/DnA/IMG_1004.jpg

http://tosed.dk/billeder/DnA/IMG_1013.jpg

http://tosed.dk/billeder/DnA/IMG_1021.jpg

http://tosed.dk/billeder/DnA/IMG_1028.jpg

http://tosed.dk/billeder/DnA/IMG_1038.jpg

http://tosed.dk/billeder/DnA/IMG_1040.jpg

http://tosed.dk/billeder/DnA/IMG_1051.jpg

http://tosed.dk/billeder/DnA/IMG_1055.jpg

http://tosed.dk/billeder/DnA/IMG_1058.jpg

http://tosed.dk/billeder/DnA/IMG_1064.jpg

http://tosed.dk/billeder/DnA/IMG_1081.jpg

http://tosed.dk/billeder/DnA/IMG_1103.jpg

http://tosed.dk/billeder/DnA/IMG_1108.jpg

http://tosed.dk/billeder/DnA/IMG_1114.jpg

http://tosed.dk/billeder/DnA/IMG_1120.jpg

http://tosed.dk/billeder/DnA/IMG_1124.jpg

http://tosed.dk/billeder/DnA/IMG_1126.jpg

http://tosed.dk/billeder/DnA/IMG_1129.jpg

http://tosed.dk/billeder/DnA/IMG_1130.jpg

Thanks to everybody who has watched, commented and helped me with this mod! As usually the world wide web has a lot to offer and so have the people behind it!

and many many thanks to my sponsors!

www.CoolBits.dk

&

www.Matronics.dk



Furthermore would I like to thank Dennis from flex skilte for the help he did in the last hours, and Bo from Skjern Fotoklub

www.flexskilte.dk

www.skjernfotoklub.dk


I herby declare this mod, finished :)

Best regards
-p0Pe

[SXRguyinMA]

love the pics :bowdown:

[DonT-FeaR]

*clap clap clap*

[chaksq]

Wow!

I must admit at first I was thinking it wasn't looking that great, seemed like some of the design ideas clashed. But the final product looks amazing. You did a great job.

[TheGreatSatan]

Awesome! +rep for sure.

[p0Pe]

love the pics :bowdown:

thx man!


*clap clap clap*

:banana:


Wow!

I must admit at first I was thinking it wasn't looking that great, seemed like some of the design ideas clashed. But the final product looks amazing. You did a great job.

thanks man. yeah, it might had looked a bit confusing at start but i think the result came out pritty good myself too:D


Awesome! +rep for sure.

thank you man:)

[msmrx57]

Awesome! +rep for sure.

What he said. :bowdown:

[jdbnsn]

Very impressive work p0Pe! That mod came out in Lamborghini-style showroom quality! You might even want to consider shooting some pics over to milliondollarpcs.com

+rep for sure bro!

[p0Pe]

What he said. :bowdown:

:bunny: thank you:D


Very impressive work p0Pe! That mod came out in Lamborghini-style showroom quality! You might even want to consider shooting some pics over to milliondollarpcs.com

+rep for sure bro!

wow thanks man:D dont think its quite good enough for that but ill give it a try;P could be cool. but i think i need some better macro foto´s if i am to get there xD

[OvRiDe]

Great work dude! And I agree with Jon, you definitely should send them some pics!

[DonT-FeaR]

i gunna check out that site now lol...

send em the photos...
what u got to loose?

[p0Pe]

yeah your right:P btw the site is:

www.million-dollar-pc.com


and once again thx all:) i might get some better macro foto´s by the end of the week ! going to a local lan to show off;P

[Mach]

Awesome work! +rep

[The boy 4rm oz]

I already nominated you mate, just like I said I would ;).

[p0Pe]

I already nominated you mate, just like I said I would ;).

thx man :O

[tomcatt]

Excellent work there !! Truly worth a million dollar pc ;)

[DonT-FeaR]

i found that site before you put the link up :) but thanks anyway

[p0Pe]

Excellent work there !! Truly worth a million dollar pc ;)

thanks a lot!:banana:
means alot:)



i found that site before you put the link up :) but thanks anyway

np man:D