Wag
06-24-2007, 03:10 AM
Hey Guys.
I've been an avid PC gamer and enthusiast for some time now and after the local gaming center folded up here (a damn shame mind you) was gifted many old and crappy cases. I've worked with my hands some and believe that anyone can do anything if they work at it. With that in mind, I set off on my first real case mod. Here is a few pictures of the starter case:
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1058.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1064.jpg
and also the front plastic bezel taken off and dissembled
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1060.jpg
Project: Dew
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1050.jpg
You guessed it, I'm doing a Mountain Dew case. Instead of actually painting the case or putting decals on it, I decided to go all out and literally cover the entire case in real, honest to god, Dew cans.
After a trip to the hardware store to buy some cheap snips, I dove right into the stockpile of cans on my counter. Finally deciding on a uniform size for the cans i shaved off the rough edges with an old school paper cutter. This helped to make straight edges for the cans to line up nicely with one another.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1055.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1070.jpg
After getting my cans cut up, I was off to begin gluing the cans to the case.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1072.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1075.jpg
I started with an automotive glue made for bonding metals, I did the removable side of the case this way. It was slow and painful going and the glue expanded and ran out the cracks between the cans wrecking any consistency I had. Even under pressure of clamps (and textbooks) the surface was not sufficiently smooth. Ultimately opted for an easier method on the rest of the case using a spray adhesive. The rest of the case was only one piece so I commenced with the gluing and fastening of the remaining cans.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1096.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1115.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1134.jpg
It was tough getting the cans to remain fastened over the edge. I used a pretty inexpensive glue and it didn't seem to matter how much pressure I used and how long it was clamped, they just didn't want to stay glued down over the edges. Also, the cans still didn't yield a smooth enough surface for my taste so I bought some thin acrylic and cut three pieces to go over the top and two sides. This secured the cans in place and provided a smooth and shiny surface for my cans.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1142.jpg
Well, that was the easy part. Now it was on to the front bezel for the case.
I rather liked the basic design of the original front but there needed to be some changes made to make it work the way I had intended. I cut out a large piece of the plastic that would get in the way of my power and reset switches, USB ports, and fan and found a piece of foam the appropriate size to stand off my new insert.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1167.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1168.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1171.jpg
I decided to buy a thin piece of sheet metal which I could then glue more cans to and also mount my buttons and ports to the front of the computer. Another piece of acrylic was cut and affixed to the sheet metal using some Chrome hex bolts.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1300.jpg
After much thought, I decided to use the original power and reset buttons.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1242.jpg
To do this i cut out the power and reset sockets from the gray insert from the front bezel and filed down the edges until I had two plastic brackets for my switches remaining. These were then mounted to the back of my sheet metal using hot glue.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1244.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1150.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1305.jpg
Finally I attached the 120mm fan to the front as well and cut my foam piece which I used as a spacer/standoff to accommodate the wires and fan.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1306.jpg
I also had to affix cans to the original front bezel as well. After several failed attempts with the spray adhesive, it was back to the automotive goo and clamping the pieces down one by one. Doing the corners was the most difficult.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1262.jpg
Since I was unable to cover the outer part of the bezel with acrylic, I polyeurthaned it instead. This worked ok, but even after about a dozen coats, still yielded only a moderately smooth surface. Since I was growing impatient, I decided that it was 'good enough." Everyone who has seen the case always asks me how I got it so smooth and I always wonder what their smokin since it didn't end up as smooth as I wanted. Oh well....
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1308.jpg
Finally the last (and probably easiest part at this point) was to do something about the unused drive bays. I simply took the original plastic parts and gluded a can to them and put a piece of acrylic over that. This is somethign that is commonly done on many commercial sold cases and was very simple.
Finally I put the last pieces and the hardware inside and took some pictures. These finished pictures were taken on my kitchen table with a tablecloth hung up behind it. Thats about as professional I get with photography. Hope you enjoyed the mod. I know I am ;-)
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1399.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1400.jpg
All of my acrylic was attached by small stove bolts. They are stainless but looked good enough to be finishing bolts. I ended up using 12 per side and six on the top.
Dew Case Specs:
AMD FX-60 DC 939
DFI LANPARTY UT nF4 SLI-DR
G.SKILL 1GB (4 x 512MB) 184-Pin DDR SDRAM DDR 550 (PC 4400)
Gefore 7900GT 256MB pcie
320 Gig Seagate Sata 3gb/s HD
500 Gig WD Caviar Sata 3gb/s HD
Thanks everyone!
Wag
I've been an avid PC gamer and enthusiast for some time now and after the local gaming center folded up here (a damn shame mind you) was gifted many old and crappy cases. I've worked with my hands some and believe that anyone can do anything if they work at it. With that in mind, I set off on my first real case mod. Here is a few pictures of the starter case:
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1058.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1064.jpg
and also the front plastic bezel taken off and dissembled
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1060.jpg
Project: Dew
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1050.jpg
You guessed it, I'm doing a Mountain Dew case. Instead of actually painting the case or putting decals on it, I decided to go all out and literally cover the entire case in real, honest to god, Dew cans.
After a trip to the hardware store to buy some cheap snips, I dove right into the stockpile of cans on my counter. Finally deciding on a uniform size for the cans i shaved off the rough edges with an old school paper cutter. This helped to make straight edges for the cans to line up nicely with one another.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1055.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1070.jpg
After getting my cans cut up, I was off to begin gluing the cans to the case.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1072.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1075.jpg
I started with an automotive glue made for bonding metals, I did the removable side of the case this way. It was slow and painful going and the glue expanded and ran out the cracks between the cans wrecking any consistency I had. Even under pressure of clamps (and textbooks) the surface was not sufficiently smooth. Ultimately opted for an easier method on the rest of the case using a spray adhesive. The rest of the case was only one piece so I commenced with the gluing and fastening of the remaining cans.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1096.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1115.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1134.jpg
It was tough getting the cans to remain fastened over the edge. I used a pretty inexpensive glue and it didn't seem to matter how much pressure I used and how long it was clamped, they just didn't want to stay glued down over the edges. Also, the cans still didn't yield a smooth enough surface for my taste so I bought some thin acrylic and cut three pieces to go over the top and two sides. This secured the cans in place and provided a smooth and shiny surface for my cans.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1142.jpg
Well, that was the easy part. Now it was on to the front bezel for the case.
I rather liked the basic design of the original front but there needed to be some changes made to make it work the way I had intended. I cut out a large piece of the plastic that would get in the way of my power and reset switches, USB ports, and fan and found a piece of foam the appropriate size to stand off my new insert.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1167.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1168.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1171.jpg
I decided to buy a thin piece of sheet metal which I could then glue more cans to and also mount my buttons and ports to the front of the computer. Another piece of acrylic was cut and affixed to the sheet metal using some Chrome hex bolts.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1300.jpg
After much thought, I decided to use the original power and reset buttons.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1242.jpg
To do this i cut out the power and reset sockets from the gray insert from the front bezel and filed down the edges until I had two plastic brackets for my switches remaining. These were then mounted to the back of my sheet metal using hot glue.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1244.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1150.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1305.jpg
Finally I attached the 120mm fan to the front as well and cut my foam piece which I used as a spacer/standoff to accommodate the wires and fan.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1306.jpg
I also had to affix cans to the original front bezel as well. After several failed attempts with the spray adhesive, it was back to the automotive goo and clamping the pieces down one by one. Doing the corners was the most difficult.
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1262.jpg
Since I was unable to cover the outer part of the bezel with acrylic, I polyeurthaned it instead. This worked ok, but even after about a dozen coats, still yielded only a moderately smooth surface. Since I was growing impatient, I decided that it was 'good enough." Everyone who has seen the case always asks me how I got it so smooth and I always wonder what their smokin since it didn't end up as smooth as I wanted. Oh well....
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1308.jpg
Finally the last (and probably easiest part at this point) was to do something about the unused drive bays. I simply took the original plastic parts and gluded a can to them and put a piece of acrylic over that. This is somethign that is commonly done on many commercial sold cases and was very simple.
Finally I put the last pieces and the hardware inside and took some pictures. These finished pictures were taken on my kitchen table with a tablecloth hung up behind it. Thats about as professional I get with photography. Hope you enjoyed the mod. I know I am ;-)
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1399.jpg
http://www.ghostobservance.com/uploads/Images/dewcase/IMG_1400.jpg
All of my acrylic was attached by small stove bolts. They are stainless but looked good enough to be finishing bolts. I ended up using 12 per side and six on the top.
Dew Case Specs:
AMD FX-60 DC 939
DFI LANPARTY UT nF4 SLI-DR
G.SKILL 1GB (4 x 512MB) 184-Pin DDR SDRAM DDR 550 (PC 4400)
Gefore 7900GT 256MB pcie
320 Gig Seagate Sata 3gb/s HD
500 Gig WD Caviar Sata 3gb/s HD
Thanks everyone!
Wag