Project Sulaco

[tobyak]

http://i555.photobucket.com/albums/jj461/tobyak/projectsulaco.jpg

Hello All

So, im new here this will be my first of hopefully many project logs,
in the first few posts ile outline the project and whati hope to end up with

Including my inspiration, how im going to get the job done (were talking a low enough budget to make a victorian family cringe)

And hopefully gather some interest for tips, help and some much needed support

I have a background in design and a lot of plastic scratch building from an addiction to 40k in my youth. As i lack a lot of the serious tools i will be coming up with some interesting ways round common problems

By the end of this i shall be hence forth known as "Dremel Boy" or if the cutting wheel slips "The 9 finger Noob"

So watch this space for what could be either an epic tryumph or epic fail... but hell either way should be interesting

First up some of the sources or inspiration, I suspect most can have a good guess from the project name

http://i555.photobucket.com/albums/jj461/tobyak/sulaco-ir3.jpg
The good Old USS Sulaco, Marine carrier ship from Aliens

http://i555.photobucket.com/albums/jj461/tobyak/dsulaco1cm5.jpg

http://i555.photobucket.com/albums/jj461/tobyak/013-Aliens-2_L72.jpg
The Atmosphere processors may best reflect the feel, its heavy industry with big lines and chunky details

The case i am going to build on to is the NZXT Tempest EVO
http://i555.photobucket.com/albums/jj461/tobyak/top.jpg

Chunky Styling is allready a feature so it should be a superb platform to build on to

So were going with chunky industrial lines and a plated metal look to it, fan grills currently in design phase (OMG there huge) pics soon


SO why choose an NZXT Tempest evo?

Well lets look at its attributes
http://i555.photobucket.com/albums/jj461/tobyak/evospecs.jpg
For a midtower this is huge.. and that's with a capital HU!
Steel Chassis, sire its not light but it sure as hell can take punishment and support some seriously heavy gear

And of course every ones concern.... cooling... although it has none of the trappings of 20mm fans it sports plenty in the 120mm to 140mm range. for me (A die hard air cooler)
it is perfect, but also sports 5 water-cooling grommets
Did i mention the case was big???
And on a final note... the case is big lol

Side on
http://i555.photobucket.com/albums/jj461/tobyak/nzxt-tempest-evo_2.jpg
http://i555.photobucket.com/albums/jj461/tobyak/6.jpg
Large tinted window and 120m fan with filter. A slight departure from most windows as it is mounted outside the case sitting proud of the side panel, it really helps to keel the case symetrical whilst also gaining a slight amount of extra clearance for the larger aircoolers out there

Inside
http://i555.photobucket.com/albums/jj461/tobyak/nzxt-tempest-evo_4.jpg
Well we are back to "ITS HUGE" no more bleeding fingers from case edges for me, i can in stall my rig in this and use it as a spare room for guests, its clutter free and the HDD racks are tool less and can be removed completly for GFX card space or for controlers to be hidden away behind the front support


Top
http://i555.photobucket.com/albums/jj461/tobyak/IMG_4874.jpg
Recessed ports prevent them getting kicked or knocked... we all know the pain of hearing a crunch leaning over our pc and viewing the horror of a USB plus pointing 45deg out of the port, well break your ports no longer... and the area infrobt makes a handy dandy place to keep memory cards (well for me anyway)


It has great strong lines and a sharp clean shape, its huge panels leave plenty of space to mod in to/ on to/ over or through, its such a huge case with so many possabilities offered my its strong frame and sheer size that it was a huge headache picking a theme to use

I have been an NZXT fan for years, right back to the LEXA, and we are talking pre blackline edition

So without further boring you all to death (condolences to those who died of bordom reading)

Project Sulaco............

[tobyak]

To compliment my fans for this build (ENRMAX Apolish Vegas blue) I wil be making my own custom grill/intakes
http://www.digitimes.com/NewsShow/20100531PR202_files/2_r.jpg

First mock up of the front grills, all hand made form plasticard, sorry no work pics for these at this stage in the build i had not picked up a decent camera


http://i555.photobucket.com/albums/jj461/tobyak/IMG20110515_001-1-1.jpg

Ahh plasticard my new BFF

http://i555.photobucket.com/albums/jj461/tobyak/90440_Plasticard_450.jpg

All constructed in .5mm plasticard, slightly smaller then you would expect for a 120mm intake

[tobyak]

Some test fitting of some early stage additions, second of the mk1 custom intakes and some fleshing out of the panel layout


Intakes made from hand cast polyester resin in a Silicone RTV mould made form the plasticard master, all other components 3mm plasticard
http://www.fibreglassdirect.co.uk/images/10%20kg%20Low%20Cost%20Polyester%20Resin.jpg

http://i555.photobucket.com/albums/jj461/tobyak/moldes01.jpg



Finishes intake fresh out of the mould, at this stage they are very brittle, and need to cure for several days, maybe even a month to be on the safe side
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110730_001.jpg


Twin mk1 intakes and cutouts for Silverstone media panel, and blue ray drive, layed out to test fitting and space on the panel
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110515_003.jpg

And yes i know the intake flanges are not perfectly symetrical.... i have a cunning plan for that later

NOTE, allways use a canister filter mask when working with polyester resin... i did not, took 3 days before i stopped seeing double

Had some spare time today between work and fending the kids of with a dremel os have doen the prelimiary design of the side panel for Project Sulaco. Very Industrial with big intakes, think of it as a cross between an indulstrial cooling system and an escape/airlock


Prelim sketch (no laughing it was quick lol)
http://i555.photobucket.com/albums/jj461/tobyak/sketch.jpg

First stage, wire frames and checking the size works for styling
http://i555.photobucket.com/albums/jj461/tobyak/wirefront.jpg
http://i555.photobucket.com/albums/jj461/tobyak/wireoblique.jpg

Materials :


Window 7.5mm Smoked Acrylic
Frame/Bezel hand cast polyester resin
Banding 5mm alu
Panel 1.5mm alu (building on factory side panel)
Handles Billet case handles (http://www.mnpctech.com/MnpctechBillethandleGrooved.html) from MNPCtech (http://www.mnpctech.com/index.html)
Intakes Overkill Rings (http://www.mnpctech.com/120mm_Overkill_Fan_Grills.html) from MNPCtech (http://www.mnpctech.com/index.html)



Renders of the window (not true colour)

http://i555.photobucket.com/albums/jj461/tobyak/frintview.jpg
http://i555.photobucket.com/albums/jj461/tobyak/obliqueview.jpg

Still a lot more design to do before i can start some serious fabrication

Here is a few more shots of some elements that are driving the design


Sulaco inner airlock[/B]
http://i64.photobucket.com/albums/h167/deezelboy/A3/cap040.jpg

Exterior airolock of the Nostromo
http://i555.photobucket.com/albums/jj461/tobyak/lock.jpg

Why have a note on the OUTSIDE of the airlock warning against explosive bolts... if you are outside to be reading that then the bolts are the least of your worries

I am hoping to incorporate some of these details in to the finished design, perhaps not to clean and clinical as in the Sulaco's inner airlock but cretainly with the same sturdy build

Awaiting supplies for casting and some materials so on with the bezel....


First things first, test fitting
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110525_002.jpg
However soon a problem arises, IE the flanges on the surrounds are not symetrical, a minor disaster but not the end of the world. i have a cunning plan.....

First up, covering up that nasty gap between the 2 intakes with a fresh sheet of plasticard, set i place with 2 part epoxy
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110616_007.jpg

Then i needed to begin forming it to the original lines of the intakes, without some better tools then i have its time to make use of the sturdy kraft knife and some precision files, making lots and lots of incise cuts to edge my war closer to the main form, the feathering this creates also makees the final cut off much easier
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110616_006.jpg
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110616_004.jpg

3 Hours later
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110616_001.jpg
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110616_003.jpg

[tobyak]

Next up, giving it that deep set duct that i so wanted to look lik an air con or ventilation unit


For this I had to use several strips and glue then end to end to get the length strip i needed, left to dry for 48hours, a huge amount of time to dry poly ut as the glued join measured 20mm X 0.5mm it needed to be solid
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110625_002.jpg
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110616_002.jpg
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110618_002.jpg

Once the epoxy on the reverse has set i can go ahead and poly the join between the edge of the duct and the top sheet, i have allowed some extra material to remove later, I am sure all of us would rather need to remove more rather then find we had not removed enough
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110618_001.jpg
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110618_003.jpg



WOW hot day, wish i was outside but needs must, i simply haft to get these flanges fixed. The flanges on the corners were not exactly symetrical so i had the idea to raise the whole section and build a fake box on top of them to the exact shape i wanted, once drawn up and measured the gluing was easy, BUT they are only attached by there ends until i can get the side pieces put together


http://i555.photobucket.com/albums/jj461/tobyak/IMG20110625_004.jpg

Small update today... well for this morning, may be more later

[CENTER]Attached the flange sides, the beauty of this is you dont need to havean exact shape, you use the join to guide your cut
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110625_005.jpg


Finished with all flange sides added ready for first coat, as i am using plasticard for the main construction i am using a VERY thick application of satin PlastiKote clear over a matt black, not for the final finish but to provide me with a hard shell to work on top of
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110627_001.jpg[/CENTER

Whilst i wait for my joints to dry ive taken some spare time to make the replacement NZXT logo and AMD logo

[CENTER]AMD logo done, a lot less tricky then i expected
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110627_004.jpg


NZXT logo almost sorted, most of the letters turned out fine although i am on the 16th letter X
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110628_001.jpg

All letters finished with a little plinth to place on
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110628_004.jpg

DONE yay!!!!
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110628_007.jpg

And yes those letters are 13mm high

Time to start working on the mould for the window surround, i willl be using a master blank to provide the shape for the finished surround, and will be casting the mould from silicone RTV

http://i555.photobucket.com/albums/jj461/tobyak/moldes01.jpg
or a lubricated alu box (setting resin can get up to 80C and will melt plastic)

Final produce till be cast in Polyester resin

http://www.rsm-web.com/shopimages/products/normal/polyester-resin.jpg


Render of the Bezel i wil be making, caution will be the key here as the polyester resin can be brittle in the cross section i will be working in
http://i555.photobucket.com/albums/jj461/tobyak/bezel.jpg

BIG update today

With a huge influx of materials and some glorious free time ive managed to start on the blank to be made in to a mould for my resin window bezel, main blank fabrication is from 3mm plasticard, and wil be all hand cut and filed to prep for moulding, all joints will be made with polycement, it is quick cheap and effective for this material


Once marked out i can start to score the lines to create a guide path for the scalpel
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110808_004.jpg

All lines nice and deeply scored, the depth of each cut is now approx 2.5mm deep, the component can be snapped free after this point
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110808_003.jpg

And behold the first piece of the mould blank, the most critical piece as this wil govern the placement of the rest of the structure and any reinforcing needed
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110808_005.jpg

Cutting out the "rails" that i will split to make the sides and reinforcing butresses
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110808_009.jpg

First few sides and supports added, due to the pressure of 24hours immersed in a very dense liquid such as Silicone this needs to be very strong to prevent warping f the flat surfaces
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110808_011.jpg

Construction continues
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110808_013.jpg


And now finialy, my new camera, say god bye to dodgy phone camera pics

MY new Fuji all singing all dancing camera.. if this was any smarter it wold be a professor as Cambridge
http://i555.photobucket.com/albums/jj461/tobyak/IMG20110810_001.jpg


New Arrivals



Hmmm i wonder what they could be, i shall use my jedi powers to detect the cargo... I predict the one on the right are fuel rods and the one on the left is a very angry Chinhilla
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1033.jpg


Damn i was wrong....


http://i555.photobucket.com/albums/jj461/tobyak/DSCF1063.jpg

And....


http://i555.photobucket.com/albums/jj461/tobyak/DSCF1034.jpg
Yes the sweets did come with it, weird


Lets take a closer look...


Silicone RTV (Liquid silicone component)
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1035.jpg

Catalyst component
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1038.jpg

For this brand the mix is 1/10 catalyst to silicone, most have a ratio of 1/5 for the "salmon" catalysts. This is a clear catalyst mix better suited to exposure to Polyester resin

Class is shore A (20), i very resiliant silicone mix with high thermal resistance and strength, not as elastic as some classes its tearing ratio is 400% elongation



And now the cathodes....

Whats in the box


4 UV CCFLs
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1073-1.jpg

2 twin inverters
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1068.jpg

On/off rocker switches and cable bundle (ugly and will be replaced and sleeved)
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1070-1.jpg

Assorted sticky bits
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1071.jpg

UUUUU purdy (chair not included)
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1074.jpg

[tobyak]

Finishing the mould, had a good bit of time to work today so ive finished the blank and set up the mould walls to retain the Silicone RTV


My two best friends polycement and a scalpel
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1077-1.jpg

Blank finished with all the reinforcing in place, and poly is set
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1082-1.jpg

Lets break out the sander.... MORE POWER!!!!
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1085.jpg

After some brief but interesting sanding where my pet Staffordshire Bull terier tried to eat the mouse sander i finialy got the edges nice and crisp and the bottom level all ready to glue to the sheet that will form the base of my mould


Crisp, clean.... and erm.... dusty
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1088.jpg
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1091.jpg

Brushed off the dust and debris and glued the blank to the mould floor
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1094.jpg

Lots of spare plasticard cut in to strips to form the mould wall
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1097.jpg

Mould all done all ready for the RTV to go in
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1102.jpg

Time to mould



Everything you need to make the mould
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1104.jpg

Pictured above, all the things you need to finish one single part mould


Spatula
Silicone RTV
Catalyst
Blank
Mould box
Mixing vessel.... (my wife's fave cake tin)
Rice


As this is not a regular shape mould it is hard to work out the volume do you dont over or under mix a quantity of silicone


Fill your mould with rice until you have the blank covered to a depth that you feel you want for mould
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1106.jpg

Pour off the spare rice and empty the mould in to your mixing vessel, then mark the level the rice comes to as your "max fill" level
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1107.jpg


Although you may think that another approach would be to weight the rice for maximum accuracy but DONT, Silicone RTV is far more dense that rice and you will not get the same volume


Place your mixing vessel on some weighing scales and make sure you zero the reading... pour in the Silicone to the fill line.... make a note of the weight
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1110.jpg
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1109.jpg

As this is a 1-10 mix catalyst you need 1/10 (BY WEIGHT) so from the note you made on the scales work out a tenth and pour in the catalyst until you reach that weight
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1111.jpg

NOTE - The catalyst that comes with this brand of RTV is clear, i have tinted it with silicone dye for photographic use and to better illustrate a good mixture
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1112.jpg
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1113.jpg
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1114.jpg

And now we are ready to pour, do it slowly and try to avoid moving the pour stream around to much in the early stage as you will trap air bubbles
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1116.jpg
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1118.jpg

Pouring done, let it settle and check after an hour to see if the surface if free of bubbles, if it is not pop them, remember this will become the bottom of the finished mould and must be perfectly flat
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1119.jpg
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1120.jpg


Time to demould

One of the good ways to see if your silicone is ready to remove from the mould is to look at the surface it will lok tight and will have lost most of the shine it had as a liquid
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1123.jpg
Another popular but less scientific method would be "prod it a bit"

As with most materials set with a catalyst the thicker areas set first so to be 100% sure that it has set pull away one side of the mould to release the seal if its to soft push the side back and wait another 3 hours
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1124.jpg

Start taking the sides off our mold, NEVER try to take it out like a jelly mould, the suction from the material will more then likely destroy your blank and mould block before it becomes free
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1125.jpg

Starting at one edge peel the mould off the blank, this way you break the suction as you go
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1127.jpg

TADAAAAAA!!!!!!!!!!!!!!
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1128.jpg

Little bit of flashing around the mould edges, very easy to trim off
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1132.jpg

[tobyak]

All 4 parts cast, time to get the mouse sander out


Here we see the mouse sander in its natural habitat, about to pounce on this basking bezel piece
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1156.jpg

10 mins and a lot of swearing later (sanded my finger)
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1158.jpg
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1159.jpg

30mins more and even more swearing (to annoy the neighbours)
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1160.jpg
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1157.jpg

Ready to do the fine sanding ready to box up doe painting later
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1163.jpg
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1164.jpg

Its door fabrication time, that means HERE COMES THE DREMEL yay!!!!


First up, lets get this side taken apart
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1186.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1188.jpg


Tabs off, lets pop the window out
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1189.jpg


I will be using 1.5inch cutting discs from MNPCtech (http://www.mnpctech.com/DremelDisc.html)
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1194.jpg


Measuring up the new window bezel and making sure my cut lines are marked well inside the cut.... CUTTING YAY
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1192.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1196.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1197.jpg



Deburring
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1201.jpg


Well that took ages lol, but the results are exactly what i need
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1198.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1200.jpg


Next up, filling the acrylic for the window and starting the cut for the top mounting panel

Unfortunately i couldnt get any shots of cutting the acrylic out as the dust was getting in my camera, co lets ump to filing and sanding the cut edge


I will be using a rough sanding pad for this as i have a lot of material to remove
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1210.jpg


Whoops
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1211.jpg


Ahh there fixed, ther was never a huge chunk taken out of the edge... was there *swings hypnotists watch*
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1213.jpg

In the next post... i start work on the top panel

Busy week, children, fabrication, deliveries, the list goes on....

Finialy an update and i am delighted to say it is a sponsor

[CENTER]http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/nzxt1.jpg[/C

[tobyak]

SUPPLY DROP

A few weeks ago i was delighted to hear that NZXT had been kind enough to sponsor my project, for me this is fantastic, although sponsorship is a day to day affair for the more established in the modding community but for the new guy sponsorship is a big risk as they cannot be 100% sure there not being conned or that the project will not fizzle out to nothing. So once again its a HUGE thank you to NZXT



SUPPLIES
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1313.jpg

After mugging my deliveryman and fighting my way in to the packing box (cudos on the secure packing)

Lets see now we have.......

The HALE90 (850watt) (http://www.nzxt.com/new/products/power_supplies/hale90_850w)
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1314.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1315.jpg


Sentry LXE (http://www.nzxt.com/new/products/fan_control/sentry_lxe)
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1316.jpg


Blue LED lighting kits (http://www.nzxt.com/new/products/case_accessories/sleeved_led_kit_-_blue)


Unboxing the PSU, what's in the box... well ok a PSU... i ment what else
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1334.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1355.jpg
Nice to see a total lack of the typical polystyrene in favour for the non crumbely packing.
Everything in perfect condition


The PSU its self, NZXT have gone for white on the HALE90 series, with the recessed grill and 140mm fan the looks are pretty striking, and of course it IS modular
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1341.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1342.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1341.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1345.jpg


Plenty of modular cables provided, all have good quality connectors, and with the all black sheathing have a nice uniform look. and all kept safe in a little carry case
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1336.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1338.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1340.jpg


The main loom has plenty of connectors all sleeved in black braid
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1352.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1354.jpg



On to the Sentry LXE fan control

Again we have the same foam packing to keep it all safe, no part of the LXEs main unit was touching the box it was suspended in the foam for max protection, so many times have i seen components resting on cardboard after removing the cover package
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1322.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1324.jpg


Main unit is very rugged 5mm alu face plate
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1323.jpg
sadly i could not get a shot of the screen (camera flare central)


Main PCI, Connectors a plenty here with power, 5 3pin PWM fan connectors and 5 temp probe connectors
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1333.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1330.jpg


They have even included EXTRA temp probes just incase
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1326.jpg

Also included, screws for pci mount, 8 pin pci plate to control lead, pads to affix the probes and a back up battery


Last up the Blue LED strings, nice little blister pack, in the case of components like these i often see way to much in the way of packaging

http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1317.jpg


In the box we have pci plate, power lead and the string its self, the one pictured is the BLUE 100CM edition, 200CM is available
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1318.jpg


On the rear plate we have a slider for 3 brightness selections and ofcourse the On/Off switch
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1320.jpg

Once again a massive THANKYOU to NZXT for the sponsorship


http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/nzxt1.jpg

[tobyak]

BUSY BUSY BUSY, finialy has a chance to get a good run up putting the side pane together and making sure it all fits before final sending and painting

Electrical tape, the modders friend
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1434-1.jpg
This was a nightmare to get all the components in place to drill through what was technicialy a sandwich of cast polyester, steel and acrylic


More drilling.. jeez......
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1432-1.jpg

Making sure the holes line up for bolting
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1452-1.jpg
This could have been a lot easier and faster but with limited resources one hast to think out of the box


Test fitting the bezel
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1444-1.jpg
The gaps are intentional, i will be covering them with brushes alu to add a little accent


Tapping the holes for the fan/grill assembly
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1456-1.jpg


MNPCtech 120mm overkill grills, Bill Owen over at MNPCtech is making 2 140mm versions of these for me for the top
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1454-1.jpg


MORE DRILLING
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1458-1.jpg


MORE, MORE DRILLING.......
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1457-1.jpg


UUUU thats rough
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1459-1.jpg


Most of the forming done, dremel+lap sanding wheel+awesome
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1461-1.jpg


Main door fab finished, plenty of adjusting to come but thats the BIG fab done
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1463-1.jpg
The fans are perfectly central trust me..... CURSE YOU CAMERA ANGLE
NOTE the 2 triangles outside the bezel are intentional, not sure if there going to remain tiny windows or to cut them through in to blow off vents

And no way in hell am i removing the protective film untill im done

So much still to do, but its gunna be great fun

[Fuganater]

Toby! Welcome to TBCS!

[tobyak]

ahoy dude, i though i spotted you on here lol

[SXRguyinMA]

looking good so far! +sub

[msmrx57]

:stupid: And welcome to TBCS.

[tobyak]

:stupid: And welcome to TBCS.

Thankyou very much.

Lots more modding to come... ahhh photoshop i would be lost without thou

[tobyak]

Finaly got time for an update, here goes....

Time I started work modifying the NZXT Sentry LXE to modify it for the front of my case top



Cutting is going to take a while, love or hate NZXT most will say there products are sturdy and the LXE is no different, the front bezel is 5mm anodized brushed alu
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1501.jpg

let the cutting begin, for this i will be using the trusty Dremel with MNPCtech.com reinforced cutting discs (http://www.mnpctech.com/DremelDisc.html) but even with good discs this will take a while... i will spare you a million shots of cutting
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1502.jpg

2 hours.... YES 2 HOURS later......
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1506.jpg

ok now I have got the bottom off time to make it fit the shape of the case top...... time for this to go on a diet
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1505.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1509.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1546-2.jpg


ok now its the correct size
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1503.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1507.jpg


On to the next problem, this is black anodized and brushed so i have 2 problems... i need bare metal..... AND the brushing is in the wrong orientation

SANDING TIME


Flat sanding using 400grit wet and dry paper, very similar principal to lapping a CPU, but with the larger surface area this will take longer


After 30mins
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1547-2.jpg

After an hour
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1548-2.jpg

After 3 hours and 30 seconds under a mouse sander to rough the surface
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1551-2.jpg

Next up... rebrushing to match the direction of the metal i am using on the case, 800grit wet and dry until silky in apperance (you must sand only in one direction or your just sanding not brushing) after a uniform finish is attained its on to 180gritsand paper untill you end p with...

http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1554-2.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1553-2.jpg

There fixed.... coming up in next post New supply drop

[tobyak]

What's on the menu today???...... Filling... mmmmmm my favourite... *Runs ff to cry in the corner*

I hate filling but these things must me done, the first plan for the side had 2 vents on the side of the window using the old window shape as a guide, but on reflection it just looks like I missed a bit so time to bring out the filler


Spot the missing bits??http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1465.jpg

Ok here we go, first up, making plates to fill the gad befor I fill. I have cut off a lot of metal to make the window shape and i need metal of exactly the same thickness to bridge the gap in the panels.......
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/Light-Bulb.jpg

TADAAAAAAAA use offcuts for spare material
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1556.jpg

OH look a perfect fit.... LLLLIKE A GLOVAAAA!!!!
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1562.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1564.jpg


Time for the filler, i wont be giving a tutorial on this as most brands differ by huge amounts on the part to part ratios, this one is a 1-50 mix with a working time of 5mins, sandable in 20mins and complete cure in 2 hours
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1560.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1568.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1570.jpg
FYI... love the smell of the stuff...... from the yelling i am going to assume my wife does not

Worked with it a little to long but made sure i applied thick enough to get away with it....
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1561.jpg

Now on to the sanding....... there did you like that.. me too
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1572.jpg

After a full cure it is ready to prime but first.....

NURSE???????? BRING IN THE PATIENT!!!!!!!


It is time to operate on the NZXT HALE 90 PSU (http://www.nzxt.com/new/products/power_supplies/hale90_850w)

I need to get it apart to mask off for priming
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1574.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1578.jpg
A naked PSU.... shield the children's eyes

Primed. And i found out a matter of note.... spraying in a room with zero ventilation that is only 40cubic feet is not good for you......... but it sure is fun
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1580.jpg

[tobyak]

One of my fave activities today..... Chassis cutting


The NZXT Tempest Evo can accomodate a 240 this rad in the roof although you wouldnt know until you take the 140mm fans out.
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1646.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1656.jpg

So i was about to make some templates for some rad holders when as i took the 2 140mm fans out of the roof i found a set of mounting holes, now if these are for a rad im not sure but they match up to the middle set of mounting holes perfectly with 120x15mm spacing and apart from mounting i can see no reason for them to be there. The airflow is very restricted though due to the centre plate so without further ado.... LET THE CUTTING BEGIN




First up, marking out the areas to remove with extreme prejudice and a dremel....... HINT... dynamite is not accurate enough do not use.. although i doubt it would scratch this case, rugged is not the word
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1648.jpg


All marked up, now for the fun.... erm i mean "now to cut out the areas with supreme precision"
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1649.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1652.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1655.jpg


ok thats the top cut out, now for the side.. when making the side wondow i completly forgot to make sure that the fan would fit next to the drive bays..... whoops it didnt.... and so..... MORE DREMEL
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1647.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1659.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1660.jpg


By a massive stroke of luck the removed bays make a great area to install my PSU hood and new drive holders..... and now if you will excuise me i have work to do and i plan to pretend i intended to remove the bays all along......



coming up..... Cereal boxes and there many uses
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1658.jpg

[diluzio91]

where are their uses going? should be their.

[tobyak]

Fear not Guys and Gals i have not abandoned you all, i am waiting on a ton of deliveried for supplies and several sponsors including

Enermax
ASUS
SpecialTech

Lots of updates on the way as soon as i get my shipments

[tobyak]

Supply Drop

It is that time again and another supply drop has arrived, this time it is my much anticipated EK Watercooling (http://www.ekwaterblocks.com/)

So lets see what we have on the box........

Fittings, Res, CPU waterblock, MB waterblock, Pump, and Some EK UV blue coolant
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1511.jpg


First up for a closer look, the MB waterblock for the ASUS Crosshair V formula (http://www.ekwaterblocks.com/shop/blocks/motherboard-blocks/full-board-blocks/ek-fb-asus-crosshair-v-acetal.html)
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1517.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1520.jpg

The Crosshair V only has space fo a small MB waterblock but it looks great non the less
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1521.jpg
I am happy to report this comes with all the fixtures you will need and the thermal pads too


Next up... CPU waterblock (Supreme LTX AMD (http://www.ekwaterblocks.com/shop/blocks/cpu-blocks/supreme-ltx/ek-supreme-ltx-amd-acetal.html))
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1515.jpg

Ahhhh a thing of beauty, chunky and very heavy for its size, always reasuring
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1525.jpg
This also comes with all fixing you will need, and the AMD LTX blocks do not require a dedicated backplate


Next... EK multioption res 250basic
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1514.jpg

I am mystified as to why this res is called the basic, the options are just great, whilst it lacks the 2 front facing ports of the advanced model it gains a top port ideal for filling
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1528.jpg
Inclided... 2 port caps, bolts for mounting, mounts and threaded internal tube


Fixings, not a lot needs to be said here exept they are all of great quality. In a break from the norm i will be using barbs as i like the look. Same goes for the UC blue fluid, i simply cannot resist UV blue and EK has some of the best UV dye around
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1513.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1518.jpg


Last up, from EK, the pump, as i am using a cross flow rad that will be roof mounted i wont need a hugely powerful pump to move the head of fluid so i went with the nice compact DCP 2.2 (http://www.ekwaterblocks.com/shop/pumps-and-accessories/pumps/ek-dcp-2-2-12v-dc-pump.html)
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1522.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1523.jpg
Again there is plenty supplied including 3 to 4 pin converter and mounting brackets


And my radiator the Hardwarelabs GT Gen2, this is a cross flow with ports on either end rather then the traditional PC watercooling of a twin layer return flow, and perfect for my requirements, great flowrate and perfect for clearing board architecture that may get in the way of a more conventional rad
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1529.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1532.jpg

A MASSIVE THANKS TO EK FOR TAKING A CHANCE ON SPONSORING THE NEW KID ON THE BLOCK
http://h9.abload.de/img/ek-logo1-blackexn7.jpg (http://www.ekwaterblocks.com/shop/)

[Fuganater]

Gratz on the sponsorship bro!

[tobyak]

UPDATE TIME!!!!!!!


So this week its been all about the PSU cover and res holder combo
BUT.. there was a problem, when i could have ordered some nice smoked (very easy to cut and bond) Acrylic, i messed up and ordered the nightmare to cut and bond that is Perspex (plexiglass) so there was some serious outside the box thinking to get around it

First up getting all the pieces together (couldnt get pics of cutting wayyyyy to much airborne dust) )
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1721.jpg

First off i tacked all the pieces with superglue that i gelled with a little water...... it fell apart 3 times resulting in a LOT of swearing, finaly the main shell was tacked

http://i555.photobucket.com/albums/jj461/tobyak/DSCF1727.jpg
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1726.jpg

The task began of finding a way to bond the perspex in a way that could take the stresses as obviously superglue will fracture if subjected to a shock....... so..... an hour of wandering around the house searching for old stockpiles of tools and misc decorating odds and ends when an idea struck me..... why not use the car body filler that i used on the side panel...
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1728.jpg
SUCESS!!!!!!! It aint pretty but it sure is strong

http://i555.photobucket.com/albums/jj461/tobyak/DSCF1799.jpg

and the starting of the res holder an front plate
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1801.jpg
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1802.jpg
more later when the glue and filler fully cures and i can go mental with a sander


IN THE MEANTIME...... another....... SUPPLY DROP

This time Enermax (http://www.enermax.co.uk/) who have been good enough to assist me with this project with some amazing Vegas Duo (http://www.enermax.co.uk/tbvegasduo.html?PHPSESSID=1b9bab55d0eb6aaf345640d3 d0bd35e1) fans

And here they are
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1769.jpg

so whats in the box i hear you cry... well ok i dont but here it is just incase you did cry it
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1787.jpg
side by side 120mm and 140mm Vegas Duo fans, and the accessories from the the packs

Each fan comes with an attacked micro speed control and mode button
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1794.jpg
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1797.jpg
each fan also included rubber mounts and a 3pin to moles adapter

Now on to the 2 main features, the first is the brilliant click blades, a simple puch of the back of the blades and the blades unclip from the body of the fan, brilliant for cleaning and modding
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1781.jpg
at this point i need to point out that the blades are clear with a silver stripe to reflect the led arrays around the housing
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1786.jpg

and the second main feature of these amazing fans... the LED array, with the Vegas Due this is a twin array (blue red), the big brother to these the Vegas Trio have triple arrays of red, blue, green and more then 11 modes on the Duo alone
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1728.jpg

the Vegas range in action (http://www.youtube.com/watch?v=XrlKmTwkr-o)

And to finish off this supply drop the back of the box
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1792.jpg

and i simply had to add this as it just caught my eye.. there is a tab on the top to make it easier to open the fan packaging so you dont destroy the package... kinda cute
http://i555.photobucket.com/albums/jj461/tobyak/DSCF1770.jpg

A massive thanks to Enermax for the fans

http://www.enermax.de/fileadmin/enermax/css/img/bg/v2/page_header_logo.png (http://www.enermax.co.uk/)



MORE COMING SOON.......................

[TheMainMan]

Those fans look slick! Thanks for the detailed views, I thought I was seeing things until the last couple of pictures with the silver foil. Might have to pick some of these up.

Can't wait to see it all come together!

[Fuganater]

Going good Toby! I really like your PSU shroud so far!

[tobyak]

Those fans look slick! Thanks for the detailed views, I thought I was seeing things until the last couple of pictures with the silver foil. Might have to pick some of these up.

Can't wait to see it all come together!

Ive loved these fans for ages, the qualitry is bullet proof, the apollish vegas versions of these have a large control bog that you mount in the case, but these are all integrated in to the fan housing exept for the micro switch and speed dial

and heres a close up of the array for you

http://i555.photobucket.com/albums/jj461/tobyak/DSCF1782.jpg

[tobyak]

Big update in the works, another supply drop ASUS this time and more work on the PSU shroud

[Fuganater]

Looking forward to it!

[tobyak]

After 10 coats of paint and clear the side panel has finaly been MOSTLY put together, stll have the brushed accents to fit over the bevel gaps but the majority is done

Durin the undercoat and fitting of the bevel i noticed that i had forgot to redrill one of the bolt holes that go through the window, metal and resin bevel to hold it all together.... so i grabbed my trusty drill and used the origional holes as my guide


http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1803.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1804.jpg

HOWEVER, whilst drilling, the drill dropped to fast and shattered the body filler on the covered cutouts, so it was back to the filler for some quality swearing and repair work
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1805.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1806.jpg

Then it was time for more undercoating and then several layers of metalic black paint and then several layers of clear enamel, and then the headache of putting it all together
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1815.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1816.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1817.jpg

Building the side and making it work as a structure has been a long road, i dont have the tools most do for a fast job so it has been slow and steady work, there is still some finishing to do on the door but that will wait until i get the top and front bezels almost done and fitted

To finish off today's update here's some LED fan porn courtesy of Enermax Vegas Duo (http://www.enermax.co.uk/tbvegasduo.html) fans


http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1829.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1840.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1844.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1845.jpg

For all those interested, the fan grills i am using are 120mm Nautilus 'Overkill' grills (http://www.mnpctech.com/120mm_Overkill_Fan_Grills.html) made by MNPCtech.com


http://www.techreaction.net/wp-content/uploads/2011/07/logo-Enermax1.jpg (http://www.enermax.co.uk/)

http://www.mnpctech.com/CaseModStore.jpg (http://www.mnpctech.com/casemodstore.html)

[TheMainMan]

That fan/grill combo is kinda mesmerizing. Nice work on the side panel!

[tobyak]

Just before the festivities i managed to get a rare nugget of time to finish the PSU shroud

First up a monor admission...... the mk1 broke a bit.. a child of mine who shall remain nameless knocked it on the floor causing the most frantic game of jenga in the history of the universe so the repairs commenced
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1850.jpg

Once it was all reglued and reinforced it was time for some frantic filling and sanding
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1848.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1846.jpg

Once the majority of the sanding and filling was done all i needed to do before undercoating was cut a hole for
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1847.jpg

OK i will state the obvious... UNDERCOATING
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF1852.jpg

After a painfully large amount of painting and sanding and waiting for cure times i could finaly text fit it... seen here with my georgious EK multioption 250x2 res Basic (http://www.ekwaterblocks.com/shop/reservoirs-and-acc/reservoirs/ek-multioption-res-x2-250-basic.html) his res will be the corner stone of my all EK watercooling in this system
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2027.jpg
and yes i know its not lateral to the line of the case its a test fit

Next post later today the installing of my beloved water cooling

Massive thanks to EK for all there help i could not have don't this without them and there amazing products and assistance. more coming soon
http://h9.abload.de/img/ek-logo1-blackexn7.jpg (http://www.ekwaterblocks.com/shop/)

[tobyak]

As a little aside i decided to get a table saw or a bandsaw, BUT i cant afford one and my wife will kill me if i do buy one

So whats the solution..... MAKE ONE

Heres a quick guide

You will need....


Cheap workbench
Old Shelves
Spare wood (must be perfectly straight)
Wood Screws
G or speed Clamps (optional)
Cheap jigsaw


http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2054.jpg


You dont need to build big in this case the final surface area is 18inch square but use your own size it can be modified

Take your shelf or left over wood and mark out your cuts to make the working surface in my version as the shelf is 9 inches wide i need to make 2 planks 9x18
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2056.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2058.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2059.jpg

To make your joined work surface you need to use some more spare wood to make the rails on the underside, just cut your spare to match the length of the work surface and mark up a number of holes to screw the frame together
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2060.jpg

Clamp everything together tight, your final surface mush be perfectly flat
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2061.jpg

And here is how it all looks fixed together
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2063.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2062.jpg

With a set square mark up some lines so you can make sure you mount your saw perfectly in line with the sides
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2066.jpg

Drill holes for the saw blade to pass through you can have as many or as few as you want
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2066.jpg

Remove the base plate from your cheap jig saw ans drill some holes in it for your screw/bolt holes
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2068.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2070.jpg

Once you have that all put back together and have remounted your saw to its base and then to the work surface you can flip it over and mount it to your cheap work bench... this is where the split top in the bench comes in really handy to put the body of the jigsaw through, then just tighten your bench up it will grip the base of the saw and you are good to test it
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2071.jpg

i tried both free hand and with a guide i made later, i must admit free hand is a little scary you are afterall working with an upside down jigsaw but using a guide it is realy easy and the cuts are perfect. you will be able to see on the pic below which cut is free and which is with a guide
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2072.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2073.jpg


Enjoy

[Fuganater]

Epic idea!! I may have to try that.

[tobyak]

lol told ya i was going to log it

[xr4man]

that is so sweet! i need to build one.

[tobyak]

that is so sweet! i need to build one.

make sure you keep checking the screws in the jigsaw plate dont vibrate loose, im currently sorcing some flush fit bolts to bolt through the whole deck

[xr4man]

good point. the last thing you need is a wild jig saw running across the floor.

[Wordbiker]

Here's another take (http://www.instructables.com/id/Portable-tool-work-bench/step1/Jigsaw-table/) on a homemade jigsaw table.

In the past Bosch has offered a commercial jig to mount their jigsaws under a tablesaw or other. Wish I had one, it looked very slick and the tool mounted very easily.

Very much enjoying your worklog!

[tobyak]

that deserves some rep, it is very similar to the idea i hadin mind hot the end result after some modifications, the blade guide is exactly what i was looking for

[tobyak]

Supply Drop

As the project reaches its close and the next project is waiting in the wings I was delighted to hear that Bitfenix (http://www.bitfenix.com/global/en/) wanted to share some of there products with me

I am usually dubious when it comes to pre-sleeved cables you never quite know what to expect in terms of quality but i was very very pleasantly surprised

So first things first, whats in the box...


Bitfenix Alchemy Cables (http://www.bitfenix.com/global/en/products/premium-modding/alchemy-cables/)

As you can see we have a substantial drop here, including, 24pin, 3pin fan, internal IO, USB and 6pin PCIe. And an added bonus or some LED flex strips (chainable)
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2074.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2080.jpg


The 24pin connectors are very neat indeed and available in several coulurs, peronialy i like black and blue, an even sleeker look is achieved with a no heat shrink design
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2113.jpg

The same no shrink is also true of the 6pin PCIe
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2112.jpg


Some of the other cables in the range due to there design have some heat shirink but are presented very neat and precise
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2084.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2114.jpg

All pins and connectors are high qualty with well deffined pins some are plated for better contact

The sleeving realy is excelent, unfortunatly i dont have the time or resources to sleeve my HAF90 PSU but thankfully now i wont haft to, the sleeving is both dense and attractive

http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2123.jpg
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2116.jpg

Finaly we have some Bitfenix Alchemy LED Flexstrips (http://www.bitfenix.com/global/en/products/premium-modding/alchemy-led-strips)
I have seen and owned many different types of these over the years but Bitfenix have gone the extra mile and made them chain able, several connectors are included to allow you to daisy chain many strips in to one super long strip

http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2128.jpg

Each flex strip is supplied with molex connector, power lead, 1inch chain connector and a pair of micro chain connectors

http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2129.jpg

Available in a variety of colors and lengths when the description read "Super Bright" they were not kidding, 4 of these can light a large living room, and the LEDs are top notch for quality
http://i555.photobucket.com/albums/jj461/tobyak/pc%20build/DSCF2130.jpg


It is a massive thanks to Bitfenix for sharing some of there brilliant Alchemy series products with me
http://dvtests.com/wp-content/uploads/2011/04/BitFenix-logo-371x400.jpg (http://www.bitfenix.com/global/en/)