Open Air

[blueonblack]

My last project Black Oak has been put on hold for budgetary reasons. In the meantime I threw together an open-air platform much like the HPSC Top Deck Tech Station (http://www.thebestcasescenario.com/frontpage/?q=HSPC+Top+Deck+Tech+Station) out of scrap acrylic I had laying around.

The result is all right, but all right doesn't do it for me. It did, however, make me realize that with the awesome-looking hardware that's available today, there is no reason to put that motherboard and its connected pieces inside a box. Window be damned, I want it where I can see it.

The prototype I put together has the motherboard on the top level with the DVD drive mounted veritcally there as well. The PSU and hard drives are on the lower level. I made it without sides so I could see all of the hardware but I realized that the only thing down there that generates heat is the PSU, which really doesn't require massive air flow. So the new design is enclosed, with a hole in the rear panel for PSU exhaust and nothing else. It will draw air in from under the motherboard, but that's for another update.

Here's what I started with today:

Red oak scrap from Black Oak gave me the frame that will be the base:

http://www.thebestcasescenario.com/blueonblack/Project/1.JPG


After that was assembled a little time on the router table gave it a more interesting profile. I hope to continue with this square-beveled corner theme thoughout.

http://www.thebestcasescenario.com/blueonblack/Project/2.JPG


So that will be the base. More scrap pieces and the same chamfer bit gives me the corner posts:

http://www.thebestcasescenario.com/blueonblack/Project/3.JPG


These need to be sturdy, so I drilled and countersunk holes in the bottom of the base to mount them with screws:

http://www.thebestcasescenario.com/blueonblack/Project/4.JPG

http://www.thebestcasescenario.com/blueonblack/Project/5.JPG


With the posts installed:

http://www.thebestcasescenario.com/blueonblack/Project/6.JPG


The finished piece will have acrylic panels on the sides so I had to cut grooves for those:

http://www.thebestcasescenario.com/blueonblack/Project/7.JPG


And the day's work ended with the panels cut and in place:

http://www.thebestcasescenario.com/blueonblack/Project/8.JPG

http://www.thebestcasescenario.com/blueonblack/Project/9.JPG


In the end those panels will be black. I'll be painting them on the inside with Krylon Fusion, as I did with the front panel of Onyx (http://www.thebestcasescenario.com/forum/showthread.php?t=14476). The PSU lights up and I don't want anything distracting from the view of the hardware that will be mounted on the top of this case.

The size is hard to tell from the pics but it is only slightly larger in each direction than the ATX motherboard I will be using. The DVD drive and power button will be mounted in the front panel.

More to come as I am able. :D

[Aldersan]

Looks like its gunna be a pretty sweet mod!

[blueonblack]

Looks like its gunna be a pretty sweet mod!

Thanks sir. And capping it will be that very same MSI board you're running.

I hope to eventually score one of the newer Gigabyte AMD boards like this one (http://www.newegg.com/Product/Product.aspx?Item=N82E16813128514), just awesome-looking hardware, but for now my trusty MSI isn't exactly ugly.

[billygoat333]

Interesting idea!

[Fuganater]

Looks good bud!

[SXRguyinMA]

Can't wait to see how this turns out!

[xr4man]

yeah, this oughta be interesting.

[Waynio]

Subbed :) looking good blue :up: every time I see a good modder do a scraps project it really makes me want to try one. :bunny:

[blueonblack]

Thanks guys, I will try not to disappoint. :)


Next udpate will be one of the ones we all hate to do but end up doing far too often: how to fix a mistake. :facepalm:

[blueonblack]

Ok, so we all make mistakes, right? Right??

As it turns out, I'm no exception. As though I needed a reminder. For cable management reasons (among others) I'm going to have to be able to put my hand inside this box with the top in place. Obviously with the thing as it stands I can't do that since the acrylic panels slide out the top. $#&*!!

I knew that, I really did. I allowed for it in the design even, but when I was cutting away in the last session things were just going too well and I got carried away.

These two grooves should never have been cut:

http://www.thebestcasescenario.com/blueonblack/Project/9a.JPG


The plan was to make backers for the sides of this panel and hold it in place with magnets. Now I get to do that but I also have to deal with these unsightly grooves I cut. Hooray for productivity.

Since this panel will just be standing vertically with no pressure on it at all I only need very small magnets. Just the thing:

http://www.thebestcasescenario.com/blueonblack/Project/10.JPG


Now the problem is I have to get this panel to line up exactly with the grooves that I cut (that I wasn't supposed to cut). Without those I had some margin for error since a little further in or closer out wouldn't be visible. Now the edges of the panel will be lined up with the grooves and anything out of line will be visible.

I'll be using two of those tiny magnets, one glued to the inside of the panel once it's painted and one glued to a backer strip. Placement of that backer strip will determine the final placement of the acrylic. I left the panel inside the grooves and used some bigger magnets to hold the smaller ones in place where they'll be in the final assemby...

http://www.thebestcasescenario.com/blueonblack/Project/11.JPG

http://www.thebestcasescenario.com/blueonblack/Project/12.JPG


Then cut some oak strips a little shorter than the columns, pressed them against the small magnets and glued them in place...

http://www.thebestcasescenario.com/blueonblack/Project/14.JPG

http://www.thebestcasescenario.com/blueonblack/Project/15.JPG


Once the glue was dry I took the columns off and set about filling in those damned grooves. Cut two strips of scrap acrylic the same length as the columns and slightly wider than the grooves are deep, roughed them up with sandpaper so they would glue well and glued them in place:

http://www.thebestcasescenario.com/blueonblack/Project/16.JPG

http://www.thebestcasescenario.com/blueonblack/Project/17.JPG

http://www.thebestcasescenario.com/blueonblack/Project/18.JPG

http://www.thebestcasescenario.com/blueonblack/Project/19.JPG


The next step was scary because I had to get that acrylic flush with the surface of the column without damaging the backer strip that I had glued to it, but patience and a table saw got it done:

http://www.thebestcasescenario.com/blueonblack/Project/20.JPG


Fit it in place and it turned out very well!

http://www.thebestcasescenario.com/blueonblack/Project/21.JPG

So there's that mistake fixed. Whew. Too bad I screwed up the panel while I was cutting it down to its new width and had to order another piece of acrylic since that was my LAST ONE. Yes. I screwed up while repairing a screwup.

<sigh>

[blueonblack]

So the columns, the panels and the base frame are done. I needed something in the middle of the base though, and since these were scraps the frame was an arbitrary thickness, something like .584547666832243 inches I think. Roughly. Regardless, there is no sheet material known to man that thickness, whatever it is.

I had some 3/16 luan around, which would do fine once I put some support under it. New workbench tool, for those times when you need perfectly flat: 1/4" thick pane of tempered glass, complete with rounded sanded edges. I bought an old stereo cabinet (circa 1986) off of Craigslist for $5, took out this top piece and the door pane (twice that long) and threw the rest away.

http://www.thebestcasescenario.com/blueonblack/Project/23.JPG


Used the frame to mark the luan and got a press fit. Not bad on the first try.

http://www.thebestcasescenario.com/blueonblack/Project/24.JPG

http://www.thebestcasescenario.com/blueonblack/Project/25.JPG


Once it was in place I cut some more oak strips to the thickness I needed to bring the luan flush with the top edge of the base frame (or so I thought) and glued them into a rabbet I cut around the inside.

http://www.thebestcasescenario.com/blueonblack/Project/26.JPG


OOPS! Yes, again. Turns out they were a hair too thin and the luan sat 1/16 or so below the edge of the frame. Yay, fix it time again. I had a roll of self-adhesive oak veneer banding in one of my drawers from a previous project so I got to use a tool seldom used in modding:

http://www.thebestcasescenario.com/blueonblack/Project/29.JPG

http://www.thebestcasescenario.com/blueonblack/Project/27.JPG

http://www.thebestcasescenario.com/blueonblack/Project/28.JPG


I cut strips of the banding for each support I had made and glued them in place with the iron, then put the luan back. Perfect fit!

I don't have any clamps big enough for that job so I used a gravity clamp (also known as putting something heavy on it).

http://www.thebestcasescenario.com/blueonblack/Project/30.JPG


So the base is done. I also got the top done, in a more traditional method. When I made the four frame pieces I cut a groove on the inside for the luan and glued it all in place at once. Beveled the top and bottom edges plus the corners so it matched the base frame:

http://www.thebestcasescenario.com/blueonblack/Project/31.JPG

http://www.thebestcasescenario.com/blueonblack/Project/32.JPG


Top done. Almost. I'd been trying to figure out how to attach the top to the box in the most attractive way. I didn't want any fasteners breaking up the look of the wood. Magnets to the rescue again. Bigger ones.

Drilled a flat-bottom hole in each corner of the underside of the top and another in the top of each column and glued some 1/2" magnets in place. Wow, it worked better than I could have thought. I could probably toss the lid onto it from five feet away and it would end up perfectly in place. I can pick up the whole box holding just the edges of the top. :D

http://www.thebestcasescenario.com/blueonblack/Project/33.JPG

http://www.thebestcasescenario.com/blueonblack/Project/34.JPG


And here it all is together (minus the panel I'm waiting for the acrylic to fix, pay no attention to that please).

http://www.thebestcasescenario.com/blueonblack/Project/35.JPG

http://www.thebestcasescenario.com/blueonblack/Project/36.JPG


Coming together!! I have a new CPU cooler on order, my Thor's Hammer is very cool not pretty enough for this since it will be wide out in the open. Also ordered some individually-sleeved power extensions for the motherboard and VGA power (since they will also be wide out in the open) and some black 90-degree SATA cables.

Still have to cut the front panel for the DVD and the rear panel for the PSU, cut the hole in the top for air flow and power cords, mount the motherboard standoffs, sand and stain, and build the expansion card support and DVD cover.

Don't think my Tuesday deadline is gonna happen, but it's coming along.

Thanks for watching!

[Aldersan]

Lol, I know how that feels bud. Great work regardless!

[artoodeeto]

So there's that mistake fixed. Whew. Too bad I screwed up the panel while I was cutting it down to its new width and had to order another piece of acrylic since that was my LAST ONE. Yes. I screwed up while repairing a screwup.

<sigh>

I don't have enough fingers to count how many times I've done THAT. I've come to believe that the true and best way to gauge skill isn't how well you do something. It's how well you recover from your mistakes. And you, sir, recovered beautifully :up: Nice looking case so far!!

[SXRguyinMA]

it's coming along nicely!

[OvRiDe]

Looking good.. and that wasn't a mistake.. it was part of the design stage. :D

[blueonblack]

A little progress tonight. Got the breather/wiring hole cut and sanded on the top and the holes drilled for the motherboard standoffs.

http://www.thebestcasescenario.com/blueonblack/Project/37.JPG


Got the cover for the DVD drive cut, rounded and sanded.

http://www.thebestcasescenario.com/blueonblack/Project/38.JPG


And I threw together a quick and (literally) dirty hard drive rack out of scrap acrylic.

http://www.thebestcasescenario.com/blueonblack/Project/39.JPG


My cables and new CPU cooler arrived today and my acrylic is due tomorrow. Hopefully tomorrow will see me mixing stain to put a finish on the wood.

[Waynio]

Looking excellent blue. :up:

[blueonblack]

Ok, I finally finished Mass Effect 3. Immediately started ME1 again, but that's a lot less pressing and gives me some time to work on this project. :)

I got the finish put on, three coats of Golden Oak Polyshades and three coats of satin wipe-on poly. It turned out a little lighter than I wanted but the finish is perfect, has that low-gloss hand-rubbed look I was looking for. No pics because I couldn't get it to turn out with the light in my shop. Final pics shouls show it.

It took me a while to figure out how to mount the ODD, since the case is shallow enough that it woud overlap the PSU on one corner, but I got it again with scraps...

http://www.thebestcasescenario.com/blueonblack/Project/40.JPG

http://www.thebestcasescenario.com/blueonblack/Project/41.JPG

http://www.thebestcasescenario.com/blueonblack/Project/42.JPG


After getting that in place I marked and cut the front acrylic panel for the ODD tray and button and mounted the cover with magnets.

http://www.thebestcasescenario.com/blueonblack/Project/43.JPG

http://www.thebestcasescenario.com/blueonblack/Project/44.JPG

http://www.thebestcasescenario.com/blueonblack/Project/45.JPG


You can see I painted the inside of my acrylic black, as I didn't want to see the inside. It looked very nice with the smoked acrylic before, but I think it looks better black,

http://www.thebestcasescenario.com/blueonblack/Project/46.JPG


All of the acrylic is cut and painted, the drive cover is on, the finish is done, all of the parts are here. All that's left is to build the expansion card retention bracket. Another couple hours in the shop and this should be done!

[Fuganater]

Woo progress!

[blueonblack]

Finally got some time to put some more work into this. Today I got the last of the wood cut!

First off, I'm going to need a bracket of some kind to secure the expansion cards. Today's video cards are just too big to let them flop around. Besides, they look ugly that way. :)

Two more pieces of oak, corners trimmed and sanded:

http://www.thebestcasescenario.com/blueonblack/Project/47.JPG


These will be mounted to the top at the rear with screws. I drilled a pilot hole and a very neat counterbore for the screw heads, just before realizing that said counterbore serves no purpose whatsoever since the screw heads will be on the underside of the lid.

http://www.thebestcasescenario.com/blueonblack/Project/48.JPG


I'll be cutting and polishing a piece of acrylic to run across the top of these posts in the back for card mounting. To make it more versatile, I wanted to be able to remove this acrylic piece as needed without worrying about the holes in the oak getting worn out and the screws stripping them out, so I used threaded brass inserts, 6-32 machine thread:

http://www.thebestcasescenario.com/blueonblack/Project/49.JPG

http://www.thebestcasescenario.com/blueonblack/Project/50.JPG


One more piece, the button for the DVD drive, cut off the end of a 3/8" oak dowel and rounded.

http://www.thebestcasescenario.com/blueonblack/Project/51.JPG

http://www.thebestcasescenario.com/blueonblack/Project/52.JPG


Now to put a finish on these last pieces and get started on that acrylic bracket.

[Waynio]

This is turning out gorgeous mate, like the magnet fixing method too. 8):up:

[blueonblack]

This is turning out gorgeous mate, like the magnet fixing method too. 8):up:

Thanks on both counts! Magnets are awesome.

Nearing completion on this project! I had three pieces of wood to finish and them assembly. To make the finishing easier I screwed the shanks of two long machine screws into the columns...

http://www.thebestcasescenario.com/blueonblack/Project/53.JPG


And glued a piece of scrap acrylic rod to the back of the button...

http://www.thebestcasescenario.com/blueonblack/Project/54.JPG


The rod will come in handy later.

Made a poor man's drying rack out of some craft foam...

http://www.thebestcasescenario.com/blueonblack/Project/55.JPG


Took a lot longer for the finish to dry this time, must have gotten the mix wrong somehow, but the color and finish came out just fine.

I got the acrylic card securement bracket cut, painted, polished, drilled and tapped!

http://www.thebestcasescenario.com/blueonblack/Project/56.JPG


The outer two holes are just through-holes to mount to the columns, obviously, but I tapped the other seven to 6-32 machine thread.

I couldn't find any screws that I liked the look of enough to use on this high-profile portion of the case, so I decided to make my own. I had some nickel-plated 6-32 machine thread acorn nuts in a box...

http://www.thebestcasescenario.com/blueonblack/Project/57.JPG


So I took some 6-32 machine screws and cut a little bit of the shank off...

http://www.thebestcasescenario.com/blueonblack/Project/59.JPG


Screwed the shank into the nuts and presto! Shiny-head machine screws that look good against the black.

http://www.thebestcasescenario.com/blueonblack/Project/60.JPG


I used the same method to mount the bracket, screwed the shanks into the columns, set the bracket in place over them and then put the acorn nuts on...

http://www.thebestcasescenario.com/blueonblack/Project/61.JPG


One of the great things about this method (for the card mounting) is that by raising or lowering the shank in the threaded hole before putting the nut on top I can control exactly where the nut bottoms out. That lets me make every nut stop in exactly the same position in relation to the bracket. Looks a lot better in my opinion.

So on to the button mounting. Here's the hole it's going into...

http://www.thebestcasescenario.com/blueonblack/Project/63.JPG


The button goes into the hole just fine but it's too big to go in far enough to press the button to open the tray. I cut that acrylic rod down just enough to serve that purpose...

http://www.thebestcasescenario.com/blueonblack/Project/64.JPG


And put a dab of superglue on the end of it and stuck it in place. Turned out perfectly. :)

Next update will be the finished photos!!!!

(Yay, I'm actually going to finish it!)

[blueonblack]

Yep, assembly went very smoothly and I am very pleased with the end result.

My system is in its new home as I type and looking pretty damned slick there if I do say so. :D

(I'm honestly just glad I finished it!)

Pics!


http://www.thebestcasescenario.com/blueonblack/Project/65.JPG

http://www.thebestcasescenario.com/blueonblack/Project/66.JPG

http://www.thebestcasescenario.com/blueonblack/Project/67.JPG

http://www.thebestcasescenario.com/blueonblack/Project/68.JPG

http://www.thebestcasescenario.com/blueonblack/Project/69.JPG

http://www.thebestcasescenario.com/blueonblack/Project/70.JPG

http://www.thebestcasescenario.com/blueonblack/Project/71.JPG

http://www.thebestcasescenario.com/blueonblack/Project/72.JPG

[Fuganater]

Very nice!!!

[SXRguyinMA]

:stupid: super clean Shane!

[Waynio]

Very nicely done, looks awesome. 8):up: :banana:

[msmrx57]

Looks great!!! Very clean and simple. :up:

[xr4man]

oh that's just amazing looking. well done!

[billygoat333]

Very cool! great work. :banana:

[blueonblack]

Thanks very much guys!! :D

[OvRiDe]

I got to see this in person today. The pics are great but the finished product is MUCH nicer then the photo's can convey. It is just beautiful in person!

Great job Shane, and thanks for showing it to me!

[jdbnsn]

Damn I totally missed this one, that did come out beautiful! Nicely done!!