Battlefield 2 L.A.N. PC.

[danthegeek]

First off, im new to the forums so hello to everyone.

Ok, I recently stumbled upon an old army cooler that made me think doing a battlefield case would be rather cool. My only problem is I cant figure out how to implament battlefield in the case. Im going to put in military switches, convert the front and back into hinged doors and, install sheetmetal for a flat surface for the 6 inch lcd screen, control panel. The lower part of the front will be left for a fan and a hidden cdrom drive. All the hardware is pretty much figured out I just need some cool features for the theme. Bullet holes seem to be along the lines but that just isnt enough for another person to say "hey that case is a battlefield theme." There is a lid to this thing and it has al lbeen gutted. My mind just isnt as creative as i had hoped with this project and any help would be greatly appreciated.
ps- this case is ment for lan so durability is a must.

DIMENSIONS: 19 3/4in. long, 9 3/8in. wide, 13 1/8in. high

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0039b.jpg
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0037b.jpg
Dan, yes the geek.

[danthegeek]

this is how I plan on setting up the harware and the overal look of the case. I just need some advice on some ways to make this a battlefield theme. Also do you think it is a bad idea to have a cd-rom drive vertical? If so I would apreciate any suggestions about the placement.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0041.jpg
http://i101.photobucket.com/albums/m65/danthegeek/new06.png

[Nagoshi]

Wow! Pretty good work!

I really doubt a vertical drive will work well, unless it is made to be vertical, the tray need some ''holders'' for the disk to remain on it. What about placing it under the front switches and making a customized cover?

[gaz_the_chav]

Yeh the vertical drive wont work (have tried it before and dier consiquences!)

You could have it at the bottom (above the hard drive) with 2 samller fans to cool the hard drive? then on the front a little flip down bit where the tray comes out

[m4gnum]

For a military theme you can't go wrong by taking a look at http://www.creativemods.com/content/view/275/39/

[danthegeek]

Hey thanx for the reply. I didnt think putting in a vertical drive would be a good idea (thanx for reasurring me) so i am going to make a flip down panel on the very bottom of the front that hides the drive. I cant install it in under the front door because i just dont have enough room inside the case. It will hit the ram and most likely not help coolin, if you know what i mean. This is going to be an air cooled system because it will be for strictley lan use. Ill probably make the front door a little shorter sence i really dont need much room for a 6in. lcd and some switches. That will also alllw me to use a 120 mm in the front like I had hoped. Ill have to play with sketchup a little more to be sure. Oh the frame inside of the case is going to be removable, via the top, so working or upgrading this thing wont be such a pain. This frame will hopefully house a full atx motherboard and powersupply as well as the hardrives.

Thanx agin for your replies and more are welcome (hint hint)

[Clueless]

nice....wish I could tackle a project suck as this!

Edit: Meant to say "such" instead of "suck"

[Silenced_Coyote]

I'm not sure about the dimensions in your Sketch Up, but since your design has curves in the front and back, you might be able to slide the inside frame back till it hits the curve. Or maybe not all the way back so that the cables can fit. But maybe enough so that there is increased space in the front, you should be able to fit your CD drive.

[Airbozo]

I have never had an issue with my vert mounted dvd or cd roms. Most newer cd/dvd trays have the little clips in them that hold the disk in while the tray is closing. Both of the drives I have in my system were at one time verticle (whole case was rackmounted sideways), and I just checked the other systems in my house and they all have the clips.

EDIT: Now you got me curious, because while I have mounted the drives on thier side I have never tried the orientation you show in you diagram. I now have mission to try this because I have a spare cd drive to use and lots of old cd's...

[danthegeek]

I think I may do something like this. What do u think? (thanks for the front door idea). It will be placed all the way to the left to stay away from the motherboard and give room for some usb ports.


Yes that big white box on the bottom is the powersupply, I couldnt find any other place taht it will fit and still give me a rear case fan and not hit the cpu fan or be right over top of it. its okl on the bottom I guess?? Atleast it wont be the only thing you see from the top window!!

[Kaej]

That whole design looks the business! The local of the PSU shouldn't really be too much of a problem as long as you take into account 2 things. 1) The wall socket cable that plugs into the bottom of the case in your design. 2) The fans wouldnt be obstructed in the case. As long as the bottom has enough room to route a thick power cable, and enough distance from the floor to get good exhale from the PSU, then it should work fine.

Plus, repaint it like it was to begin with but minus the fact the paint was lead, that paintjob would have been sick for a military design!:D

[CanaBalistic]

Note: lead paint is only dangerous if you eat it. Small children seem to think it taste's good :)

I like your idea. I'll fallow the progress.

[MitaPi]

Yeh the vertical drive wont work (have tried it before and dier consiquences!)

You could have it at the bottom (above the hard drive) with 2 samller fans to cool the hard drive? then on the front a little flip down bit where the tray comes out

Dont use a regular drive then... use one of those drives where you feed it in. Like in a car. Problem fixed ^_^. But it looks better how it is right now if you ask me.

Very cool looking mod so far! This isnt your first time making a 3D model is it? lol

[danthegeek]

This case is my first experience with sketchup but i have used CAD a bunch of times.

I started cutting out the plates that go behind the front a rear doors. It takes forever with a dremel. I need to find a jig-saw.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0042.jpg

This is the basic idea for the back of the case. The tabs will be bent and the plate will be rivetted to the case. (helps with the militay/battlefield theme.) I figured I would start on the back to learn the best way to do the front.

SHould I use the same color for the case or go with a desert camo? Desert camo represents BF2 more then a plain olive green. What do u think? Although, the olive green that it was painted with was pretty cool. Maybe I should have left the paint on there???? It was some strong stuff, took me almost 3 quarts of paint stripper and way to many hours of work.

Im still having a mental block trying to think up some ORIGINAL ideas to pull off the Battlefield look. I figure I will throw on some rust and keep all of the dings in the case to help it along. I could use any suggestions if you have some. (normally I am not this questioning/needing ideas from others I just cant figure this one out.)

Thanks again for the replies, it makes the forums worth coming back too.

-Do you think this should go under the worklog threads? I seem to be updating my mod for then asking questions lol!

[fragged]

This case is a really really awesome idea, if i had one of those boxie thingys I'd concider making one (even though i dont like BF1942, and havnt played BF2 [yes i live under a rock on the moon])

Nice work, and awesome creativity

[Nagoshi]

This case is a really really awesome idea, if i had one of those boxie thingys I'd concider making one (even though i dont like BF1942, and havnt played BF2 [yes i live under a rock on the moon])

Nice work, and awesome creativity
LOL Ive got a Pentium3 in my house, but Ive managed to play 3 times BF2 already... outside of my house, for sure :) Two times at a LAN Party where they have their own computers (so no need for me to play only Warcraft3), and the other time at my cousin's rig.

[crazybillybob]

I've got a bit of an Idea for your DVD drive. Leave it at the bottome of the case, but move it as far forward as you can, Then Only cut out enough metal for the Drive tray. Now build a set of rails from the front of the tray to the peice you cut out. Basicly it's Stealthed just a little deeper in. You'd have to look and see how close you could get the drive to the front as you'll need the tray to stick out atleast 1/2 way so you could insert or remove disks. But if your dim's are right in Sketchup then it should let you get close enough. Let me know if you want a drawing to explain the Idea.


CrazyBillyBobb

[danthegeek]

A stealthed cd rom drive would be cool but the only proble is the area where i would have to stealth. It is quite curved and has a few other obsticles like the motherboard. I only have a 1 3/4 inch gap between the cdrom drive and the side panel. That means I have to fit the motherboard tray and the motherboard in that gap with some room to spare for the power and led connections.

Heres some pics

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0049.jpg
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0057.jpg

Do you think I have enough room for all of that?

Heres a pic of the back plate that is still onder constuction. I also have to add the back door on.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0056.jpg

[danthegeek]

Well I have decided to start up this project again sence I have som tax money:twisted: (thank you federal government.) I dont have the pics for the missing images so Ill try to post some newones asap.

Just to recap on what has been done:
-Pain..,, I mean paint removed (alot of work i might add):dead:
-The rear and front doors cut and remounted.
- ahh.. I guess thats it lol.

A|Ill add some pics later tomorrow to show where im at.

Dan The Geek

Admin: feel free to move this to works in progrees if needed.

[Crimson Sky]

:pics:

[b4i7]

use sparingly eh crimson?:p

[danthegeek]

Here are the pics Crimson. lol

These are of my design I did in sketchup almost 6 months ago. It has a removable frame from the back(almost like a removable MB tray but everything comes out except the power and accessory buttons, front fan, and DVD ROM.

Ill take some pics of the actual case later and try to post them to show my progress. Thanx for viewing

Dan The Geek

http://i101.photobucket.com/albums/m65/danthegeek/new05.png
http://i101.photobucket.com/albums/m65/danthegeek/new07.png
http://i101.photobucket.com/albums/m65/danthegeek/new06.png

[Crimson Sky]

There we go...really very cool so far.

[Zephik]

Those designs look bitchin'. I especially like the gizmo's and gadgets behind the door! That tied it all together really nice I thought.

Aren't you blocking off some of your motherboard with the PSU down there? **Nvm, your back panel through me off, but it appears that your motherboard is above your PSU. ^_^

[danthegeek]

Yeah I will be using a Micro ATX MB but expansion slot area is deigned for a full atx in my sketchup. I just got lazy and didnt feel like changing it from my old design. Thanx everyone for viewing. Ill post some real pics tommorow hopefully.

Dan The Geek

[danthegeek]

Here are the pics as promissed. I had to borrow a camera, my olo one was acting up. Oh well.

The case looks very scratched up but it is just the flash. I also want to note that the crome molding will be sanded and painted. Its not on atached well either, just a little glue, but It will get the royal treatment on the final attachment. It will also follow the edges of the case more evenly.

Thanks agiain
Dan The Geek

http://i101.photobucket.com/albums/m65/danthegeek/100_1099.jpg
http://i101.photobucket.com/albums/m65/danthegeek/100_1100.jpg
http://i101.photobucket.com/albums/m65/danthegeek/100_1108.jpg
http://i101.photobucket.com/albums/m65/danthegeek/100_1104.jpg
http://i101.photobucket.com/albums/m65/danthegeek/100_1101.jpg
http://i101.photobucket.com/albums/m65/danthegeek/100_1107.jpg
http://i101.photobucket.com/albums/m65/danthegeek/100_1098.jpg
http://i101.photobucket.com/albums/m65/danthegeek/100_1103.jpg

[Redundant]

It's wider than I thought. You did a good job on the rivets and molding. :up:
What's the vents on the back going to look like? Are you going to have two ducts, one for the PSU and one for exhaust?
One more question: how are you going to get the parts in? There's no side panel door. lol

[danthegeek]

Well I plan on using the top as an access to the parts on the inside. I hope to have the motherboard tray removable by only a couple screws but we well see:rolleyes: .

As for the rear vents for the PSU and FAN... Im not sure lol. I did plan on drilling a few holes in the rear door and the bottom and top of the door is open to allow for exhaust. Besides that Im not sure. Any suggestions would be cool.

Thanx for the comments, I love the look of the BIG rivets, almost tank like in person. The molding will be sanded and painted the color of the case. I will probably flatten it a little more so its not quite as rounded, and it will deffinetly follow the lines of the case( I like crisp edges.)

Well it looks like monday will be the day to start this agin. I hope to build most of the inner frame then.

Thanx again, Dan The Geek

Oh almost forgot, I did a little more tweaking with my sketchup and decided a full atx MB is a must. This also shows how all the doors should work when finished.

http://i101.photobucket.com/albums/m65/danthegeek/fv.png
http://i101.photobucket.com/albums/m65/danthegeek/fv2.png
http://i101.photobucket.com/albums/m65/danthegeek/fv3.png

How do I move this to works in progress?

[Bucko]

I like it! It should look good when all finished.



How do I move this to works in progress?

Send a PM to DaveW or Crimson Sky and they will do it.

[Crimson Sky]

Please fix the pics on the first page, or remove the RED X's

[Computer-Geek]

Nice work so far :up: :glasses:

[danthegeek]

Well it looks like my spring break will be of some good use this year. I have mon-fri off so I sgould be good to go with this project. sorry I havent been updating but no work has been taking place. Damn college.

[danthegeek]

Well I got a bit bored a few minutes ago and decided to see if I could make a ruff design of what I hope for in the final paint job.

This is what I came up with. Used a bit of filtering and airbrush with gimp
http://i101.photobucket.com/albums/m65/danthegeek/100_1099-1.jpg

Im not sure how i will get the effect:think: .

Well jopefully tomorrow ill stop waisting time with pictures and start on the real thing ;) . Oh well..

Any comments welcome.

Danthegeek

[PiGMaN]

I would get a toy army helmet from a toy store an bondo it into the top an make a blow hole out of it.Get some novelty dog-tags and place them some-where.

[danthegeek]

Hey that sound pretty good. I dont think I can do a blowhole though because this thing has a lid that I hope to use as storage; like the power cord, vga cable, etc. I did think about flipping the MB so its like a BTX setup. This way I could get and internal WLAN card and have the antenna stick out of the top. Oh well,, the dog tag idea ill have to use though. +rep for that.

[SgtM]

Well I got a bit bored a few minutes ago and decided to see if I could make a ruff design of what I hope for in the final paint job.

This is what I came up with. Used a bit of filtering and airbrush with gimp
http://i101.photobucket.com/albums/m65/danthegeek/100_1099-1.jpg

Im not sure how i will get the effect:think: .

Well jopefully tomorrow ill stop waisting time with pictures and start on the real thing ;) . Oh well..

Any comments welcome.

Danthegeek

I have a paint solution for that effect.

Base coat: Flat Black
Top coat: OD Green

Use the paint designed for camo applications, that will be your best match to the actual colors used by the military. After you put the green down, it's time for some wet sanding. I'd recommend something like 400 grit. It's just enough to take the green off a little, but still fine enough that by the time you see the black, you won't go all the way through it. Remember that edges will have the least amount of paint on them so, you want to go a little heavier on the black than on the green (2:1 ratio).

Or, if that's too much work, you could consider just painting the can green and then dry brushing with black.

Make sure you clear it with a flat clear coat. That will protect the paint, but it won't be glossy.

[Guardian]

Battlefield has to be THE BEST SERIES EVER!!

I honestley look forward to completion! Don't give up or else I won't stop bitchin' at you.

What I would like to see is it given a camo paintjob, but one that looks old and sturdy like its been in war. I could already imagine it. +rep

[Commando]

Here's what your looking for. The effect ya'll are talking about is called washed out.

http://www.tamiyausa.com/articles/feature.php?article-id=36

Check out the other painting articles on this website they are pretty good. These techniques are for models therefore they usually don't clear coat at the end, but I would. I think the worn look with a clear coat, although not realistic, still looks wicked cool.

These techniques are explained in depth and sound a little advanced but just use the basic guidelines for the colors and layers and you can still get a close looking effect with spray paint.

[PiGMaN]

Hey dude here is a link to a case mod you may be interestd in.
Its a military type case mod ,scroll down a bit you may find the paint work somthn youll like.http://www.themodnation-forums.com/viewtopic.php?t=62

[danthegeek]

Thanx sgtm for the idea for painting. I think Ill have to give it a try.

Guardian, Dont worry Ill eventually finish it but if you look on the first post ive been slacking off for a while.

Commando, thanx for the ideas with painting but im stuck with spray paint. I might be able to get some of those effects if im careful.

thanx again, oh and I have a little surprise for everyone.. It may have something to do with a detachable bag.

[danthegeek]

Well ive looked all over for this logo but I cant find a printable version of it anywhere (or at least close enough). Yes I have googled, any help would be great finding one. Thanx

Heres the logo im lookng for:
http://i101.photobucket.com/albums/m65/danthegeek/logo.jpg

[Bucko]

This was all I could find after a quick look:

http://img441.imageshack.us/img441/5929/usafroundeloy0.gif (http://imageshack.us)

http://img80.imageshack.us/img80/4425/150pxusafroundeluk7.gif (http://imageshack.us)

http://img405.imageshack.us/img405/7201/0365060709193458smba2.jpg (http://imageshack.us)

http://img261.imageshack.us/img261/5028/0278061101223302smeh6.jpg (http://imageshack.us)

[danthegeek]

Thanx for the help Bucko, +rep. Well not mauch to report with it being a weekend I have to work. Hopefully Monday I will get things rolling along.

Thanx again

[Omega]

Also, check the Air Force's site. They have really high-res versions of damn near every logo of theirs (including rank insignias, that thing you wanted, etc)

[danthegeek]

Small update- I decided I didnt like the way the case looked so a started almost completely over. What I didnt take off of the case is the back plate. I liked that piece so I took a bit of bondo to it to fill in the holes around the curves. Im also scratching the molding idea. I just dont think it will give it clean lines. Now I have to cut another front door for this case because the one I made before is to small. i do have a few more of these coolers to do this with.

sorry no pics, I cant find my camera but hopefully I will have them up before tomorrow night.

[danthegeek]

Well I got home from work tonight and a little package from dogtagsonline.com was sitting on the steps. I think they will be a great addition to the theme.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0063.jpg

:smoker: :smoker: :smoker:

[SgtM]

Diggin the dog tags. Really nice touch. +rep

[Commando]

Love the dog tags, awesome idea. +Rep

I hate to wear them. But they look cool as hell.

[danthegeek]

I cant take all the credit for these. It was pigman that gave me the idea and dogtagsonline.com that made them, but I except the +reps:alien: . Anyways I wanted to take some pics of the progress ive made but I have relatives staying over and they are asleep. They go home in the morning:evil: :mad: ....:D and Ill take the pics then. Sorry:alien: :alien: :alien:

[danthegeek]

I got bored and played with sketchup
http://i101.photobucket.com/albums/m65/danthegeek/23.jpg
http://i101.photobucket.com/albums/m65/danthegeek/22.jpg
http://i101.photobucket.com/albums/m65/danthegeek/24.jpg

[azminisk8r]

lol goddamn, thats your version of playing with it? thats goood:banana:

[danthegeek]

I think this mod has taken a turn. I see it no longer as a battlefield 2 mod, but rather a military theme. I just dont see it working out well as a BF2 theme unless I paint it desert camo and throw on some hidden elements from the game (tank numers, etc.) oh well.. Maybe ill stick to the plan on my future Battlefield 2142 mod (hint .hint..;) ):D

I think I can use a few ideas from this. It looks cool.. lol
IDEAS (http://www.armyrecognition.com/Amerique_du_nord/Etats_Unis/Combat_Land_Expo_2003/Land_Combat_Expo_2005/pictures/FOX_Fuchs_US_Army_ArmyRecognition_01.JPG)

[DaveW]

It does look pretty cool. :)

-Dave

[azminisk8r]

aw dude you stole my 2142 idea lol, you can make it mine wont be started til at least may, or will it???

[danthegeek]

Well I have a few more toys for this mod.

The first one is a pair of speakers that ive had for ages. They work great and they are light duty so I should have no problem running them off of a PSU. The speakers are only 2 inches in diameter and they should fit nicely in the lid of the case. After-all, what good is BF2 without some sound.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0003.jpg

The second one I made. Its a switch box that I can turn on and off 4 devices that use molex connectors. Its not done, I need to tighten the switches and line everything up but it works great

Front view
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0005.jpg
Rear view showing the connectors
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0007.jpg
A working view
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0015.jpg

[Cagedconnerman]

that's pretty cool, just looked through all the pages, and it looks really nice dan

[Canadian Eh?]

I can't wait! This looks like a great mod! How 'bout some rust paint on the switch box?

[danthegeek]

WARNING: PICS LOOK LIKE CRAP. I was in my dark basement and my camera would blow-out the image with flash and I didn't have a good spot light I could use.

I have some pics of some progress I have made. Not much but all for the better.

I scraped the molding idea because it looked like crap. Instead, The doors will be completely flush and even to the case. Im using bondo to make everything smooth and even.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0024.jpg

I also decided to use some bondo to fill in the rounded areas on the back. This was just to give me a straight line.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0021.jpg

I also made a new front panel.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0018.jpg

Everything needs to grinded a bit, sanded, and bododed to get those perfect edges:) . I will fill in the open areas around the rounded parts with bondo as well.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0016.jpg

Ill also be cutting a new door from anther cooler I have.

[SgtM]

Lookin good. + rep

[dfigravity]

Seriously...this is a freaking cool mod...can't wait to see how it turns out!

[danthegeek]

I received some fan grills from xoxide.com today. Well atleast two od the frills will be for fans:) .

These are the basic plain grills I thought would look good on the case. There are twoo of each size (120mm and 60mm)

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0028.jpg

Whats 60mm grills for, you ask? Well I needed matching grills for the speakers and they almost fit perfectly.8)

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0030.jpg
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0032.jpg

I think they will look good once painted black.

Thanks for viewing.

[danthegeek]

Almost forgot. I will also be making a power remote for this case but I am unsure of how it will be done. If you have any insight please post comments on that thread (http://www.thebestcasescenario.com/forum/showthread.php?t=7534), not in this work log.

This is the design for the remote once finished,the c4 detonator, hopefully.

http://i101.photobucket.com/albums/m65/danthegeek/Image2-1.jpg

[OvRiDe]

Check out this thread.. it may help..

http://www.thebestcasescenario.com/forum/showthread.php?p=49143#post49143

[danthegeek]

I started constructing my remote power switch that will look like the C4 detonator on Battlefiled 2.

I went to my local Home Depot and picked up this wireless and battery operated doorbell. Its made by Chime Design, model# WD-1120, and was only $10 U.S.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0043.jpg

I first ripped the entire thing apart.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0033.jpg

Secondly I wired the 5V relay I bought at radio shack to the receiver. I used solder and hot glue to insulate.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0037.jpg

I then glued the receiver into a small project box I also picked-up at Radio Shack.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0039.jpg

I wired the receiver to my pc using this diagram. No final pics because I was simply testing to make sure it works.

http://i101.photobucket.com/albums/m65/danthegeek/DIAGRAM.gif

With a new remote power switch, I have to make this project box look like the detonator from BF2.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0040.jpg

I plan on completing this box tomorrow; a little cutting and gluing should do the trick.

Comeback tomorrow to see the final results on the detonator.

Danthegeek.

[SnowFox]

Awsome mod. I love Battlefield 2. Manny pics and nice work.
+rep

[chaksq]

Sweet idea for the remote start! Just make sure no one thinks your a terrorist and calls SWAT when you go to start the thing.

[intergalacticman]

excellent!!

[danthegeek]

lol, yah I was at radio shack asking all sorts of questions and told one of the guys I was making a remote detonator. He looked at me in a funny way, so I told him it was for a battlefield 2 themed computer for remote on/off.:rolleyes:

[elbarto241]

lol, yah I was at radio shack asking all sorts of questions and told one of the guys I was making a remote detonator. He looked at me in a funny way, so I told him it was for a battlefield 2 themed computer for remote on/off.:rolleyes:

lol. FBI is probably watching this thread now :D IM INNOCENT! :rolleyes:

[danthegeek]

WARNING To 56K

Ok I started my detonator today and actually finished but, it doesn't look like the one off of BF2. Its close but definatly not the same but I still like it. The best part is it only cost me about $20 to make in total.:D

Anyways some pics.

EDIT - I took a project box and wrapped it in foam insulator for pipes to give it a rubber feel.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0044.jpg

I then started wraping the thing in some cloth I bought a wal-mart. it was cheap ($1 a yard).

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0045.jpg

I also decided to make an antenna for it using cloths hanger, a bic pen, and hot glue. No it is not functional, purely for looks.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0046.jpg
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0047.jpg
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0049-1.jpg

I then cut out the needed holes in the metal plate. One hole for the on/off, one for the led, and the other for an off switch to save the batteries:) .

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0051.jpg

I then mounted the buttons and underside for the switch.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0052.jpg

Ok, Finished. 8) I used some paint to give it a weird look but didn't work to good on the sticker. Paint seemed to dry before getting to it. Heres some final pics, but I still need to clear coat the top. I did paint over the Led because I burnt it out, ill stop at radio shack tomorrow and get another one.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0057-1.jpg
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0056-1.jpg
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0055.jpg
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0054.jpg

Thanx for lookin

Dan the Geek.

[chaksq]

Dude that detonator looks hot!

[intergalacticman]

if the FBI are watching this thread then you might want to spell raping like wrapping. lol
how did you do the paint effects on the switch?

[danthegeek]

Hmmm... I need to learn to spell.:think: :alien:

For the paint effects I Just used regular spray paint. I just found that as long as you keep the can far enough away you can get some fading but not to far or the paint will dry before hitting the surface.:rolleyes:

[OvRiDe]

Nice JOB!! I don't think the detonator could have come out better GREAT work!!

[.Maleficus.]

That really is an excellent detonator. It is very nice dude, this is coming along great.

[danthegeek]

Well, the more I looked at the detonator the less happy with it i became so I made a few modifications.

I got a new LED and a new switch.
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0066.jpg

I also made a new custom sticker with a few added features:D
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0065.jpg

and some fun pics :rolleyes:

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0067b.jpg

Dogtags
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0060.jpg

[Computer-Geek]

Nice!!!! where did u get the bullets from ? or was it photo shopped ?

[danthegeek]

The bullets are mine, just .22 caliber. I used about 150 of them in this pic:D . I bought them from an outdoor store a few months ago, but i cant remember the name of it.:think: . They were cheap so i picked up a box of 500.

[Computer-Geek]

cool ^.^

[Omega]

I like the sticker. Nothing like a little TBCS love!

[thehilitereel]

looks good bro, love the c4 trigger idea. would be cool if you could put a knife on the side with Battlefield 2 or something on the blade itself, but they probably wouldnt let you inside a lan with that thing, would they?

[danthegeek]

Probably not,... but good idea. I was going to put a knife on this but the inscribed wording sounds cool.

I plan on getting more of the case done today, I just need to get up off of my lazy but and do it :dead: .

[thehilitereel]

actually, probably sketching the total ammount of knife kills, but that goes up everyday :D

something like "256 knife kills since 2006 and counting" would be a cool idea

[Commando]

The bullets are mine, just .22 caliber. I used about 150 of them in this pic .
That would be one exciting case fire, overclocking accident.

Dude, I'm so loving this mod. Keep up the good work. +rep

[B1Gtime]

Good Work

+rep

[jdbnsn]

That detonator came out great dude! Props on the TCBS spirit also!

[danthegeek]

Thanks everyone for all the support. :D

I finished the bondo work on the front panel but my camera is charging so Ill post some pics in the morning. Ill also start on the mobo tray and supports. The fan holes in the front and back should also be a posibility soon.

Thanks again.

Danthegeek

[m33p0n3]

That detonator looks a lot better than I would've expected, great job. Whenever you finish this thing, I have to see this in person. And hey, if you need a hand/better tools I'd be glad to help out.

[Commando]

I like the sticker. Nothing like a little TBCS love!

Holy cow, I just noticed the sticker. TBCS.com. How did you do that? It's awesome. I would love to be able to figure out an easy way to paint small lettering. It's one of my goals. It's pretty hush hush in the airbrush world.

[Omega]

Thanks to your "Detonator-starter" thing, I've been inspired to make my own remote starting thing for SilverDawn. Probably won't be C4-detonater-themed, but still.


Good job. Looks pretty freakin' ace.

[danthegeek]

Commando- I just print out the sticker using inkjet "sticker paper." I did put a little extra adhesive (krazy glue) for a permanent hold.

Omega- let me know if you need any help. Its pretty easy setup (PM me if so).

Thanks again everyone.

[ChevronX]

Good luck and nice work

[danthegeek]

I didnt get anything done today but i do have some pics as promised

This is the front view of the case. I used a little bondo to make the edges nice and straight. I will also be making a new door for this asap. I hope it turns out!

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0071.jpg

I did a little modding to the to the remote AGAIN. I needed some stripes so a little masking tape and a razer blade helped me out with this. Note it is all done freehand, not bad for my first time.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0073.jpg

A night shot of the working led on the remote, Im not sure why i never posted any pics of this before.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0074.jpg

Well, that is it for now. More work on this tomorrow.

Danthegeek.

[Omega]

It just keeps getting better and better (and better).

Keep it up.

[jdbnsn]

I think that looked better without the stripes, even though thay came out nice for freehanding. Just my opinion.

[thehilitereel]

with or without, its still a cool ass addition to a bad ass mod

[danthegeek]

Thanks for the comments. :banana:

As for the switch cover, I do still have both ones so I can choose which one to keep. Im more partial to the original one myself but, the striped one matches the remote from BF2

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0076.jpg

Thanks again.

danthegeek

[jdbnsn]

How did you get that "aged" eefect on the buttons? They look fantastic, I just can't figure out how you painted them.

[NocturnaL]

Man, this is one awesome mod, I wish i woulda caught my eye on it sooner. I cant wait to see this paint job on the case, Definately +Rep worthy. Keep up the good work man

[danthegeek]

Well I did some more work on my case today. I made the motherboard tray, well actually modified an existing one. It was take out of a cheapo $10 case:D . Since the tray and rear panel were in seperate pieces I riveted them together.

In this pic you can see the two pieces together. I also painted the thing to give a nice clean finish even though it will probably never be seen.:smoker:

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0078.jpg

In this pic you can see the two pieces of angled aluminum that was attached to the back of the MB tray. This is for structural support as well were the screws will hold the tray to the case.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0079.jpg

And a quick preview of how this all fits in the case. Note that i am not dealing with much room left :rolleyes: .

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0077.jpg

I also tried to make the front door for the case but that didnt go so well. I dont have any pics of it because I got extremely frustrated with it, beat it with a hammer, and threw it in the woods.:hurt:

thanks again

-dantheggek

[Eclecticos]

I also tried to make the front door for the case but that didnt go so well. I dont have any pics of it because I got extremely frustrated with it, beat it with a hammer, and threw it in the woods.:hurt:


I know exactly how you feel. I was painting mine outside. . a wind came along and whoosh a true camo mod.. :D

[jdbnsn]

Your butt-kickin remote detonator made this weeks front page, nice work DTG!
http://www.thebestcasescenario.com

[thehilitereel]

Your butt-kickin remote detonator made this weeks front page, nice work DTG!
http://www.thebestcasescenario.com

congrats on that, you put your mind to something and anything is possible.. of course if you have the money to do the possible :devious:

[danthegeek]

Holy crap.. I made the front page.:D Go me........ ok I'm done

Well It looks like I cant give-up yet. Ill work on this thing some more tomorrow.

A thanks to everyone for the support. (tear) :)

danthegeek

[thehilitereel]

made ya a little something since I'm enjoying this case so much.

http://img20.imageshack.us/img20/6795/lanpcha0.jpg

http://img20.imageshack.us/img20/6795/lanpcha0.jpg

[danthegeek]

Wow you are ace. Thanks for the sig. Ill defenitley be using this :) .

+rep dude.

[danthegeek]

Thanks to jdbnsn I am thinking about changing the paint scheme on the case. Instead of the olive drab, he suggested a tan as seen on an Abrams with a weathered look. I think this will look great considering all of the rivets on this case. I will get a sketchup asap.

[Commando]

Man, I just saw some clips from BF2. I might just be getting that game here soon. I'm usually a BF2142 guy myself, but I'm liking what I see with BF2.


Instead of the olive drab, he suggested a tan as seen on an Abrams with a weathered look.
I wonder what a weathered Abrams looks like. I'm thinking I might have seen one of those somewhere.........

[danthegeek]

Well I cant get a worn look with sketchup so heres the color im thinkin about goin with. I know it looks a little off but trust me when I say, It will not on the real case :smoker: .

http://i101.photobucket.com/albums/m65/danthegeek/new06.jpg

More work on it tomorrow.

[derbaum]

note to self: watch the worklogs more often . definitly a kickassmod.

[danthegeek]

I have a sketchup for the top panel and lid configuration

The speakers are to the right and a storage panel for wires to the left
http://i101.photobucket.com/albums/m65/danthegeek/new06b.jpg

A closer look at the panel
http://i101.photobucket.com/albums/m65/danthegeek/new06c.jpg

And a closer look at the logo for the top. The part in white will be cut out of the top piece and frosted plexi will be added. I will use white leds to make it glow.
http://i101.photobucket.com/albums/m65/danthegeek/new06d.jpg


Thanks again

[mercerman318]

its supposed to be "due" not "do". The Design looks great though, good work

[dfigravity]

The part in white will be cut out of the top piece and frosted plexi will be added. I will use white leds to make it glow.


And the great ideas keep coming...I love this mod.

[thehilitereel]

With the C4 trigger, you added the Spec-Ops kit to the case, throw in a Medic emblem on the side somewhere?

http://www.tcnj.edu/~hofmann/Afghanistan/Vehicle.jpg

[Drum Thumper]

With the C4 trigger, you added the Spec-Ops kit to the case, throw in a Medic emblem on the side somewhere?


Sorry, had to do this:

http://i34.photobucket.com/albums/d146/drumthumper5150/catphoto.jpg

Greatest. Show. Ever.

/end hijack.

Seriously, I second the medic symbol.

[danthegeek]

Well I did a little bit of work on the case today. I did have to stop when the drill slipped and I cut my finger to the bone. But anyways some pics are what you guys want so here you go.

I mounted some 90 degree angled aluminum on the inner part of the case for some support and for the top panel to have a place to mount to.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0083.jpg

Heres an overall picture of the case so far.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0081-1.jpg

On the front panel you can see were I cracked the bondo from moving the face plate back. It wasnt straight enough and a little more bondo will have it looking pretty again.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0084.jpg

I bet you cant guess how many rivets are in this case so far. :think:


The answer is : 42 and im not done yet. :dead: . I still have to rivet the hinges, latches, MB tray, hard drive cage, DVD rom cage, etc. Uhh

Anyway, I took the idea you guys thew in into consideration. But instead of having just the one class I came up with this.

This panel will display the overall kills and deaths for all of the classes in my account. I will just have to find an LCD and someone who can program very well. If not Ill just paint the current stats when the case is almost finished.

http://i101.photobucket.com/albums/m65/danthegeek/display.jpg

[chaksq]

I did have to stop when the drill slipped and I cut my finger to the bone.

Ouch that sounds painful, are you allright?

The case is looking very good right now!

[elbarto241]

wow, sketchup models are looking LEET!
hope you didnt hurt yourself 2 badd with that drill?
how did it happen?i dont c how u can hurt yourself drilling unless your in an awkward position.....

[danthegeek]

Im ok now that I took some good pain killer. It happened when I was drilling out a rivet on a 90 degree steel bracket. I didnt have enough room for pliers so I used my hand :dead: . I didnt have my hand over the rivet, just next to it but, the drill poped through the hole because I was using to much pressure and I hit My hand at full speed. Thats an 18 volt Dewalt as fast as it will spin. So I hit my middle finger and I started oozing blood. Dumb me, I wiped it off on my pants and wrapped it in masking tape so i could keep working. After about an hour the tape was soaked a dripping and I had blood everywhere. So I got some peroxide and cleaned it out. Thats when i noticed I went to the bone, I could see my insides, and I think I cut the tendon because I cant bend it well. Oh well, just anther story. 8)

[Omega]

I want pictures of your finger.

[knightyc]

for the screen use a psone screen nice and cheap and easy to use. and for the program use samurise. It is easy to program sure someone could make you what you need ;)

[LiQuid-V2]

Yeah, pics or ban now haha

[Eclecticos]

Yeah, pics or ban now haha

Where is your pics? Fiquid. . :D

[danthegeek]

You guys are crazy. Ok if you want pics Ill warn you, Its not a grusume as before. Butterfly stitches work great for these type of things.The pics kind of blurry but, you can see where the bit went in on the right and exited on the left. The scratched part is were I yanked my finger away and ripped the skin. Trust me when I say it was oozing. Ive never bleed like that before.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0085.jpg

(I cant believe Im filling my work log with junk :neutral: .)

[thehilitereel]

I woulda cussed for a couple minutes, cleaned it up and wrapped it up with something then got back to it :D

not sure how bad this would look, but how about a little chalk board there instead of an lcd screen? or maybe a printed picture of your favorite map in the game? ...

[danthegeek]

Well Iv ordered A few parts that should be in this week.

The first parts I ordered was an on/off key to disable the remote start and the on/off switch on the case. This way I can keep tabs on everyone 8) .

http://www.allelectronics.com/images/gold/large/KSW-40.jpg

I also ordered some switches for the on/off and reset.
http://www.allelectronics.com/images/gold/large/PB-143.jpg

danthegeek.

[Indybird]

Hey where did you get that ignition? Im making a Car-themed case mod and need a car-like ignition...

-Indybird

[danthegeek]

Key Start/Arm (http://www.allelectronics.com/cgi-bin/category/700175/Key.html)

Theres the link. They have all different kinds to chose from, just scroll down and you will see them. They are cheap to, just be careful of the $7 shipping. :D

[Computer-Geek]

That key lock/switch is pretty cool i may include it in my first mod :)

[danthegeek]

Ok, I have some real updates for everyone. I got a good hour of work into this case today.

I re-cut the angled aluminum for the top plate support. The edges almost line-up but its good enoughh for government work 8) .

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0087.jpg

I also made the top plate for the case. That was probably the easiest part of all so far. My measurements were nearly dead on and I didn't screw up with the dremel once. :) I still have to trim the back plate to be flush with the top and I also have to drill the holes for the screws to secure the top.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0086.jpg
Closer Look- Front
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0088.jpg
Back
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0089.jpg
I also took a pic with the door next to the case so you can get the idea of what it will look like.
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0090.jpg

I also bought a new toy today. I got the cut-off wheels EZ-Lock kit. Let me tell you, I will never go back to the old discs. Not only does it take 2 seconds to put on a new wheel, but they last alot longer as well. Im talking 3-4 times loger.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0091.jpg

Well thanks for looking at my mod, I plan on attaching the front and raer doors tomorrow so dont stray far ;) .

-danthegeek

[B1Gtime]

Pretty Sweet, keep it up

+rep

[danthegeek]

Well I have some good news, Im done the back panel.

I cut out the holes using my dremel and then threw on some red primer and flat black.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0093.jpg

I then cut out the holes for all of the fan and Power Supply. (Tip: dont paint then drill holes, just creates more work :) ) Now I have to hit it with another cote of paint and some sandpaper.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0096.jpg

Heres a pic with the top on and I still need to drill holes and mount this.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0097.jpg

I decided to throw in some goodies so you can get the idea of how this is going together.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0104.jpg

I also put some-more bondo on the front panel, I need to hit it with some sandpaper and the dremel.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0102.jpg

I picked-up some hinges for the doors today. I think they are for gates so they should holdup well and they also seem to hollow the lines of the case.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0101.jpg

Thanks for viewing and comments welcome, good or bad :)

-danthegeek

[Eclecticos]

You did a great job cutting that out, thats one perfect circle!
I like the idea of the power supply off to the side!

I mean there always at the top and the fans usually on the top. .ya kno.

:up: :up:

[danthegeek]

Thanx, Yah the Power supply location is the only place it would fit in the case. Also sence the P.S. will have a 120mm fan on the bottom (side now), it will pull all of the hot air from the video Cards. 8)

[thehilitereel]

lookin' good

[dfigravity]

them thar is some nice clean dremel cuts. +rep...damn I love this mod!

[Ookazoo]

Cool mod man, I love BF2.

How did you do those rivets?
Also, how are you so good at sketchup?
And a follow-up, how did you make everything semi-transparent in sketchup?

I'm curious ',:|

[jdbnsn]

I think you picked a very fitting structure to mod a BF2 theme in, lovin it so far man!

[NocturnaL]

Wow that flat military green looks bad ass man, and that tan color your using is the same color im doin my case. Awesome mod, ill be keepn my eye on this until its done! so take your time ;)

[danthegeek]

Thanks for the comments everyone. I got a little bit of work done yesterday but I have to go to work soon so Ill post an update tonight or tomorrows.

Ookazoo- The rivets are just the biggest pop-rivets I could find at my local hardware store. Im not sure as the size because I have sense thrown away the packaging but When I get somemore Ill let you know. With sketchup..., well I would say Im that good but just practice with it. The hardest thing for me is the switch from AUTOCAD. Sketchup seems to be a little more deifficult at making it do what you want and to make everything semitransparent click "View", "face style", then "X-ray." under the menu bar.

Thanks again everyone.

-danthegeek

Edit-

Well I decided to throw in an update anyways :)

I worked on cutting out the design for the top plate. Behind the star and 4 rectangular holes will be frosted plexi, either red or white, but im not sure yet.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0106.jpg

I didnt finish cutting the holes because I got distracted. It turns out the star can be used as a weapon. Ninja Star TIME. (yes I did actually throw it from about 10 feet away.)

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0108.jpg

I also came up with this design for the HD cage.

http://i101.photobucket.com/albums/m65/danthegeek/hdcage.jpg

I got the aluminum bent for the supports and ley me just say, bending 1/8 inch thick aluminum is not easy task by hand. I had to do both at the same time so I would get the bends right.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0105.jpg

I still have to cut out the angled pieces for the bottom and the drill holes for the mounting screws for the HDs and the case.

thanks again.

-danthegeek

[elbarto241]

wow that top plate is going to look sweet with some plex behind it. [frosted or not]

**gets hit in the eye with ninja star** ouch!

[Ichbin]

all i can picture is the south park episode where butters gets blasted in the eye with one of those suckers.

[jakethebob]

all i can picture is the south park episode where butters gets blasted in the eye with one of those suckers.

best southpark ever

[OvRiDe]

Do I spy a 69 SS Camaro??

Great work!!

[danthegeek]

Yes you do. Ive had it 7 or 8 years now.

[thehilitereel]

I enjoy looking at your work log, you have something interesting to look at every time, good work.

[danthegeek]

Well another Update.

I finished the cut out of the top plate. The only thing is I screwed up but no worries. I think I will use thin red plexi for the stripes that go trough the center of the rectangles. It should look good, maybe enven better :rolleyes: .

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0112.jpg
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0113.jpg

I also finished the HD cage. I decided to go with 2 instead of 3 sense thats all I will need for a raid 0.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0110.jpg

And some paint.

http://i101.photobucket.com/albums/m65/danthegeek/DSCF0115.jpg

I will try to update again tomorrow but its finals week at college :dead: . Dont be suprised if I disapear for a few days.

-danthegeek

[isunktheship]

Just checked the mod for the first time, and it's looking awesome, sketching things out makes life easier!

Looking forward to more updates, you're almost done!

[danthegeek]

Well everyone, modding is on hold for a few days. I hurt my back earlier today and Im in bed now, all I did was bend down and BOOM. Shooting pains, I fell to the floor and couldnt move or breath and my father didnt know what was wrong, as I couldnt talk. I laid there, my father had to pick me up and put me on the couch. Yes I did cry, first time in a few years, but that was by far the worst pain I have every experienced in my life. Im on some godly (yes, godly, they are that good) pain killers now so I can move around.

Anyways I should get back to this in a few days

-danthegeek.

EDIT-

I almost forgot to tell everyone about my new toys. Today my dad went to a military show and picked me up a couple of ammo boxes. I dont have a pic of the big one as its not cleaned-up yet but, its about twice as tall as this one.

Thus should make for a cool HTPC.
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0128.jpg
A micro atx motherboard and power supply fit perfectly.
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0125.jpg
And a pic to show you the size. The frame behind it is a micro atx case and my everyday pc behind that is a mid-tower
http://i101.photobucket.com/albums/m65/danthegeek/DSCF0126.jpg
I shall start another worklog for this one soon. It should only tajke me a few days to complete.

-danthegeek

[isunktheship]

Ahhh sorry to hear man, I hope it all gets better and you don't have some sort of thing that would be found on the show "House".

Looking forward to your return, the project is as godly as those meds.

[jdbnsn]

This mod still moving?

[psychowit]

ya updates???

[elbarto241]

sorry to hear about the back, hope you get better soon to finish this case..... I NeEEDS mY FIX! lol :D

oh yea, what kind of engine you got in that camaro :D

[danthegeek]

ok, ok. I have no updates due to life taking over. I will hopefully start again sunday. Sorry for the delay.

[psychowit]

Nah It's cewl bro, we just love your mod and we are over eager to see it again!!!

[SgtM]

Apparrently, I have some catching up to do with this mod. Looks great though! Esp the custom made weapon. +rep

[alphastryk]

Looking great man!

I <3 ammo cans and ammo can mods (if you couldn't tell by all my work...lol)

[danthegeek]

Well I am officially starting again. My plan is to have this done by Saturday so I can go to N.J. to meet some other TBCS members.

Here is where I stand at 30% done.

http://i101.photobucket.com/albums/m65/danthegeek/Picture004.jpg
http://i101.photobucket.com/albums/m65/danthegeek/Picture005.jpg

Well I dont know if I will make it or not but I will give it a hell of a try.

I have to cut a new front door and get another lid but thankfully I have a donor for the parts.

Things Left to do:

-mount HD cage
-mount lid, front door, rear door.
-Install latches and hinges
-install speakers in the lid
-mount front switch box and key start
-finish remote start
-mount cd rom drive
-install handles
-fill holes in the sides of the body
-cut front fan hole
-Finish bondo work
-paint, paint, paint, and paint.

[danthegeek]

ITS OVER!!!!!!

It fell of the table cracked and chipped most of the bondo on the front an made a huge dent in the front plate. Im so pissed I could tear the heart out of a rhino. Oh well, life sucks.

[elbarto241]

what>!!>! NOOOOO. come on dude, you can rebuild. i had suck high hopes for this PC !

come on man it all happens to us DONT LET THIS MOD DIE!

[jdbnsn]

Noooooooooo!!!!!!!! Say it aint so! Pulease tell me you aren't scrapping this mod, first my pet tapeworm dies and now this?

[danthegeek]

OK, Ive had time to cool off and I think I can finish it if I get some more bondo tonight. GOD WHY???????
Ill try and post some pics but photobucket is being dumb right now.

[danthegeek]

Ok I have some pics

The damage!!!!
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0596-1.jpg
The paint
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0597.jpg
Top view
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0598.jpg
I still have alot of work so i dont know if I can complete it or not

-danthegeek

[Omega]

If you don't finish this, Send it to me and I will at least profusely claim that I will.

=D

[OvRiDe]

Thats not a flaw ... Thats a FEATURE! Its not damaged ... its ARTISTIC. It looks like perfectly good BATTLE DAMAGE to me. :D I have complete confidence that with your talent and creativity you will be able to either fix it back like it never happened or incorporate it in to the plan. Either way it IS a GREAT mod and and WILL be a GREAT mod when its done!

[lukeisthecoolest]

Y MUST GOOD CASES DIE SO YOUNG!

dud u gots to finish this case! it looks so good!

a little dent never stopped a tank from running! live the dream!

oh and i need some competition in the case mod conest ;) (like i don't have enough)

[Ouch!]

This mod must not die......you've spilled blood and sweat!
I love the theme and the rough military styling. I know a few ammo box mods and this one is much nicer than the run of the mill!
Please finish it!

Ouch!

[Quakken]

You can do it. You can do it. Just work through it. You can do it.

[danthegeek]

Well I wont be done in time for the NJ show but I will continue the project. Just, not today. Its 105 degrees outside my house and i thought I was going to pass out while doing bondo work on it earlier. I am going to remake the front bezel just because i want it to be as nice as it can be. Well time for a shower, Im drenched in my own sweat.

[BigJohnson]

Glad to hear this mod wont die. This mod is one of the reasons I spent so much time here. I need to see it completed. Good luck.

[lukeisthecoolest]

Well I wont be done in time for the NJ show

you should bring it anyway! i might be bringing my OPP csae without a comp inside (atleast a working one ;))

[danthegeek]

you should bring it anyway! i might be bringing my OPP csae without a comp inside (atleast a working one ;))

Its a 2 1/2 hour drive. Its a little far just to show a work in progress. When is the next show around the baltimore and philly area?

EDIT- What do you guys think about bullet holes? Should I thow a couple in or leave it the way it is. I would cover the holes in plaxi and have the red lights shine through.

Idea??
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0597b.jpg

Oh, if you have any suggestions on hole placement pm me a pic..

[danthegeek]

I bought some milliput putty from ebay to fill all of the unneeded holes in the side of the case. Hopefully it will be here soon and the temperature will cool off a bit outside so i can get rockin on this case. Im really starting to get excited :D about this again.

-danthegeek

[h3moglobe0]

danthegeek
Keep modin' !!!
This is mod I like ones. Let's Kick it !

As I see this bullet holes were shoped, right?
Not to bad. But also not to awesome.
I think that u should make ones when u finsh this. It's to ealier to get them in ur project. IMHO :P.

Keep goin' man. I like it.

EDIT

I would rather to kick it in real then goin' with bullet holes. Realy. Ram it, smash it maby.
It would look like from real first front line. Real Battlefield should bring it to U.
Thats my thoutghs :P.

[Killdrath]

I gotta say, my first thoughts were to go for real bullet holes as well. I dont know about where you are, but here they even have places where you can rent a fully auto machine gun...

[danthegeek]

I continued work today on the receiver for the remote start.

I started by taking some 3 pin connectors from old fans and wiring them to the receiver. I did this so I can easily disconnect it from the power and motherboard.

http://i101.photobucket.com/albums/m65/danthegeek/IMG_0601.jpg
I then started to sand, primer, and paint the receiver box and the front cover of the switch box.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0603.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0605.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0604.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0610.jpg
I didnt get much done today sense it was raining outside most of the day. Well, tomorrow some more interesting stuff. I start on cutting the front bezel and the front fan hole.

[lukeisthecoolest]

are u going to th NJ show at all? we need as many TBCS members as we can get!

just bring your armour case! ;)

one member down -> many more to go

[danthegeek]

Today i only had time to cut the front hole for the 120mm front fan.

I traced an outline and made my ruff cut first
http://i101.photobucket.com/albums/m65/danthegeek/Picture004-1.jpg
I then cleaned it up with the dremel, sandpaper, and the marked the spots to drill the holes for the screws.
http://i101.photobucket.com/albums/m65/danthegeek/Picture005-1.jpg
http://i101.photobucket.com/albums/m65/danthegeek/Picture006.jpg
I ended by primer and painting the edges of my cut and the front fan grill. I havent decided if I will keep it green or paint it black. The green seems to blend in and make it seem like it is built in.
http://i101.photobucket.com/albums/m65/danthegeek/Picture007.jpg


Ill post a small update later of the fan installed once it has dried. And what color should I paint the fan; black or green?

-danthegeek

[danthegeek]

Heres a few pics of the receiver box and the switch box

The switch box with its new paint.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0623.jpg
The receiver
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0630.jpg
I made a sticker and took some sand paper to it and the cover to make it look worn.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0626.jpg
-danthegeek

[p0Pe]

why not go for a 140 mm fan?, and it should be black:P... think it would look to green with a green fan as well

[danthegeek]

why not go for a 140 mm fan?, and it should be black:P... think it would look to green with a green fan as well

Well I dont have a 140 fan and I like cheap. Also, a 120 in the front and back will be plenty for this system. As for the fan color, I think black will be a good color as well. It should give it a bit more contrast and match the inside.

[danthegeek]

Well I just got back from photographing a wedding. Fun night, anyways I wont be updating until Tuesday because i will be gone. Im going to my girlfriend water front home for some fun.

Oh, anyone else have any comments on the fan color or other things on the previous page?

[AJ@PR]

This looks very nicely done.

Thanks for showing me the quick-replace Dremel discs... I didn't know those existed... but, WOW!
I. Need. Those.

I think this mod is going super great.
The BattleField theme is really coming together.
The switch panel with the lights, very nicely done.
I like the 'weathered' look you gave to the sticker.

:up: :up: Dan!
And, have fun @ your girlfriend's!!! :D

[scar~face]

Im going to my girlfriend water front home for some fun.


bown chicka wow-wow

[danthegeek]

I have some progress pics.

Not much done but at least this gives an idea of what I have been doing.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0644.jpg
I painted the top panel. The white area is actually paper but It gives you an idea of what the frosted plexi wil look like. I did a little bit of aging to the top and I will continue it on the rest of the case.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0646.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0641.jpg
The front fan finished, I just need to paint the bolts.

EDIT-I also did a quick sketch on the front bezel setup. I think I may finally be certain on the order of things.

http://i101.photobucket.com/albums/m65/danthegeek/Picture660.jpg

[Air Cooling Fan]

what type of switches are you going to use on the front panel? I've recently been experimenting with different types of toggle and push swtichs for power, reset etc. Momentary toggle switches give a great 1970s early computer look. Would also look good here.

[D1337]

Im kinda confused, you have a c4 detonator, yet after you "trigger" it, you have to bend over and put your finger in the thumb reader?

I say drop the reader and center the sticker, it makes more sense.

Other then that it looks fine.

[danthegeek]

Anyways, I now have my front bezel cut out.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0656.jpg
I then bent it at a 90 degree angle as best i could with a Rubber mallet and some angled aluminum.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0660.jpg
I laid out the front(actual size) and I will start cutting the holes and brackets for the stuff tomorrow. I have to make metal plates that everything fits into so i can remove stuff by taking out screws. Should look good.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0657.jpg
Oh, and this is what I will use to attach the cd rom to the front. I just have to cut it along the bottom tape marks and then support it with something.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0664.jpg

EDIT- On a side note, If anyone is wondering why I went with green for the color instead of beige, well it was beige. It made it look like an old office computer. So, I went with green to give it more "flare."

[jdbnsn]

If anyone is wondering why I went with green for the color instead of beige, well it was beige.

That is hilarious, I never thought of that but beize is the cardinal sin of modding, good call! 8)

[danthegeek]

what type of switches are you going to use on the front panel? I

I will be using THESE (http://www.allelectronics.com/images/gold/large/PB-143.jpg). They are big and look cool.

[danthegeek]

OK time for an UPDATE!!!

I needed something to fix the unneeded holes in the side of the case. So, I went to Autozone and bought some "Quick Steel." So I used this and it worked great. Its so strong, I dont have to worry about the holes anymore. If I need to drill a smaller hole in the same spot I can.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0683.jpg
Right Side holes fixed and primed.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0675.jpg
Left Side holes fixed and primed.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0673.jpg
For the front I used the "Quick steel" again to attach the front panel and primed. Trust me, it isnt coming off. I tested it with other scrap pieces and a hammer. I destroyed the steel before it even started to crack. I just need to fill in the gaps a bit and sand the primer smooth.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0674.jpg
While the primer was drying, I cut the bracket for the CD-ROM drive. Easy enough
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0677.jpg
I went ahead and marked to screw holes for the top cover.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0679.jpg
The I used a small drill bit (forget the size) and made a hole for the sheet metal screws.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0678.jpg
The finished product. If you notice the top left screw has a brocken head. Nothing some vice-grips cant fix.:) .
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0680.jpg
Once the primer was dry I sanded the entire case and primed it. A little smoother and I will need this when I paint it and blacken in some areas like I did for the top cover.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0681.jpg
Once that was dry I took some black paint and painted the underside of top cover and the case. Ill let them dry over night and start work again tomorrow.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0682.jpg

Thanx for viewing.

-danthegeek

[BigJohnson]

Looking incredible man. Can't wait to see the front panel finished. That's when I'll lose it. Just awesome.
+Rep

[p0Pe]

so nice, but wouldnt it fit better with some... more military liking switches or are you gonna paint them?

[Omega]

I really need to find a nice, big ammo can now =p

seriously

[p0Pe]

I really need to find a nice, big ammo can now =p

seriously

+rep if you build a pc into one of these things:D
http://www.bf-games.net/images/bf2/waffen/kord.jp

sry for off topic, but could be a great mod right:p

[Omega]

yeah, no =p

I doubt you could fit anything larger than a mobile-itx in there anyways (and it would have to be in the hopper)

not to mention the last thing I need is cops to come into my house and see that I have (what appears to be) a support weapon...

[Killdrath]

Omega, I can get ammo cases here in Vegas... Got friends on base. Got a particular size yer looking for? I have one right now that is roughly standard case size. I forget what ammo it carried originally, as I sprayed it black a long time ago. Can probably get a couple more of those fairly easily (I think it was 20mil ammo)

[danthegeek]

+rep if you build a pc into one of these things:D

sry for off topic, but could be a great mod right:p

Well, omegas right. Its to small and to big at the same time.

Ill try to update tomorrow, nothing got done today since me and my girlfriend where out all day.

-danthegeek

[danthegeek]

OH I finished the back door.

I started by evening up the door to the case as much as possible. Its close enough. I also had to cut off two rivet heads on the left side of the case so i could attach the hinges.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0702.jpg
After they were cut, I taped everything up to mark the holes and then drilled.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0704.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0705.jpg
Before I attached the door, I wanted to cut a small hole in the bottom for air ventilation. So, I marked it off and then cut it with the handy dremel. I intend to put some mesh in the hole as well.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0706.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0707.jpg
After that, I attached the door with the hinges.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0711.jpg
I then marked the holes for the latches and attached them as well.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0713.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0715.jpg
I then sanded and threw on some primer to protect the metal.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0716.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0720.jpg
I hope to start the front tomorrow but that will be a challenge. I have to cut a piece out of another case to create a door for this one. O just hope I dont screw-up the measurements.;)

Thanx for looking,
-danthegeek


On a side note:

I think it looks much better then it did before the overhaul.

Before
http://i101.photobucket.com/albums/m65/danthegeek/100_1100.jpg
After
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0722.jpg

[BigJohnson]

I don't know man. I think it looks awesome after the renovation. I cant wait to see this one finished. Then I can start my ammo can mod after this. This mod is an inspiration. Good luck with the rest. I'll be watching.

[danthegeek]

Thats what I meant, It looks SO much better now. 8)

EDIT- AND thank you for your complements, I was in a hurry earlier and had to respond quickly.

[scar~face]

i think when you search "awesome" on wikipedia, this mod should show up

[danthegeek]

i think when you search "awesome" on wikipedia, this mod should show up

Thank You. I just like to have fun and take my time. This is my therapy, much better then sitting down on a couch and having someone make you talk to a doll for an hour.

[Omega]

This is my therapy, much better then sitting down on a couch and having someone make you talk to a doll for an hour.

This is so true, it's going in to my sig.

[h3moglobe0]

I know one thing

Show to us your big black eyes and grey skin, now!
Why there is no pics off you? Cuz you aint' human!

This is creaziest shi+ ever. Ehhh.


This is my therapy, much better then sitting down on a couch and having someone make you talk to a doll for an hour.


Plz don't seat on couch then! Ever! Just modd. Anything you want and post it.
It's a real pleasure to look at this work.

I wonder, why am I so Lazy ?? fsck! :D

[danthegeek]

I know one thing

Show to us your big black eyes and grey skin, now!
Why there is no pics off you? Cuz you aint' human!

This is creaziest shi+ ever. Ehhh.


Plz don't seat on couch then! Ever! Just modd. Anything you want and post it.
It's a real pleasure to look at this work.

I wonder, why am I so Lazy ?? fsck! :D

HAHA. Ill have my girlfriend take a pic of me tomorrow. Actually, I dont have a pic of me.

Anyways, thank you for your complements


Ok, a small update for everyone.

I got the front door cut out and mounted, I didnt take any pic of the process because it was just like the rear door just much more complicated. Trying to take a piece of metal out of another case and make it match this was quite a task. I took about 7 hours total until i was happy with it enough to mount it. I also had to fill in a bunch of holes because it was severly corroded.

PICS

front with handle
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0738640x480.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0739640x480.jpg
hinges
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0736640x480.jpg
latch
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0737640x480.jpg
In case you were wondering how strong this is, I picked it up by the front door. Its solid as a rock and didnt flex a bit. I think it could be fully loaded and still have the handles be functional.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0740640x480.jpg

Thanx for viewing

-danthegeek

[scar~face]

if this mod gets any better, i might just cry

[danthegeek]

Oh, I forgot

I took a pic of the plexi after I frosted it. I took my desk lap and used it as the light.

http://i101.photobucket.com/albums/m65/danthegeek/IMG_0741.jpg

Thanks again for the complements.

-danthegeek

EDIT- Got some more pics

no light on the plexi
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0751640x480.jpg
The lid (not attached or sanded and prepped). I put the can next to it so you get an idea of the size of the case
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0744640x480.jpg
This is my plan for the bottom of the lid. I will mount the speakers in the front and have a storage area for wires and crap. Maybe even a knife ;)
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0749640x480.jpg

[scar~face]

ya know what else would look sweet up there? some gauges, like temp, cpu usage or HDD RPMs.

the frosted plexi look really good, what colour lights are you planning to have inside?

[Blackout]

im not usually a fan of modes like this but im really getting into this one the workmanship is top notch, its really starting to shape up nice

+rep

[danthegeek]

ya know what else would look sweet up there? some gauges, like temp, cpu usage or HDD RPMs.

the frosted plexi look really good, what colour lights are you planning to have inside?

Ill have to see what I can do for some gauges, that may come later due to tight funds on my end. As for the plexi, I plan on having white lights make it glow and red lights on the inside of the case to shine out the front. of course, they will be on switches so I can turn them off.


im not usually a fan of modes like this but im really getting into this one the workmanship is top notch, its really starting to shape up nice

+rep

Thank you, I appreciate your interest and support.

-danthegeek

[Killdrath]

OMG minty, your new sig line had me almost snorting my pepsi out my nose!

[danthegeek]

I have cut out the piece to insert into the lid but I have yet to cut out the storage and speaker holes. I have the lid outside covered in paint striper and the mosquitos are to bad to work any further. Ill post some pics tomorrow morning or sunday. I am a bit busy tomorrow evening.

-danthegeek

OK, this is for the slect few that believe I am some type of dark elf.
http://i101.photobucket.com/albums/m65/danthegeek/mypicture.jpg

See, I told you I was human. Although my girlfriends picture taking skills could use some improvement. Blasted me with the flash.

[Ouch!]

Gotta love this mod!

It's right up my street!

I hope the new Interocitor is half as good.

Ouch!

[jdbnsn]

OK, this is for the slect few that believe I am some type of dark elf.
http://i101.photobucket.com/albums/m65/danthegeek/mypicture.jpg

See, I told you I was human. Although my girlfriends picture taking skills could use some improvement. Blasted me with the flash.

Nice try Dan, but your girlfriend told me that you photochopped that pic. Thankfully she was kind enough to send me the original...

http://www.thebestcasescenario.com/jdbnsn/misc/elf.jpg

[danthegeek]

Nice try Dan, but your girlfriend told me that you photochopped that pic. Thankfully she was kind enough to send me the original...


HAHAHAHAHAHAHA :eek: You figured it out.

Thanks, you just made my day.

[danthegeek]

Now that the site is back up, time for an update.

I cut out the piece for the underside of the lid. It tuned out good enough, it even snaps right in.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0786.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0787.jpg
Then I made the bracket for the speakers but, I decided not to go with a storage bay yet. I really like the idea of the gauges and I dont want to mod myself into a corner.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0788.jpg
Then the camera died so there are no pics of me attaching the metal plate, hinges, cutting, blah blah. I just couldnt wait for the camera to charge

This is where I stand so far, everything primed and some areas painted black (inside of doors, inside case, etc.)
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0793.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0792.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0791.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0790.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0789.jpg
I also need a way to latch the lid but i dont want to go with the same latches as the doors. And I dont want them to look out of place either. Hummm, I may not go with latches sense gravity holds it down and the hinges are pretty stiff.

I will finish the front panel tomorrow and start painting. I hope to be done by the weekend so dont stray to far.

thanks again

-danthegeek

[h3moglobe0]

Gotta love this mod!

It's right up my street!

I hope the new Interocitor is half as good.

Ouch!

Differences are plain to see. Danthegeek is buildin' up all, u r doin' a stealth mod. Both are awesome, super sweet and keowel:P.

One thing. I didn't say that u, danthegeek, are a darkelf. I meant UFO/alien, rather, but... I if u want:P. Too many RPG's dude.

This pic was realy shoped(first one posted by danthe, I mean).:D:D LOL.

My propose is to make a collectors edtion too. Wallpapers I mean- it would be great have this one on your desktop.

PS. Dude. Ur lookin' like my old classmate. It's gettin' weird every day.

[danthegeek]

Another update

I started work on the front bezel today

I got the cd rom drive opening cut out and the supports mounted
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0796.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0797.jpg
I also taped of and cut out the hole for the switch box
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0798.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0799.jpg
Then I decided to mount the MB tray into the case. I used some small rivets and some paint to finish it off
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0812.jpg

I painted the underside of the frosted plexi white. I dont want the red lights turning it pink and this was the best way I found.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0800.jpg
Tomorrow I will cut out this piece and cut a hole in the front for the switches. This goes to the right of the switch box as shown in the previous design.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0816.jpg
Another update tomorrow so dont go far.

Thanx
-danthegeek

[NamesAreUseless]

Hmmm....It needs rust....

[danthegeek]

I may go with some rust once I get and air brush.

Small update.

I cut out the panel for the power/reset switches and such. I used the switch box panel as a template so they match (the one I cut out is the smaller one).
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0817.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0818.jpg
I then cut out the holes for the buttons and leds
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0819.jpg
Then some paint on them both. I also cut out a panel for the usb that will be on the side of the case.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0825.jpg
Ill start final details tomorrow and then some paint.

thanx for lookin

-danthegeek

[alphastryk]

looking great man!

[danthegeek]

What tool are you using to make your cuts?

I use a dremel for anything small and a jig saw for the bigger stuff such as the front bezel and cover for the lid. I want to straiten up my cuts in the front but I was out of discs until 10mins ago. Ill finish the straining and tomorrow. Today was a to busy a day.

Thanks for the compliments.

-danthegeek

[danthegeek]

I got a little bit more work done today on the pc.

I started by making a support for the lid so it wont snap the other doors of when you open it. It was putting a lot of pressure on the doors so I got some small cable and put some ends on it.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0827.jpg
Then I mounted it to the lid and back panel using some rivets. It may not look great but this was the best and simplest way I could find to do this. Remember, it has to function too.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0828.jpg
Then I mounted the rear hinge.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0831.jpg
I also mounted the hard drive cage using some drill screws. Its easy to detach it as long as you have the front overhanging a table or something.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0830.jpg
The bottom shot
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0829.jpg
Some black paint. I know you may think theres a lot of overspray but I will mask off the areas I want to stay black and the green will cover up the rest.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0835.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0833.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0836.jpg
Tomorrow some more paint and some finishing touches. I should have it finished in a day or two, as long as I am happy with the paint. The real time killer is waiting 4 hours for paint to dry before i can touch it.

OH, some hardware.

Old AMD 3700 (free from my shelf) and motherboard. Also a new sata DVD writer from newegg ($30) and a free 160 gig seagate HD. Tomorrow the 8600gt, 1 gig ram, and 400 watt Ps whould be here from newegg.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0841.jpg
Thanks everyone for looking.

-danthegeek

[The boy 4rm oz]

This is some seriously good work, great job.

[b4i7]

glad this case is still goin...i like it a lot

[danthegeek]

Ok ANOTHER UPDATE.

something you may be interested in, paint. Yes that was my goal for today and I accomplished it, but dont let me get ahead of myself

I started by taping off the areas I wanted to stay black and threw on some primer after sanding.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0845.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0846.jpg
Then I put on 5 layers of green so I would get a good even coat.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0848.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0847.jpg
Well that doesent look right, too new. SO I threw on some black for the darkening and aging effect.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0849.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0853.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0854.jpg
Then once the paint wasnt to tacky, I took off the paper and tape.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0855.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0856.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0857.jpg
I think the black handles and black front work well with the color.

Anyways, i will let this dry a few more hours and then start assembly if I can. I dont want to mess-up the paint with finger prints and huge scratches. I dont plan on sanding any of it down to make it look more worn because I want to protect the metal.

[AMD_TaT3rs]

this looks awesome. i cant wait to see it finished. its going to look amazing. keep up the good work.

[calumc]

I just realised something: I LOVE THIS CASE!!! +rep 4 u!

[danthegeek]

More pics in better lighting. I also finished the front bezel. I dont know if I will paint the screws or not. The crome look gives it some contrast.

http://i101.photobucket.com/albums/m65/danthegeek/IMG_0863.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0860.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0865.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0864.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0859.jpg

thanks for looking

-danthegeek

[Xpirate]

I have followed this work log from the beginning. You did truly excellent work.

[Omega]

That's freaking awesome.

We want more pics.

And by we, i mean me and my buddy whose reading my laptop right now.

[Ap1thy]

now this is one sweet project, building a case from scratch is one thing, but modifying one to this level is a whole other. SWEET!

[The boy 4rm oz]

Great job on the painting, looks really good.

[danthegeek]

We want more pics.


Ok, more pics.

I made some stickers for the front and also took some sandpaper to the front to give it a used look. Also some lights :D. Im still waiting on my red cold cathodes.

http://i101.photobucket.com/albums/m65/danthegeek/IMG_0868-1.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0875.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0876.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0883.jpg

Sticker Says
WARNING
-Welcome to the Battlefield 2 L.A.N. PC Command
Unit

-When Using this device use extreme caution not
to exceed thrill levels your body can endure.

Thanks for all the comments, but Im not dont yet. I still need to wire and mount the speakers, make a sticker for under the lid, get my lights, finish painting grills and bolts on the front, install the Motherboard (I dont have any stand offs for the tray) and the rest of the hardware.

-danthegeek

[The boy 4rm oz]

That looks great, you have really outdone yourself. An excellent job. +rep

[Ouch!]

Looking excellent!

If you turn up to a LAN party with that: they'll all **** themselves!

[The boy 4rm oz]

Haha yeah I bet they would, you would win best dressed for sure.

[BigJohnson]

Just awesome man. This thing has only gotten better since I've started watching. Everything a good idea. I cant wait to see it finished.

[elbarto241]

simply one of the best BF2 mods out there. +rep for sticking with it through thick and thin :D

[danthegeek]

Thank you all for your comments and compliments. I would have never gotten this far without the support from all of you.

Now, this is the part of the worklog when I start lecturing all of.

j/k , but seriously, I can never say enough to always plan every aspect of a mod. That is what makes or brakes a build.

I show you why. I knew that everything was going to fit tightly into the case and I am extremely glad I measured twice.:D

While installing the video card I knew it was going to be close to the power supply, but not this close. The video card has 1 mm. between it and the power supply. Yes 1mm, maybe less. lol but it is not touching it. Heat will not be an issue though because the power supply has a 120mm fan pulling air past the card.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0889.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0888.jpg
Also the memory has about 4mm between it and the DVD-rom. You can also see the 24pin connector was a close call as well because of the dvd-rom cage.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0890.jpg
Atleast it all fits. Now I have to see if I can get the usb working. for some reason it will not install anything properly or recognize it and I dont know if it the motherboard or windows. I may do another clean install and see what I come up with. Any ideas?

Thanks again
-dan

[danthegeek]

Well I have the hardware and software part of this mod done. The only thing left is a lot of wire management. I still have to take everything out of the case again so I can run my speaker wire neatly (dont want bits of metal in the new goods). All I need to do to finish the case is get the red and white lights and I will be done.

Question, I cant figure out how to get the usb working. Ive tried reinstalling windows, bios update, new drivers, and I still get "unrecognized device" on everything I try (mouse, keyboard, camera, flash drive, etc.). My ethernet slows down after a few minutes as well. I guess I will gave to get a usb pci card and try it out or get another MB.

Besides that, it runs games great (oblivion @ 1400 * 900 Med all day long with no lag).

[The boy 4rm oz]

I wanted to get an XFX 8800GTX but they were hard to find, The 8600GTS is a great card, personally I would have spent the extra and got the GTS but it will chew through BF2 all the same.

[.Maleficus.]

I wanted to get an XFX 8800GTX but they were hard to find, The 8600GTS is a great card, personally I would have spent the extra and got the GTS but it will chew through BF2 all the same.
Yeah, but does the GTS have the mandatory-for-a-BF2-mod dog tags on the heatsink :p? It's the little things like that that really pull a mod together.

Anyways man, I can't wait to see this done. This is looking soo good. It's making me want to build a LAN machine myself.

[The boy 4rm oz]

I don't know about the dog tags, i generally go for power. I think the whole XFX8600*** series sports them.

[danthegeek]

Sorry I haven't been posting but I've got pretty sick over last few days. I may get some work done tomorrow if I feel a bit better.

-danthegeek

[danthegeek]

Ok, I got bored and decided to make a small slide show of the mod so far. I like it but it is only a minute long and I plan on doing a hole slide show with progress and finished video. This is kind of like a teaser.

enjoy.

EDIT- I changed it a bit


ue0WApg390o

[D1337]

does the key do anything or is it purely appearance?
also what does the text say on those bricks o.o

[danthegeek]

does the key do anything or is it purely appearance?
also what does the text say on those bricks o.o

The key arms the power switch so you can turn the system on. What do you mean by "bricks." Do you mean the label, if so then:


WARNING
-Welcome to the Battlefield 2 L.A.N. PC Command
Unit

-When Using this device use extreme caution not
to exceed thrill levels your body can endure.


Ok, I got a bit of work done.

I finished wiring the speakers and they work great. I ran the wire to the back and into the lid from the bottom so they are hidden when you shut it. They are nice and loud to. I will try to get a video of it once I remake that bracket that holds the speakers.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0896.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0897.jpg
I also put in a speaker input in an expansion slot so you can plug in you ipod, cd player, pc, whatever into the speakers.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0898.jpg
I added the mesh to the rear panel. I dont see how it will do any good sense the door has to be open to run the pc. I may make a small opening for the wires later.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0901.jpg
I made a template and added a U.S. emblem in the rear door. I added a little over-spray to make it look more realistic.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0899.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0900.jpg
I was wondering what your opinions on adding some handles onto the front was? I like the looks of them and that is all they would be there for. Do you think Im trying to add to much? Anyways, Id love to get some opinions to help my decision sense I cant decide.
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0907.jpg
http://i101.photobucket.com/albums/m65/danthegeek/IMG_0909.jpg
Thanks for looking

-danthegeek

[The boy 4rm oz]

I think the handles would fit perfectly, it gives it the whole getting lugged around and bashed feel. Suites perfectly.