Battlefield 2 L.A.N. PC.

This is the worklog for the "Battlefield 2 L.A.N. PC."

Finished Product

Please take a look at the process and time needed to finish this project

First off, im new to the forums so hello to everyone.

Ok, I recently stumbled upon an old army cooler that made me think doing a battlefield case would be rather cool. My only problem is I cant figure out how to implament battlefield in the case. Im going to put in military switches, convert the front and back into hinged doors and, install sheetmetal for a flat surface for the 6 inch lcd screen, control panel. The lower part of the front will be left for a fan and a hidden cdrom drive. All the hardware is pretty much figured out I just need some cool features for the theme. Bullet holes seem to be along the lines but that just isnt enough for another person to say "hey that case is a battlefield theme." There is a lid to this thing and it has al lbeen gutted. My mind just isnt as creative as i had hoped with this project and any help would be greatly appreciated.
ps- this case is ment for lan so durability is a must.

DIMENSIONS: 19 3/4in. long, 9 3/8in. wide, 13 1/8in. high

Dan, yes the geek.

this is how I plan on setting up the harware and the overal look of the case. I just need some advice on some ways to make this a battlefield theme. Also do you think it is a bad idea to have a cd-rom drive vertical? If so I would apreciate any suggestions about the placement.

Hey thanx for the reply. I didnt think putting in a vertical drive would be a good idea (thanx for reasurring me) so i am going to make a flip down panel on the very bottom of the front that hides the drive. I cant install it in under the front door because i just dont have enough room inside the case. It will hit the ram and most likely not help coolin, if you know what i mean. This is going to be an air cooled system because it will be for strictley lan use. Ill probably make the front door a little shorter sence i really dont need much room for a 6in. lcd and some switches. That will also alllw me to use a 120 mm in the front like I had hoped. Ill have to play with sketchup a little more to be sure. Oh the frame inside of the case is going to be removable, via the top, so working or upgrading this thing wont be such a pain. This frame will hopefully house a full atx motherboard and powersupply as well as the hardrives.

Thanx agin for your replies and more are welcome (hint hint)

I think I may do something like this. What do u think? (thanks for the front door idea). It will be placed all the way to the left to stay away from the motherboard and give room for some usb ports.


Yes that big white box on the bottom is the powersupply, I couldnt find any other place taht it will fit and still give me a rear case fan and not hit the cpu fan or be right over top of it. its okl on the bottom I guess?? Atleast it wont be the only thing you see from the top window!!

This case is my first experience with sketchup but i have used CAD a bunch of times.

I started cutting out the plates that go behind the front a rear doors. It takes forever with a dremel. I need to find a jig-saw.

This is the basic idea for the back of the case. The tabs will be bent and the plate will be rivetted to the case. (helps with the militay/battlefield theme.) I figured I would start on the back to learn the best way to do the front.

SHould I use the same color for the case or go with a desert camo? Desert camo represents BF2 more then a plain olive green. What do u think? Although, the olive green that it was painted with was pretty cool. Maybe I should have left the paint on there???? It was some strong stuff, took me almost 3 quarts of paint stripper and way to many hours of work.

Im still having a mental block trying to think up some ORIGINAL ideas to pull off the Battlefield look. I figure I will throw on some rust and keep all of the dings in the case to help it along. I could use any suggestions if you have some. (normally I am not this questioning/needing ideas from others I just cant figure this one out.)

Thanks again for the replies, it makes the forums worth coming back too.

-Do you think this should go under the worklog threads? I seem to be updating my mod for then asking questions lol!

A stealthed cd rom drive would be cool but the only proble is the area where i would have to stealth. It is quite curved and has a few other obsticles like the motherboard. I only have a 1 3/4 inch gap between the cdrom drive and the side panel. That means I have to fit the motherboard tray and the motherboard in that gap with some room to spare for the power and led connections.

Heres some pics

Do you think I have enough room for all of that?

Heres a pic of the back plate that is still onder constuction. I also have to add the back door on.

Well I have decided to start up this project again sence I have som tax money:twisted: (thank you federal government.) I dont have the pics for the missing images so Ill try to post some newones asap.

Just to recap on what has been done:
-Pain..,, I mean paint removed (alot of work i might add):dead:
-The rear and front doors cut and remounted.
- ahh.. I guess thats it lol.

A|Ill add some pics later tomorrow to show where im at.

Dan The Geek

Admin: feel free to move this to works in progrees if needed.

Here are the pics Crimson. lol

These are of my design I did in sketchup almost 6 months ago. It has a removable frame from the back(almost like a removable MB tray but everything comes out except the power and accessory buttons, front fan, and DVD ROM.

Ill take some pics of the actual case later and try to post them to show my progress. Thanx for viewing

Dan The Geek

Here are the pics as promissed. I had to borrow a camera, my olo one was acting up. Oh well.

The case looks very scratched up but it is just the flash. I also want to note that the crome molding will be sanded and painted. Its not on atached well either, just a little glue, but It will get the royal treatment on the final attachment. It will also follow the edges of the case more evenly.

Thanks agiain
Dan The Geek

Well I plan on using the top as an access to the parts on the inside. I hope to have the motherboard tray removable by only a couple screws but we well see:rolleyes: .

As for the rear vents for the PSU and FAN... Im not sure lol. I did plan on drilling a few holes in the rear door and the bottom and top of the door is open to allow for exhaust. Besides that Im not sure. Any suggestions would be cool.

Thanx for the comments, I love the look of the BIG rivets, almost tank like in person. The molding will be sanded and painted the color of the case. I will probably flatten it a little more so its not quite as rounded, and it will deffinetly follow the lines of the case( I like crisp edges.)

Well it looks like monday will be the day to start this agin. I hope to build most of the inner frame then.

Thanx again, Dan The Geek

Oh almost forgot, I did a little more tweaking with my sketchup and decided a full atx MB is a must. This also shows how all the doors should work when finished.

How do I move this to works in progress?