Looking great! Your hard work is even more evident the closer this project gets to completion.
Printable View
Looking great! Your hard work is even more evident the closer this project gets to completion.
Thanks MainMan :) I'm currently considering starting on the sleeving & wow I'm hoping it's not as difficult as many say it is lol :crossed::D.Quote:
Originally Posted by TheMainMan
Nah it's not bad. Just make sure to use a hot knife to cut it, or melt the ends with something to keep them from fraying. Also, make sure to cut MORE than you need, as when it expands it shrinks. I usually sleeve the wire, then cut to length as needed. Also, don't forget to put your heatshrink on BEFORE you crimp the connectors on :D
Something you learned the hard way, SXR?
/\This...very much, this... :facepalm:Quote:
Originally Posted by SXRguyinMA
Yes, just check out the sleeving I did on my Red Comet project (link in my sig)Quote:
Originally Posted by AmEv
yes :facepalm:Quote:
Originally Posted by x88x
Thanks for the tips SXRguyinMA :):up:.Quote:
Originally Posted by SXRguyinMA
:DQuote:
Originally Posted by AmEv
:DQuote:
Originally Posted by x88x
Noted :):up:.Quote:
Originally Posted by SXRguyinMA
I've heared the psu I'm going to sleeve (corsair ax850w) is a nightmare to do, but I'll move forward & find out for myself :D.
OK time for some MDPC sleeving :D.
Being new to a full on sleeving job, a quick google her a quick goolgle there & BAM.
How to remove an ATX plug
http://forums.bit-tech.net/showthread.php?t=64632
Snipped the heatshrink, cable tie & sleeving off the corsair ax850 atx cable.
Then went & gathered pliers, wire stripper, the crimping tool I got from MDPC in all it's matt black glory :D & my ridiculasly huge disposable lighter my bro bought me for christmas & isn't even half way used since christmas lol :D.
Got a paper clip straightened out & tried using it but was too thick soooo, I took it to the garage, snipped it in half & grinded it so it was nice & thin.
Tested it & it does the job of removing pins awesome, instead of pressing it against the ground I held it tight in the pliers to push it the extra needed amount, first attempt & it came out perfectly, so so much for this psu being difficult hehe :D, still though I'll need to dig out an exacto blade so I can heat it up to cut the sleeving well.
Nils awesome trademark custom cartoon picture :D.
40 metres of black sleeving for single wires & I think 10 metres of sata sleeving too, 150 pre-cut heatshrink pieces, a nice length of heatshrink, a pile of pins, a load of cable clip pieces of all the available sizes, enough sata power pass through pieces & a few sata power end pieces, that is all I think :D.
I might only do the CPU cable & the ATX cable tonight but it's on :):up:.
For heating the heatshrink, I would highly recommend picking up a heatgun (or a hair dryer would work too) instead of using the lighter. With a lighter you run a much higher risk of heating the tubing too much or even catching it on fire, plus you're limited in the range of movement that you can use it it. IE, only underneath or maybe to the side of the tubing, whereas with a heatgun you can attack it from any angle, and you can be much more precise in the amount of heat you convey. Plus, the heatgun will force the air into any little nooks and crannies and between wires, getting into those tight spots that you just can't reach with a lighter.
Luckily I have the option of both :), it's just that with the sleeving pack it said best results with a lighter by sweeping it past carefully, but it may have said that for those without a heatgun.Quote:
Originally Posted by x88x
I have used a heatgun for a light bit of sleeving & it burnt the sleeving but then again I wasn't using the correct size heatshrink :facepalm: anyway I brought the heatgun over also so I can find out which works best, thanks for mentioning though 88 :):up:.
