Unit 4

some cutting

toothpick making

looks like this

this is a connecting panel, because the front is removable, but there are still buttons need to connect,so.. oh well just wait until the next update *is too lazy to translate -.-* :santa:
and some bondoing

IM BAAAAAAAAAACK

colorizing the pump tower

grey.

shall be rusty but didnt came out good :(

...:dead::dead::dead:

but at least my switch power adapter removal thing works

IT WORKS !!!! :D

circle has 5 cm diameter till the end of the 8 edge 1.25, i need 4 of em

circle has 5 cm diameter till the end of the 8 edge 1.70, i need 2 of em

spray those 8 edge things on the mdf

after A LOT of filing

some more filing

and then i made those holes bigger with teh trusty dremel from hell 8)

final position

fixing my stupid mp3 player output

drawed on some 2x2cm squares

who who who the **** needs a scrollsaw? :D :D

after sawing a mess of fake snow

those squares will become the connectors for my new |nq|res
while the gue is drying i startet my milldesk

then i recived my acrylic tubes big thanks to squelsh :smoker:

glued

drilled a hole and taped it

8) 8) 8)

my milling desk is almost done 8)

dremel milling head

some milling but not filed or sanded, just to get the feeling

..s all :santa:

testbuild frommy geiger counter which will be controlled by the caselight circuit

this is the video

Quote:

---

Originally Posted by rerkin88

i like the work u've done so far.

Where in Germany Are you from dude?/

---

im from "baden württemberg" near tthe big town "heidelberg" which is actually bout 40 km from squelsh :D
anyways update time
filed the button holes square

then i tried to sand squelsh's res even, because he removed it with "aimed kicks from a junk part" :D try 1

well i diddnt took a pictur of it, but it aint worked, so i grabbed 40 grit and sanded it with it freehand while it spins in the drill 8)
the floor, 2mm acrylic

scrollsaw cutting :D

and glued toghether

while the glue was drying i solved the problem with the chimney

i removed quiet a bit to much material but hell, i dont care, it works :D

8)

these are the old res connectors, full with silicone and stuff
before

and after

polishing ownZ :D

sanding the res

starting with the acrylic rod

EFX designing

i think you all know what dis iz

8)

some designs

this is the reason why i take pics with my mobile phone, our cam is so

without the flash

my personal favorite

a bit too big

look, my button connector things are done

this is my lock valve

drilled some holes, some cutting,sanding etc...

attached that rubber stuff on the front

now i made some material piles

after miling

another pile

dOone

makro

and dont forget the core area

same here LOL

done

sketched the grahpite moderators

after miling

and the other part

I need an improvement for the floor because it was 2 even

shall be like dis

oh its broken :(

mmmmmmmmmmakrOOO

so wuz teh front part

look at dis PILE Oo

and some money shots

and last but not least..overall 8)

modding my mp3 player :banana:

this is what shall be done today, a big thing..dunno lol, contains some kind of mutant potato, located at the X18 Labs

and this wall mounted control panel

first of, cut out a block

after some miling we got this :)

this wuz a very helpful tool \m/ 8)

miling done

because it wouldn't work with the pipe i milled a circular hole in the back housing

the pipe: overhead foil

cutted to size

bam

miling a cap

not that round but its fine

done

compare to the sketch

some more circles

milled a ring outa it

and some holders

and a kewlish cable

*gg*

mutant potato baby

final place

coffee time.. i wuz up there bout an hour too long, but i just cant got up

uh well, finally back at work, miled these

final place

s all :santa:

LOL..strelok is a mutant potato

dis is the mutant potato housing ill build

and this is why its called mutant potato :D

render shots of mutant potato aka the united thinking think (oO)

strelok you mutant :p

almost done

sup @ll.. thanks for the comments :)
first of, some work on the chimney

attached

a block of concrete

well the mutant potato thing is done :)

s all :santa:

yay.. modding suplies :)
black debris

grey debris

brown pigments

and green ones

handlebars

glue and paint brushes

stairs.. sadly wayy to small.. maybe i can use them for some kitbashing

acrylic rods.. 2,4,6 mm diameter

check out THAT SIZE LOL :D

black solid plexi.. i thought its tinted..no its just plain black :(

see ya on saturday :)

small update today.. busy shiz in school :( .. but anyways, TO you have my respect.. making thoes efx things is such a hard shijz :(
uh well,, i think everyone of you uses tape to mask of acrylic... i used glue and paper because i ran out of tape (almost ;) ) (glued it on the protective film ;))

fibreglass work was needed..

safety first xD :D oO 8)

yeah this is when i ran out of hardener :( those white areas are not soaked fibreglass.. i hope i can continue tomorrow

s all :)

some more work on the PSU tower :dead:

"some" bondo

while the bondo was drying i drawed an PSU backplate

puzzle in a different way

makro

...bondo & sanding...

some of those parts you dont wanna show.. but i needed to because it is just worse.. some fixing is needed here

as you can see, stil far from being done :/

sunday :dead:

this
a) sucks b) need some time to look like i want :dead:
yesterday.elektronics arrived, im to sick to solder so i cleaned up the soldertable :dead:
before

and after

toolZ

wires

stuff

this is the electronic madness which will be inside unit 4

a video

:D

ya... lol ... the video is actually a teaser for the movie ill gonna make when im off to the german casemodding masters (did it also with the old case last year) the guys on a forum really liked the movie so i decided to make a teaser for the one this year(cuz the old case has birthday today lol)and yeah the guy.. hes a friend of mine also modder.. and his birthday is at 20th and i started building this case on the 20th so^^

and a big YAYmy leds arrived

10 red
10 green
10 white
10 uv
with heat shrinkin and resistors .. soo cooooooool i think ill go to bed now, tomorrow ill visit my mom and print out the circuits so i can etch em :)

hi, i used adobe after effects and sony vegas for the video, but anyways update time :D

PCB WORK

yeah i make my on circuits and etch em. with a laser printer and a iron

after ironing the printed circuit on the pcb i need to remove the paper

this is what it looks like then

the mega led fader (100+)

actually its tribaloverkills fault that i made this :D

cutted

goddam small $#!t

after ironing and removing.. SICK!!!!

etching fluid

while etching

afet 15 minutes i recognized that the pcbs where still the same, so i took my um.. dryer which makes air pretty D*#n hot :O s the fluid has a higher temp and its moved so it etches WAY faster

i must say.. this method PWNS!!!!!1111oneoneone the pcb was done after 7 minutes

and always think of THIS COULD BE YOUR SKIN! so wear ALWAYS GLOVES! its.. acidly

and bÄm

then i need some holes

:D :D :D

yeah.. here you can see how big this thing is :O

so the pump control is done :)

it does work.. at least i _think_ it does.. the relai works and thats all what it has to do

update time!!!!1111oneoneoneeleven
another hole

which is wayyy better than the old one :rolleyes:

now i need to close that opening

taped
and again, fibreglass :rolleyes: :D

miled the led holes

epic makro failure

cablechannel
aim

and bOOm pushbuttons insertet

dis is how it looks like from teh inside

the fibreglass is also dry

and smoooooooooth

got wires?

GIMME A HELL YEAH!!!!

my christmas gift :)

another update

this groove is for a wire, so i can hock those steel support wires in, just like in the real build

mounted the cd cover(which needs some new tiles

and the old hdd cage is mounted (need some kitbash)

quick inside overview

and the pushbutton terminal is mounted also

time to mill

action shot :O

and the finished part

this should be some kind of mega fuse construction, one of em is broken

led wire channel was milled

this is how it should look like, except the cap of the real fuse wont be visible in the finished part

_some_ wires

..and a happy new year

whoa update time Oo this is the awfull picture of my workshop

expand the pc

this is a quick dual external harddrive "mod"

sanded

polish stuff

and polished(beta ;))

this is what it roughly looks like, the old cd drive will house the circuit stuff and maybe something more^^

some kitbashing is needed and some (or alot) paint (will be flat black)

anyways real update, 2 cutting disks

cutted a channel

in there will run the wires for the led, and some space for the resistors oO

:D

red :)

GIMME A HELL YEAH!!!!!!!!! WOHOOOOOOO
i present: effective LED lighting how its be in the case 8)

the only difference between the pics is the shutter time :)

whatcha think shall i stay @ 800x600 or go back to my 640x480?

i have no invitation yet, but i know the registration is soon

the PSU FITS!(what a pain it was :dead: )

psuhbutton size increasing things (oO) made outta foam

and now HOW TO GET COOL BULLET HOLES IN MESH
first, measure the size of the entire mesh part you need

then, cut out and mark the parts youll see later, then draw on the holes

right after that youll take something round, eg a roundfile, position it above a hole and do the dew :D

finally take a drillbit or something ells to increase the size of the holes

should look like this now

and back in

and the finish with a cool handlebar :D

this _was_ my final exam project for school, a slot machine

now, rip apart the circuit and the leds

shaky? yes.

anyways, got some sweet cable and 16 ultrabright yellow leds and some solderboard
here i tested the leds for the chimney, running 4 in a row with a 470 ohm resistor @ 12V (gotta drop the resistor somewhen)

some faking, the shutterspeed was bout a second

comments?^^

paintingsession

:think::think::think:

:eek::eek:

:smoker:

:redface:

8)

:eek::eek:

:lick:

:santa::santa:

:twisted:

:D:D

:up:

:devious:

:D :rolleyes: :dead:

:alien:

and yet, a word :D the res is almost done (but not waterproof :evil: )

WEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEE

:banana::banana::banana::banana::banana:

ITS LEAK PROOF, MY FIRST WATERCOOLING SET EVER IS LEAK PROOF WOOOOOOOOO

some temp shots

filled with oridinary water and cranked up the pump

drainspot <3

feser fluid <33

ohhhhhhh lights

:banana::banana::banana:

bought some screws

the core is officially DONE

sorry for the blurry pics, gonna take some more tomorrow

weeeee

covered those holes

support for the frontpanelplug

:)

compare to a midisized cardboard boxing

monolith stage painted

paint to the people
white basecoat

and finished drybrush

somewhat the monolith looks sooo crappy, gonna redo this Mofo

:)

:banana::banana:UPDATES! :banana::banana:
made some holders out of foam for the pump control

then, i milled this air vent thing

should look like this when its done

the top got smashed also :D

glued 2 fans together

some painting

also inside

glued on the foamholders for the pump control

made a cd drive cover

and some new improved fanholders

and then throw everything in there and take some pics

and the fuse thingy

and the monolith surrounding thingy

and the pushbutton- things oO

yo :)

paint outside

these should look like some kind of seam

covered the switchpanel

white basecoat on the supports

under the ducttape..

some drybrush (way to big if you imagine that the gab between the black bars is ~2m in real life)

support painted

this screw

holds this sandblast thing, the camera was on the same position, just some zoom

fanholder v. 2

some miling, sanding and drilling

attached the fans

thats all

a hole for the fancable

milled a channel to run the wires in

and a good ol drinking yar made the pipejob

the rest of the day took the chimney (i hate this thing now)

looks a bit weird, because its like 3/4 done yet

drybrush shot

and the gabs

started with a fan frame

and also covered that hole

i iz seeing big thingz

ITS DONE O.o

quick update of primer

and also the inside

and this molex connector is needed to create some kind of master power line

and thats ma new monitor(without colorsetting)

maybe i can post another update in some hours ( if i can drag me away from this sweetnes)