Printable View
Hey guys,
I think I may have killed my computer... I just swapped in a new CPU. and upon reassembly I pushed the power button and the CPU fan turns on, the power light and HDD light turn on, and the LED on the Mobo turns on but I get no video or any HDD noise. Is there anything I can try to do to fix it or is it dead?
I have tried removing and reseating all the connections, Memory modules, etc but still no result.
BTW its a Dell Dimension 2400.
Hmmm, what's the PSU and what's the new CPU? It sounds like the PSU might not be able to power it. Is there a system speaker attached? That should give you some info if it's the RAM.
EDIT:
Also, try dropping the old CPU in; if it works fine with the old CPU, the PSU is definitely the problem.
What kind of CPU? Could be a compatibility issue if, for example, you drop a multicore 775 CPU in an older 775 socket that doesn't support multicores you'd get power but no POST as well. Definitely try the old CPU again, but more info is necessary.
Make sure everything is plugged in. I forgot the 4/8 pin CPU power connector once and experienced similar results.
You beat me to it, Lothair!
It could also be that you need a BIOS update to support the new CPU.Quote:
Originally Posted by mDust
The new CPU is a Celeron 2.6ghz, when I put the old CPU back in it started right up. Is there any other way of testing the CPU?
Whats the new cpu? Also most dells have a series of post indicatior lights labledd 1 2 3 4 on them. Do these light and if so where do they stall out at with the new cpu installed?
For the most part receiving a bad cpu of any sort is a very very rare occurance, I'd guess its what alot of other folks have already said, bad mobo bios or not enough wattage to run the new cpu. In the case of dell they ship with crap power supplies, when I was working for MGM Mirage we would have 20-30 of them out with bad power sups at any given time.
As for what to do to figure it out... it all depends on what sort of resources you have to work with. If you have another 775 based system to test with it would work wonders for troubleshooting.
If the CPU is bad it shouldn't do anything at all when you put power to it, so I'm putting my money on a wimpy PSU. Do you have another PSU you could try? If not, that model takes a standard ATX PSU, so you could pick up a decent lower-power PSU for ~$40. Here's a couple. 350W will be more than enough as long as you get a quality unit.Quote:
Originally Posted by chevyboy_0
http://www.newegg.com/Product/Produc...82E16817371033
http://www.newegg.com/Product/Produc...82E16817151077
Ooh, or this one if you catch it in time.
http://www.newegg.com/Product/Produc...82E16817371034
Some of those PSUs (Delta-built - the Hipros weren't quite as good) were solid enough, although it's worth trying a different one. I've only seen one fail out of the dozen or so I've dealt with, though that doesn't say much. I'm inclined to say that the PSU's good since it works with the old CPU, though you never know.
To elaborate: This probably isn't it, but is your new Celeron a Northwood or Prescott core (128k or 256k L2)? If it's actually a 2.6 GHz (even-numbered) then it's a Northwood and apparently should work; if it's actually a 2.53 or 2.67, it's actually a Celeron D and probably won't be supported, at least without a BIOS update if not a physical alteration of the board/CPU (a quick Googling led me here, which is discouraging). You say it's a 2.6, though, so I'm inclined to rule that one out, though I have to ask 'cos of your sig.Quote:
Originally Posted by mDust
Thanks for all the replies fellas. Because of my busy work schedule(were trying to finish painting a Chevelle) I havent had to much time to really play around with it.
After looking at it again it does turn out that it is a 2.66ghz Celeron D, which I believe is the Prescott. oh well it was a $7 mistake. On that dell website it says there is a way to make it compatible but through the use of a microPCB board. I guess I'll just have to grin and bare it until my new rig is finished. ;)