Hp Res 3 Mega

Hi guys :) Ive lurked here for a lil while and im totally impressed by the qual of thr mods here :)

ive just posted my last finished case "HPRes II" over in the project galleries.


This is HP Res III Mega, im trying to take what i did with HPR2 a few steps further.

most of the mods on this case will revolve around bondo work to the case.
once again the whole job will be finished in 2pack auto and have my signature side mounted water tank/s :)

I'm still not 100% on what the end outcome will be or how soon i can finish this mod, but will be fun to share it here with you guys :)

the original case

Making thr MEGA blowhole

New filler panel and adding some bondo

alota sanding :)

a lot more sanding!

More bondo and more sanding!!!!!

some final work and a lota high fill :)

( 2 weeks later!)

A dust coat and final wetub

One MEGA blow hole :)

more to come :)

Can't wait!

r u an hp modding employee promoting the capabilities of their cases in the community? :D excellent job on the blowhole.

Excellent - this to me is modding - getting great and imaginative ideas to fruition...........just don't know where you find the time.

Keeping it coming as the final result looked awesome...............

very nice. only question i have is, "how are you gonna access the drives." guess im just gonna have to stay tuned.

see up the top in the first pic... how its a door...
he just extended that up to be full size, instead of 1 bay to short.

Just don't drop that bezel :D

The only thing I hate about bondo is how easy it breaks :(

that looks nice man good job so far

thanx guys :) a bit more work done, this time to the MB side panel,

again HPR3 will have a side mounted res, the side pansl is modded to suit the theme :)

I've cut some strip of plex these can be bent to shape for the edges.

using a bit of heat the strips of plex bend to shap with little effort.

not too hard.

ive decided to "groove" tenches around the walls, this will give a lower area for the bondo to bite down and sand back level.

a qik re-sand on the groved areas

same with the back

next is to sit the side walls back in and use some hot glue to hold it all in place.

Next is a qik "fitup" test, i a big fan of the fitup test :)

all fits good :)

after the initial sand back i could see on the bottem edge of the side hole the bondo wasnt sticking :(

i didnt prep clean proper...... a few holes to act as "anchor points" will fix that.

and some fresh bondo

Some more sanding, using an old peice of plastic pipe i can wrap some 60G around it and sand the shape needed.

Starting to take shape :)

that looks sweet man. the style is very recognizable after your other mod.

Very nice. I've never worked with bondo, or anything similar to it, but what your doing sure makes me want to try. :)

Just make sure you use it in small space with little air circulation. Then you will get the best effects of bondo ;)

:eek: :eek: :eek: :eek:


Looks freaking amazing.

thank you guys :)


smallish update guys :)

this is all early fab stuff atm, so it all looks a bit ruff.

the custom fan box will be shaped bondoed and painted, the front blow hole insert panel isn't final either, but gives you an idea of the look in after.

trying some mesh from insde an old apple tube mon!

sweet

That's pretty sharp looking. Is that internal bezel in the blow hole going to be flat like that or are you going to give it some shape? Maybe a simple ogee profile or something to give it some character? Of course, that would mean more Bondo work. ;)

Holy Cow! manyour mods are so awesome. You have inspired me to try that bondo stuff for one of my case mods. :D

cheers guys, the front bezel sits off the mesh and allows air flow around the edges,

i did think of giving it an edge!!! very much like the side res panel and the mega hole itself.

ive started on a second and 3 peice already, the options so far are to keep it flat have writing or a logo laser cut into it so it backlights thru the lettering,

as you said have a raised lip around the edge of the insert. or to have it sightly convexed with a rounded shape to it.

the front pansl also had to hold a back light and more than likley a power buttom of some sort.

What type of glue or bonding material do you use on that plastic to keep it together?

Holy Crap that's Hot!--I must have been under a rock to miss this project. Can't wait to see more

U got that right, lol.
I love those two horizontal accent pieces you used too, just above the megablow hole... they really add to the curved aspect of the front of the case.
Its the small details which make the big picture!

Defyant = Crim under different name

Wow, that is looking fantastic. I am looking forward to seeing this.

Have you thought about putting a bubbler in the front of the mega blowhole because the blue light diffused through bubbles would be awesome. All I'm thinking is two peices of thin 3mm perspex, sealed with water inside and a small air pump set up. You could even put some of that uv reactive solution into the water for extra glowy goodness, you could even set it up so that you can turn off the blue lighting and have a 'stealth' black light so that just the water glows. Maybe a bit ambitious, but I'm sure that you could do it. :)

shoosh! that was gonna be part of my cryogen mod! sept i dont have the money :(

Oh man...yeah...the bondo work on this just makes me want to go buy some...never used it but they way it finishes looks down right amazing. Time to visit the hard ware store today.

Seen this around and still love seeing it around. excellent work

thanx guys :)


got a few hours tonight so i knocked over the fanbox,


first off was to knock all the edges off using sowe 60g

counter sink the holes, better to do this now before the bondo hits!

cut some stips of flexable plastic, im using these as the guides an they will simply peel away @ the end.

post 2

Bondo time!!!!

i want to add small blow hole lips to keep with the theme inside and out.

First of 3 layers of bondo.

starting to take shape

after another bondo and rub.

peel the plasitc guides away

a qik rub on the iners

redrill the screw holes

finally some spray putty,

so far so good :)


will wet rub this in a few days-to a week, then another sprey with putty before paint.

Wow...now that is some amazing stuff...i mean...I thought the box looked fine as plexy...but thats flat out amazing.

Very nice work with the bondo. This case will look very nice when its done.

it looks pretty cool. i wonder how much the mesh and that extra oval plate in front of the fans will restrict the airflow. or maybe im just too picky about restrictive blowholes? :D

it will restrict a bit, but the dual blow hole only serves the purpose to deliver enuf air to supply one rear mounted 120bix!, even with the middle plate it will still supply enuf air to do that


theres still the side panel to be done :D

Didn't want to run the old metal back plate, so i thought i'd try something different. :D
Stepping out to my favorite shop, i picked up a cut peice of 8mm thick clear plex!

A qik test to see it fits right, all the motherboard points and needed holes, mounts etc will be added later.

The plex panel it self isn't the actual mod! but the idea to diffuse and light it is!

the idea came to me while doing the front light diffusers, its just going to be on a much larger scale.

A qik test on a small peice of off-cut confirms the idea will work.

next is to sand the peice of plex with 1200 wet and dry, the small scratched catch the light beem and allow the whole flat surface to light, rather then just letting the light travel thru to the ends like on Hevy plex SLB mod i did for Zak.

Adding some light.

Once i could see that the effect was goin to work it was time to peel off the protective paper and get to work on my motherboard back panel.


Simple wetrub in the laundry sink again with 1200 W/D and a 3M rubber hand block, all of 15 mins work and is done to both sides to achive an almost frosted look.

The end result.

Next is to hook up some lights for testing.

turn off the lights and see if it works!

i was pretty impressed at what a great internal light feature this simple mod makes,even with the motherboard and internal bolted in there will still be enuf see-able area to keep this a main feature inside the case.

keep it coming. excellent job again

Looking really good.

Like the way things are lighing up for you :)

Wonderful work, Keep it up.

Couple questions, what are the LED's in and how did you attach that to the plexi?

Looks like a set of Lazer LED's, i'm assuming that mounting is temporary though, as the lights will need to be inside the case.

yer thats it guys just a old set of lazer's in a temp placing to test.

i do use a slip on type as well, Defyant style flex light leeds, like on HP1 and a diff setup i used on my sons MOD Hevy plex SLB.

This is the variant i made for my sons case mod.

These plug into a baybus for a "modular lighting" setup

Then plug into his plex side panels for this effect.