Water Alien Rebirth

[pedrofilho]

The project is going faster now. This week i'll finish the front panel and do some paint and mounting works.

Today most updates:

To fill...

To cut...

To measurements and suport...

Plexi to front panel

Piece cuted and marked

Frontal panel works:

Screcth on V to makes easly de folding it...

To cut the groove

The roof will act with front panel, so i've to cut and do a small test. rs. before cutting the front panel...

After this cut i tested the idea and works, so, keep cuting the front panel...

It's expensive, must use all that...

Groove cuted, it works..

Tomorrow i'll do a finishing job on this, fits perfectly, loved it...

Tomorrow i'll finish this and do other things.

I am really tired, have not to say, started to soon today and don't stop until now.

See you tomorrow, i'm exausted... Today was a great day, did a lot of advances, tomorrow i'll do more... Hope !

Thank you,

Pedro Torres.

[pedrofilho]

great work pedro, I realy like what you are doing with the front panel

I brought some news about that, right now...

Thanks

Nice man i Really like it. I spent about 20 minutes reading the whole thread lol.

It's really have a lot of posts already... Nice reading.

Be wellcome !

Firsts results with front panel:

Have a Dremel nylon disk that may work to do a polishing job on corners, to get a better tranparency...

Will close up and down with plexi and put a hinge pair in left side:

See you later !

Pedro Torres.

[pedrofilho]

very nice update pedro, i rely love this work log!

+REP

Thank you GT40_GearHead,

Today i did some modifications on original idea to front panel, because i do not like the visual that came out before. So, i did it another time, and, now it pop up as i expected... Liked it !

Thanks for beeing here, you're wellcome !

You are doing some awesome work Pedro, keep it up dude!

Thank you jbdnsn, be sure i am trying to do always the best i can, to share with friends like you.

Thanks.

Now the news...

I did another front panel to show better the hot stuff i'll put on 5 1/4 bays. Two of then are CM stuff, a cooldrive 6 and a cooldrive 5, and a vantec nexus to cpu, with usb e firewire conectors... Beautifull... Also, it will show the 3 vandal switch when i install it...

Let's go to photos..

The metod

Have to use gloves, so you don't get burned... ouch !

Anoying white stuff...

Now what?! I really like as this come out this time ! Clean and precise. Tomorrow i'll do a finishing job...

I'll do all i can to mount the case until 17.02.2007 because there is another contest i want to participate. And until the end of the year it will got some improvements to CM 2007 WW contest, the final goal of this Expensive, hardwork and delicious project...

See you tomorrow with more pretty news, until thursday some pieces will arrive here... Nice stuff...

Pedro Torres.

[pedrofilho]

Today i got my Dremel D-Vise from the customs. They stay with it since december and set it free just yesterday... I really miss this tool, but, now i got it !

See you later with today's mods.

Thank you !

Pedro Torres.

[pedrofilho]

Looking great Pedro. Really can't wait to see this mod running. Crackin!!

Soon as february 17. this day is the last day to subscrive on a Dremel contest here... After that i'll do some finishings, until the CM WW contest on the end of the year

Thank you !

Wow. Can't wait to see the end result!

It's near, hold on... I want it mounted february 17 and tomorrow i'll do a hard sanding job to paint all internal pieces until the weekend when i'll start some exterior textures.

Thank you !

Some work i did today is preparation to others.

This is how i intend to mount the Alien vs. Predator playset, over a iluminated black plaxi plate engraved... (wow)

This is the cut i'll use as the playset base:

As i intent to engrave over black paint, i did it today, to do the engraving job on next week, when the paint will be totaly dry to suport the work with minimal secondary damages.

Well, tomorrow i'll sand some pieces, so, i prepared some parts to do an one time job...

See you folks.

Pedro Torres.

[pedrofilho]

Do not resist, this is the way it will be on case. With a small elevation. The paint job pop up explendid. I'll wait it dry completly next week to do the engraving work.

See you tomorrow,

Pedro Torres.

BTW-> I'll apreciate sugestions about the figure i must engrave on this alien vs. predator base. Anything like an alien texture or hierogliplhos, things like that... Thanks.

[pedrofilho]

Just started the sanding job and those toys arrived to stop the works...

Later i'll put some photos e also when mount then.

This Cooldrive 5 is a beautifull dream... Amazing...

This items are the reason to transparent front panel, i could't hide this things, they're really nice.

See you later,

Pedro Torres.

[pedrofilho]

Noice.
/subscribed
+rep

Thank you for your support.

As i promess, more work and a lot of photos:

Side windows ready for texturing:

Powerfull 10mm UV Leds to case feet:

I'll sand more tomorrow, the base is not good:

Have to do some finishing works with Dremel before sanding...

Front panel is ready for paint:

Toys:

A lot of acessories and extras

Really nice extra fronts i won as gift from a brazilian casemod store!

The photos do not reveal all the colors and bright of these items, they're really beautifull stuff ! Hope get better photos when mount the case at daylight !

Thank You !

Pedro Torres.

[pedrofilho]

pedro if ure looking for 470ohm resistors i just bought about 1k of em from best hong kong ill be more then willing to ship em to ya if u pay for shipping
btw what are the specs on the 10mm's u got i got 10 prewired 12v uv leds as well except they dont excite the uv paint

overall this thing is comin out wonderfully gj man


-ben

Ben,

I really apreciate your offer, but, i've already bought all resistors i'll need to leds.

Thank you very much !

Most of today's work was sanding and polishing job...

Paint to see all defective points

And i locate a lot of them

Got a hard work today and tomorrow i'll do a paint job on this case !

Thank you !

Pedro Torres.

[pedrofilho]

Fall from bed...

Could't resist to bring the news about front panel paintings....

It's pop up fantastic, trully amazing... Now i fully believe on spray paints, whata !

Those fotos i've got last night and still are not good enough. When sun come out i'll take better shots...

Now i'm going to do a paint job on that case. Whe stores open around here, i'll buy more sands...

See you later with big huge news...

Pedro Torres.