-
Anodized
Zodiac
I've been a long time lurker... I haven't completed a project I felt was post worthy until now, so I decided to register and share it with you all.
This mod has already been completed. It was my entry into a case mod competition on another forum. I recently switched the GPU out to an HD4870, and so will be changing the color scheme and adding quite a bit to the aesthetics. If figured that I would post the entire original log first, and then continue the rebuild from there.
Lots of changes have happened throughout this mod, but I decided to leave all of the original pics attached for a more natural progression. If you see something missing in a later photo, it likely got axed.
I'm not going to clutter the the first post with a whole bunch of stock
rocketfish pics, if you aren't sure what they look like, or would like
a bit of history relating to the "famous" rocketfish case, just type
"rocketfish" in the search.
So, lets jump right in.
System specs:
E4600
Gigabyte P35-DS3L
EVGA 9800GTX
4Gb G.skill
WD 250Gb SE16
Sony/NEC DVD-RW
PC Power & Cooling Silencer 610
DDC3.2/MCP355 w/XSPC top
Swiftech MCR320
CPU GPU cooling- custom waterblocks
Here is my case with the front door and floppy bay removed. I also
removed the USB/headphone jacks from the top of the case. I am going
to switch that PSU out for a PCP&C version because it has two PCIE
connectors.
Since the 3.5 bay is gone, I'm going to remove a section to help
with ventilation.
The same section needs to be removed from the inner front panel.
Also seen here, Pnuematic nibbler and the "belt sander gun" as I
like to call it. Modder's best friends. Invest in these puppies,
and cutting window/radiator holes will turn from minutes into seconds.
I am very grateful that I have access to this equipment at my work, and
that my boss is generous enough to let me use it.
After cutting. You can see I didn't do a perfect job but it won't matter
in this case.
Some mesh added to the hole
I made up a nice little aluminum grille for the inner front panel
using the punch and shear(the two will be pictured later).
There is a bracket between the hard drives and motherboard tray that
adds quite a bit of strength to the case. I want to make a nice divider,
but still retain this feature some way.
Here is the aluminum sheet sheared to size and drilled out for some
UV Leds. You can see the bend lines marked in red.
Here is the metal about to be bent on the brake.
Perfect fit! I love it when that happens, especially because screwing
up means buying more metal.
I hot-glued the UV Leds in the holes on the back of the cover, and wired
them up with a molex connector.
Testing.
I was going for the clean look, I think it turned out pretty well.
I used the same mounting holes as the previous bracket to hold in the
so the cover ends up handily serving a dual-purpose.
-
Anodized
-
Anodized
Re: Project: Zodiac
If you look at the second to last picture in the previous post,
you can see the rectangular hole I nibbled out in the top front of the case.
It will contain a control panel with the relocated power buttons and
a slightly chopped Scythe Kaze Master fan controller. This is the display after programming the CNC:
I sheared the plate with the angle cuts, and then clamped it into the vise
for machining. This is after a quick beadblast; I'm just about to engrave
the labels for the buttons and knobs.
After engraving and another light beadblast.
I machined a bit out from the back of the power and reset button tabs to make them a
little more flexible.
After painting; I rather like the way this turned out.
Here's a whole bunch of shots:
With the lights on:
The "HDD" label in the control panel will have a small hole drilled above it for a small
piece of fiber optic leading to an LED. I will detail that later in the worklog, along with pictures
of how I mounted the Kaze master.
-
Anodized
Re: Project: Zodiac
BIG CHANGES
So, first off, I need to update the system specs.
-The E4600 was switched out for an E7200
-Gigabyte P35 DS3L switched for DFI Lanparty P35 Dark
-G.Skill switched out for 4gb OCZ Reaper HPC
I was busy for a couple weeks, and had some time to review the work I had already completed, and make plans for the rest of the build. I scrapped a few things, and replaced them with newer, better things.
The top power button/fan control panel is gone, and the 2 channel 3.5" Kaze master has been switched out for the 4-channel 5.25" version. Originall channel 1 was going to be the rad, and channel 2 was going to be the intake and exhaust fans.
Now it will be-
-Channel 1, radiator
-Ch 2, Front intake (Upper case section)
-Ch 3, Front intake (HDD/PSU bay)
-Ch 4, Rear exhaust
After deciding on my design changes, the first order of business was to remove those pesky 5.25" drive bays. Who needs em?
Since I removed the drive bays I'll need somewhere to put the DVD drive amirite? It will be hidden under an upper shroud that covers the radiator and DVD, which matches the lower shroud which covers the HDD's/PSU.
I used the same techniques shown earlier in the worklog for the lower shroud. Brake, shear, drill, mill, punch, etc. Show here is the mounting bracket for the DVD drive.
Mounting bracket installed.
Another view.
While I was working on measurements I set the CNC to work on a nice solid brass top for my DDC pump.
Hehe, sweetness.
Here are a couple pics I snapped after I got home (*not shown* I set the upper shoud up on the CNC and cut the fan/tubing holes for the rad):
This shows the location of the DVD drive.
Dayuum! That's a tight fit!
KITTY!
-
Anodized
Re: Project: Zodiac
Setting up the blank for the front trim panel on the CNC
While I was waiting for the part to come off the CNC I tore the case down and hot-glued some screen into the upper cover as a dust filter. You can also see in the back where I removed the stock grille area to make way for an access panel, this will (hopefully) allow me to better work on my loop without having to remove the radiator.
Part is done!
I mounted the two front intakes. I also removed the 2nd HDD bay to make room for the pump. In the front you can see where I modded the stock audio jacks from the top of the case into easy reach on the side. As you can see I am also working on the cable management.
Here's a close up with the wiring in place.
*Not Shown* I took the measurements for the Scythe 5.25" Kaze master and cut the appropriate holes, then stripped the fan controller down to the circuit board so I could stealth mount it.
Front trim panel w/fan controller after painting:
Here's some pics I took after I got home:
Kaze Master ablaze in all its glory.
Closeup of audio/USB jacks. I used a roper whitney hand punch to make the holes, and used the stock screws to attach the jacks through the panel.
Here's the first pic so far in the log with my new mobo/cpu/ram, and improved cable management. Looks pretty snazzy IMO.
-
Anodized
Re: Project: Zodiac
I ditched the old power control panel since I switched to the 5.25 kaze master, so here I am making up the new one...
After engraving
This is the back piece which holds the microswitches and acts as a clamp to hold the panel on...
Painted and mounted:
I started work on a copper mounting bracket for my apogee GT:
After machining, I used the punch, bandsaw, files, sander and scotchbrite pad to finish the bracket. Then I gave it a coat of clear matte protectant.
I figured while I was at it, might as well step the base too:
Perfecting the lap
Matte finish finally dried, so I assembled the block:
Getting the mounting bracket for the Apogee GT done was the last thing I needed to do so that I could install my loop. The pump hangs by its inlet from the bottom of the res, and it seems to have worked perfectly to kill the vibration. Not the prettiest thing, but who cares... you can't see that part anyways.
-
Anodized
Re: Project: Zodiac
Here's where I go a bit out of bounds:
I cut a piece of thin plywood to size with the bandsaw, and made cutouts for the sata connectors and power cable, then smoothed them with this little drum sander.
Here I marked and drilled a few notable constellations.
Wig making, case modding, it's all the same amirite?
Here's all the fibers glued in place and tied down. You can see the white LED illuminator bundle I made on the left. I filled up a piece of heatshrink with epoxy, and then jammed the LED's and Fiber optic bundle into each end, then heat cured it.
Back shot lit on the test bench
Front
Mars, Earth and Venus (aka Ping pong ball and round beads painted with UV paint)
I will attach them to the star panel using some epoxy and .035" welding wire, heres the supports for the Earth and the Moon.
Using the handy-dandy micro spot welder to attach the two:
Sweet.
I glued the wire in with epoxy, and painted it black with some flat black spray paint and a q-tip.
While I waited for the epoxy to cure, I started on a shroud for the reservoir. I ended up cutting the ears off because they ended up being ugly when it was all bent up.
Couple shots with the shroud in place and the planets attached:
-
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules