After spending the best part of 6 years learning many many things about PC tech and trends I have only recently broadened my view to the very wide world of audio devices.
Now I know I have no where near as much knowledge as Luke122 and the other Audiophiles on the forum but I thought I would piece together a tutorial on the first thing audio inspired I ever tried. Connecting my stereo to my PC.
First I will let you know a little about the different types of connections a PC and stereo may have.
Analog:
The most basic of connections, all PCs will have this.
(The small round sockets)
Digital (Coaxial):
A more advanced type of connection. Not all PCs will have this but if you have a sound card or a high end motherboard you should have access to this connection.
Digital (Optical):
Digital Optical is the best type of connection you can utilise. Not many PCs will support this type of connection as default but once again if you have a high end motherboard or a good sound card you should have access to this connection.
Now that we know a little bit about the connections available we need to check which types of connections are available to us via our PC and stereo.
As you can see my PC has both Analog and Digital Coaxial connections.
My stereo (Pioneer A390) only has an Analog connection which is labelled as “AUX”.
I was hoping to be able to use the Digital Coaxial connection for this but due to the lack of it on my stereo I will be attaching my PC to my stereo via an Analog connection.
What you will need:
RCA-3.5mm splitter
3.5mm extension cable with male plugs (size depending on distance between PC and stereo)
And a 3.5mm female-female adapter
First I plug my RCA-3.5mm splitter into the plugs labelled “AUX” on the rear of my stereo.
I then connected one end of the 3.5mm female-female adapter to the 3.5mm plug on the RCA-3.5mm splitter.
Then I connected one end of my 3.5mm extension cable to the other end of the 3.5mm female-female adapter.
Lastly I plugged the other end of the 3.5mm extension cable in to my PC via the rear left/right socket on my on-board sound card.
Depending on the orientation of your speakers you really can plug it into any of the sockets on your sound card (rear, side, front). I already have a set of front speakers and the orientation of my stereo speakers allows them to be used as rear speakers.
Once you have done all that you will need to let your PC know that new speakers have been installed. Some sound card drivers will auto detect when a speaker is plugged in and set it to the right channel. For some reason my DFI motherboard didn’t do this so I had to do it myself.
To do this I double clicked on the “Realtek HD Audio Manager” icon on my system tray.
(Sorry for the blurry pic)
This brings up a window allowing me to see what speakers are attached to my PC and allows me to mess around with their settings.
The first thing I had to do was change my speaker configuration from Stereo to Quadraphonic. The previous Stereo configuration only supports a set of front speakers where Quadraphonic supports front speakers along with rear speakers.
To make the change from Stereo to Quadraphonic I simply selected Quadraphonic from the drop down box labelled as “Speaker Configuration” on the left hand side of the window.
After I had selected the Quadraphonic setting from the drop down box I checked both the “Front Left and Right” and the “Surround Speakers” boxes found on the left hand side of the window under the drop down box.
I then applied these settings and shut down my PC. When I re-booted I turned on my stereo and changed the mode to “AUX” by pressing the button on the front.
I then fired up Songbird and enjoyed far superior sound then I had before.
Well that is the end of the Tutorial. If you have any questions or problems please post them here and I will try to help you as best I can.
Just for you out there wondering, the entire process cost me just under $12AUD (I had to get a bit extra speaker cable).
-Tb4o-