Just splendid work! And i love what you've done with the PSU, +rep for that!!
Thanks loki!
good news people! ITS ALIVE!!!
How it stands at the moment
Idle. Notice that the ram index score jumped from 5.5 to 7.5 by throwing these mushkin´s in!
Vantage score. I HAVE to get a new waterblock for this GPU.. Look at those vrm´s on gpu2 :wallbash:
And a 06 score
is that a 120.9 raddy on your case, or are you just happy to see me?
METO V.1
METO V.2
METO V.3
PC-Beto
Project M8 [WIP]
I think calling this case HUGE is an understatement. I love looking at a mod that is just CLEAN and crisp. Very nice work.
Thank you guys! This is part one, of a larger update that i decided to tear down into two, beacuse i cant finish the other part before a week or so
A little picture of the new mobo! Decided to get the EVGA p55 le, since its all black, and fits the theme best.
Also got the IQ panel painted.
And the backside of the Bitspower block. Still thinking of what to do with this
Another shot of backside, and card.
And the modded Aquacomputer cuplex kryos! Now in all black
And with a quite expensive fitting combo lol
Mounted on the mobo^
Also had to make some panels to finish up the rear of the case. So they were cut to size, and painted.
And i know, i know, "Dude, what happened to the garden" And here i must refer to the first word in that sentece, Dude.
That place is also my photo studio
And how they look when put in place. Quite the snug fit
And with the outer panel on! (Notice the arm, now without bandages)
Old versus new mobo! Bye Bye blue
A little sleeving (the wire that goes from the aquaero to the onboard usb ports)
"Upskirt" shot.
And in all of her glory
And this is one of my favorite shots so far!
And one showing most of the lower compartment
She is up and running now, and ready to attend s7lan (www.s7lan.dk) where she will hopefully attract some attention
And again, thanks to the sponsors
Until next update, Cya!!!
-p0Pe
is that a 120.9 raddy on your case, or are you just happy to see me?
METO V.1
METO V.2
METO V.3
PC-Beto
Project M8 [WIP]
Dude. You continue to impress. Awesome.
“Do not trust people like me. I will take you to museums, and parks, and monuments, and kiss you in every beautiful place, so that you can never go back to them without tasting me like blood in your mouth. I will destroy you in the most beautiful way possible, and when I leave you will finally understand why storms are named after people.”
Thanks guys
Sooo... What have i been doing? Lots of stuff! A few test at school is over, and i got some more time to work on this, and have some good news for you! I should be able to have this thing done within a week And then i have the time to take her home, into the photo studio and make some glory shots!
Anyway, Uden mad og drikke, dur helten ikke (without food and beverages, the hero dont work)
Oh, and then i used a great deal of time on this, a remote controlled heli
And a close up
And now to the fun stuff! I had to make a new back plate since i lost the old one lol Made some improvements and had some quality time with my dremel!
The result,
A few diskes gone. I am still to cheap to get the quick disconect diskes
Final result before painting^
And now for the fans, i made some stickers to make them look a bit more classy
And insertet into the case, with the cable going into the back wall to the plug.
Now this little hole is the fillport for the hole system! But where does it sit?
Oh yeah, in the top Right above the reservoir. See the aquaero faceplate there? Wonder where this is going...
This^
Ended out like this
And last, but not least, the front panel where the on switch will sit. Need to get this painted!
Tommorow i will have some time to paint and fill down the top, and then there is just some minor stuff left to be done!
And again, thanks to the sponsors
Inside shots in next update Have fun!
is that a 120.9 raddy on your case, or are you just happy to see me?
METO V.1
METO V.2
METO V.3
PC-Beto
Project M8 [WIP]
Charles (CJ) Gantt: Coil Gun // Biohazard // Circuits // 3D Printer // CoD MW2 Case // TBCS 4GHz Club
Sites: The Makers WorkBench // CJ Gantt Photography