Project Mr. Freeze! Pictures! Custom Window Kit! IM ONLY 15!

[Cardan]

ewww get rid of those ide cables. get some round ones or hide the ones you have.

[MrSlacker]

ewww get rid of those ide cables. get some round ones or hide the ones you have.

i think carefully folded flat IDE cables look better then round ones. AMD, fold yours carfully and t will look better.

[AMDSempron]

Thats what I did, I have one ribbon IDE calbe replaced but there is still one more remaning! dang! here are some updated pictures of my baby!

But wait! Im working on a double top exhaust fan mech. to push hot air out of my case! Does this look like a good plan?
http://rc18twebboard.com/topcompplan.JPG
tell me what you think!

Here is some updated pictures! The further down you go, the better the pictures get!

http://rc18twebboard.com/PA050003.JPG
http://rc18twebboard.com/PA050001.JPG
http://rc18twebboard.com/PA050002.JPG
http://rc18twebboard.com/PA050005.JPG
http://rc18twebboard.com/PA050006.JPG
http://rc18twebboard.com/PA050007.JPG
http://rc18twebboard.com/PA050008.JPG
http://rc18twebboard.com/PA050009.JPG
http://rc18twebboard.com/PA050012.JPG
http://rc18twebboard.com/PA050013.JPG
http://rc18twebboard.com/PA050014.JPG
http://rc18twebboard.com/PA050016.JPG
http://rc18twebboard.com/PA050015.JPG
http://rc18twebboard.com/PA050019.JPG
http://rc18twebboard.com/PA050020.JPG
http://rc18twebboard.com/PA050021.JPG
http://rc18twebboard.com/PA050022.JPG
http://rc18twebboard.com/PA050025.JPG
http://rc18twebboard.com/PA050023.JPG

[Cardan]

looking better but you could still try to hide some more of those wires.

[AMDSempron]

i dont know how to hide the rest of the wires, they wont work for me

Can anyone tell me how to take the power wires (the big plug that goes into the motherboard) and make that look out of the way, or make it look part of the theme? any help would be good!

Thanks

[DeathCrush]

just try some cable sleeving. blue or black would look good in your case, maybe even a silver/chrome. http://www.cableorganizer.com/wire-management/

good job so far by the way. nice to see someone else using a Sempron as well
my little Sempron can actually hold up pretty well to my Athlon, although i haven't been able to do any real tests just because it has a slower than heck HDD in it right now

keep modding

[sabrewolf732]

semprons arent very low end, at least the 754's arent. I get 11,300 in sandra at 2.45GHz and I outbench a 3.8 p4 in pretty much everything. A socket a sempron is basically a tbred b

[Xato]

Try and get your cables behind the drive cages...

[Hassle]

Ok, now for the good stuff!
I boght this computer as a barebones! This computer has no special name for it, since it is custom made! But I like to call it the Mr. Freeze 9000!

So Now introducing "Project Mr. Freeze 9000"

Stock Hardware:
83.1 GB Harddrive
556MB DDR Ram (1 Chip)(Using 1 out of 3 Ram Slots available)
AMD Sempron 2300Mhz Processor (Overcloking at 2600Mhz)
GeForce 4 Graphix card
Built in sound card (not sure what type)
DVD/CD-R/CD-RW Combo drive (top)
CD-R/CD-RW Drive (2nd down)
1 3 1/2 inch floppy drive
Huge Power Supply (Not sure what Voltage, but the dude at the comp store said that it could power 4 computers) :-)

UPGRADES
VIA RAID CONTROLER (Have installed but not hooked up to my other hardrives since there is no other harddrives in my beast as of now)
Nexus 3 Channel Fan controller with built in Cathode light converter
2 12' blue cold cathode lights that give it the Mr. Freeze look
Rounded IDE cable runing from board to Both Burners
Gold aluminum duel 4400RPM Harddrive cooler (controled by fan controler)
1 80mm 4 Blue LED Intake fan (3300 RPMS) (Controled by fan controler)
180mm Turbo Exahst fan (4000 RPMS) Controled by fan controler)
I took Some wire that had a mettal tubing look and wraped and ziptied around some of the wires that are more revealing! Again this contributes greatly to the mr freez effect!

Here are some more pictures of my beast!

Fan Controller and Burners
http://rc18twebboard.com/Fancontrolerandcddrives.JPG

Plain Picture of inside
http://rc18twebboard.com/Inside.JPG

Im not sure what these wires are for, but they sit INSIDE the comp, and are connected to a wire that runs from my motherboard to the front audio slots
http://rc18twebboard.com/audiowiresincomp.JPG

Small picture of bottom cathode
http://rc18twebboard.com/bottomcathode.JPG

Side Off Bottom Light on
http://rc18twebboard.com/bottomlitsideoff.JPG

Another picture of the above pose
http://rc18twebboard.com/bottomlitsideoff2.JPG

Cathode on side panel
http://rc18twebboard.com/coldcathodeonwindow.JPG

Computer Side View with lights on
http://rc18twebboard.com/compsideview.JPG

Another picture of the burners and fan controler
http://rc18twebboard.com/fancontrolerandcddrives2.JPG

View of the custom wire job i did for the wires coming off of my hardrive
http://rc18twebboard.com/customharddrivewires.JPG

view of hardrive cooler
http://rc18twebboard.com/harddrivecooler.JPG

where did you buy that bare bones at i used to work for a shop that sold the same stuff you said was in it....

[MisterChief]

Ok, now for the good stuff!
I boght this computer as a barebones! This computer has no special name for it, since it is custom made! But I like to call it the Mr. Freeze 9000!

So Now introducing "Project Mr. Freeze 9000"

Stock Hardware:
83.1 GB Harddrive
556MB DDR Ram (1 Chip)(Using 1 out of 3 Ram Slots available)
AMD Sempron 2300Mhz Processor (Overcloking at 2600Mhz)
GeForce 4 Graphix card
Built in sound card (not sure what type)
DVD/CD-R/CD-RW Combo drive (top)
CD-R/CD-RW Drive (2nd down)
1 3 1/2 inch floppy drive
Huge Power Supply (Not sure what Voltage, but the dude at the comp store said that it could power 4 computers) :-)

Kid, you obviously don't know a whole lot about computers.

Now as for the case mod, I'm liking what I'm seeing so far. You did a really good job on lighting.