This mod just got 1000x better
This mod just got 1000x better
Have you checked out the front page lately?
Projects:
Moe's Tavern | Sponsored by: Mimo Monitors, Crucial, Thermaltake
Book Of Knowledge
The Simpsons rock
just wait dudes you have NO idea of what i have in store for you guys
is that a 120.9 raddy on your case, or are you just happy to see me?
METO V.1
METO V.2
METO V.3
PC-Beto
Project M8 [WIP]
Whats up tbcs! have an update punks! ;P
for helping me out on this project!
And so it began! i started out with about 2.5 square meters of acrylic, and now have little left.
I would like to thank my new sponsors, www.matronics.dk for sending me some AWSOME light for this project! f#ck ccfl´s. get some led strips from there i used them in my privious build, and the one they send me for this one takes the cake! RGB strips with wireless sound controller! Thanks! Tune in soon, and i will update the video with the light effects And thanks to bitspower for helping me out with some goddies that you all know whats gonna be
some of the parts matronic sent!
I also got the parts painted! matte black ftmfw!
i used theese black rivets to rivet it all back together
also got some wire stuff home
now what is all this going to be used for ? :S
THIS!
that ended out like this. See all that wire? Its starting to make sense now huh?
imagine all the little holes where there is wire in, like you see above
that they be sleeved, so that every wire will look like this
Now for the explanation.
The 7 holes that sits in a square in the upper part of the cabletray is getting these inserted into them. You can then swap psu as crazy often as you like, since you dont have wires running in a maze through thousands of holes.
Now for the fun part.
I had to solder the correct cables to each of the 24 pin connector, since they were made with different lengths. Say hello to mister happy solder station!
slowly, but certanly getting all the buggers on, and applying heatshrink on each, so that i wont have any fires in there -.-
fans will have an output port like this:
and the pump will have a slightly different one here:
some of you have seen this pic:
The thing that was in homers background is this:
And it will be mounted like this on the backplate
And how it was put on. I tapped 4 mm holes and used some black dome head 4 mm bolts i have.
The dome head bolts will also be used on the front.
And as you can see, the 24 wires is taking up quite a bit of space in the cable tray:/ dont know if i will be able to fit the 12 wires for the 6 pins, but i have to
The fans also got some love
And the 8 pin got sleeved. This will also be done to the 24 pin, and 6 pins.
The little buggers in front is the clips that i had to use, to get the extender. took some time to get done, but it will be worth it!
i think that was that for this update Next time i will have some more goodies to show you, some of them from my new sponsor, and a little something something that i got made instead of the res i have now
worth the wait? If not, ill update again in a week or so
is that a 120.9 raddy on your case, or are you just happy to see me?
METO V.1
METO V.2
METO V.3
PC-Beto
Project M8 [WIP]
that looks amazing! nice work!
Arctic Cat * Maximum Security * Cribbage Board * Rockin Case * Armor Redux
Tempest SXR * Power House * Red Comet * ICHIWZ * Acrylic Headphone Hook
Continuing sponsorship support from PCBoard.ca
[ORGASM] [/ORGASM]
Amazing mod! where did you find a place with an acyclic bender?
thanks dudes
diluzio91, at a molding factory
is that a 120.9 raddy on your case, or are you just happy to see me?
METO V.1
METO V.2
METO V.3
PC-Beto
Project M8 [WIP]
LMAO, had to google ftmfw hehe, mister happy solder station made me rofl that is an allie I could do with for good solder work.
Had a look at the matronics site to find out more about the rgb strips some good stuff on there and nice sponser to gain , I like what you are doing with the cabe management, nice.
my 1st scratch case made july 2008 (finding my feet)
Air Cube prototype (fin jan 2009) (still finding my feet)
Air Cube v2 now with added cpc stack (fin aug 2010) (getting better)
Project Stealthlow (fin sep 2011) (much improvement)
Lean and Green - modular dual PC scratch build - Paused
Midlag Crisis
Looks great. I really like what you're doing with the cable management, are you just going to have a big box next to the PSU for all the cabling to sit in or something?
TBCS 5TB Club :: coilgun :: bench PSU :: mightyMite :: Zeus :: E15 Magna EVThat we enjoy great advantages from the inventions of others, we should be glad of an opportunity to serve others by any invention of ours, and this we should do freely and generously.
--Benjamin Franklin
Wow, just wow, awesome update, now i am a happy camper